Allen-Bradley 140G-R-TLC63 User manual

Cu/CuAl Terminal lugs for 140G-R
Cu/CuAl Terminali anteriori per cavi
Cu/CuAl Vorderseitige Anschlüsse für Kabel
Cu/CuAl Prises avant pour câbles
Cu/CuAl Terminales frontales para cables
Bul. 140G
DIR 1001137R0001 Version 01
WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
(Follow NFPA70E requirements).
AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
(Seguire i requisiti NFPA70E).
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen
Sie die Anforderungen nach NFPA70E).
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.
Protéger le produit contre les environnements agressifs. (Vous devez respecter la
norme NFPA70E).
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes. (Cumpra as exigências da norma NFPA70E).
Installation - Installazione - Instalación
Instalação - -
140G-R
DIR 1001137R0001 Version 01 - 140G-R-TLC63, 140G-R-TLA63
21
x1
x1
x1
x2
x1
x12
x12
x12
3p
A
B
C
D
E
F
G
H
Ix12
Cu/CuAI (6)x750 MCM
Cu/CuAI (6)x400 mm²
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。（NFPA70Eの要件に従ってください）
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染 。符合NFPA70E要求）物
Lug
Phase
barrier
Carter
Screw
CH 19
M
M 1 2
CH 10
LENGTH M
65 mm (2.56") M 1 2

1
2
FF
GG
II
HH
GG
CC
BB
443 lb-in
(2)
50 Nm
DIR 1001137R0001 Version 01
CH 19
M
M 1 2
CH 10
LENGTH M
65 mm (2.56" ) M 1 2

3
4
Only for upper side
CC
FF
II
HH
GG
AA
BB
(3)
FF
EE
DIR 1001137R0001 Version 01
443 lb-in
50 Nm
CH 19
M
M 1 2
CH 10
LENGTH M
65 mm (2.56" ) M 1 2

5
1"
A
0,05" A0,05" B
1"
B
DIR 1001137R0001 Version 01 (L7263) - B1070
Copyright © 2016 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 140G-IN119B-MU-P - September 2016
Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/
sustainability-ethics/product-environmental-compliance.page
(*) Terminal surfaces must be parallel within 0.05"
min 1.37”/35 mm
min 2.59”/66 mm
505 lb-in
57 Nm
LENGTH M
65 mm (2.56") M 12
6
(*) (*)
Flexible Cable
AWG/kcmil
mm2-
MIN 1/0 AWG 50 -
MAX 750 kcmil 400 -
Stranded Cable