Allen + Roth 1212VA-42-201 User manual

VANITY WITH TOP
ITEM #0731354
MODEL #1212VA-42-201
Serial Number Purchase Date
ATTACH YOUR RECEIPT HERE
Français p. 9
Español p. 17
1
welcoming • sophisticated • inspiring
Questions, problems, missing parts? Before returning to your retailer, call our customer service
department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Friday.
allen + roth®is a registered trademark
of LF, LLC. All Rights Reserved.
BM18041

2
PACKAGE CONTENTS
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install this
product.
WARNING
• Some steps are more easily handled with two adults.
• Assembly and unpacking requires two adults.
CAUTION
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
HARDWARE CONTENTS
Touch-Up Pen
Qty. 1
AA
PART DESCRIPTION QUANTITY
A Vanity 1
B Top (preassembled
to Vanity (A))
1
C Backsplash 1
D Drawer Divider 2
• DO NOT try to pry off top from vanity. Damage to top or vanity may occur.
• Use care when assembling the vanity; take your time and follow the assembly instructions closely.
C
A
B
D
D

3
PREPARATION
Estimated Installation Time: 20-30 minutes (24 hours for silicone caulk to dry).
Helpful Tools (not included): Measuring tape, level
INSTALLATION INSTRUCTIONS
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to
assemble the product.
Tools Required for Installation (not included): Phillips screwdriver, utility knife or scissors, silicone
caulk, power drill with drill bit
1. To remove drawer preassembled in vanity (A),
fully extend drawer. Locate plastic levers on
metal glide tracks at left and right sides of
drawer box and push on plastic levers on both
sides at the same time to disengage drawer
box from the glides. Gently lift the drawer
up to remove it from vanity (A).
1
A

4
INSTALLATION INSTRUCTIONS
WARNING
Vanity (A) MUST be secured to wall.
Note: Clean area where the vanity (A) will be
permanently located prior to beginning installation,
ensuring the vanity (A) will not interfere with any water
supply and drain lines once mounted.
2. With two people, carefully place vanity (A) with
top (B) against the wall in its final location. Find
and mark locations of wall studs behind the
permanent location of vanity (A).
Note: Use preassembled levelers on legs of
vanity (A) to level the item. Twisting the levelers
counterclockwise will increase the height of vanity (A),
twisting them clockwise will decrease it.
3. From inside vanity (A), drill hole through vanity
mounting area and into wall studs. Using
mounting hardware (not included) appropriate
for your installation site, secure vanity (A) to wall
stud. If possible, secure vanity (A) to two wall
studs for increased stability.
2
1
A
B
3
A

5
INSTALLATION INSTRUCTIONS
4
A
1
3
2
CAUTION
4. To reinstall drawer into vanity (A), fully extend
metal glide tracks. Gently lower and slide
drawer box into rear glide catch. Next, lower
drawer box down to completely rest on
extended glides. Then, push plastic levers to
lock the drawer box in place.
Note: To adjust the drawer box height, spin
the adjustment wheel to the left to raise the
drawer box or spin the adjustment wheel to
the right to lower the drawer box. You can
adjust the left and right side glide heights
independently in order to find the drawers best
alignment position.
• DO NOT force drawer or damage to glide
may occur. If drawer does not slide in with
ease, remove and try again from the start.
5
DE
5. Insert two drawer dividers (D) into the notch of
drawer inside.

6. Apply silicone caulk (not included) to unpolished
side and bottom of backsplash (C). Position
backsplash (C) on top (B) and against wall.
Clean any excess caulk before allowing
to dry.
Assembly is now complete. Install desired faucet
and drain assemblies (neither included) per the
manufacturers' instructions to complete
the installation.
6
INSTALLATION INSTRUCTIONS
6
22
CB
1

7
WARRANTY
CARE AND MAINTENANCE
IMPORTANT
• Dust the vanity regularly with a soft, non-lint producing cloth or household dusting product.
• You can clean the vanity with a gentle, non-abrasive household cleaner.
• Make sure to dry the wood immediately with a soft cloth or towel.
• The stone top can be cleaned using standard marble cleaning agents available at your local
supplier.
• Tips for using touch-up pen (AA): For scratches, stroke in direction of scratch. Rub off excess
colorant promptly with a soft cloth.
• Shade variations and patterns are an inherent characteristic of stone (e.g. granite, marble,
engineered stone). Stone tops will vary from product to product. Use caution placing items such as
soap or any fragranced material on the stone surface. Use a soap dish, coaster or similar item to
protect the surface if placing any soap or fragranced products on the stone.
• If soap or fragranced products come in contact with the stone top, rinse the surface with water and
dry using a soft non-abrasive cloth.
• Stone care products are available at your local home center store. Follow the manufacturer's
directions on how to use.
• DO NOT use products to clean the stone top that contain acetone, lemon, vinegar or other acids as
these may cause damage to the stone surface.
• Periodically reseal the stone top using an appropriate stone sealer available from your local home
store. Follow the manufacturer's directions on how to apply.
The manufacturer warrants this item against defects in materials and workmanship for a period of one
(1) year from the date of original retail purchase. This warranty applies only to the original purchaser.
This warranty does not apply to any damage on the product by accident, misuse, or modified,
improper installation or by affixing accessories not produced by the manufacturer. The manufacturer
is not accountable whatsoever for product installation during the warranty period. There is no further
expressed warranty. The manufacturer shall not be legally responsible for incidental, consequential
or special damages arising at or in connection with product use or performance except as may
otherwise be accorded by law. The manufacturer disclaims any and all implied warranties.

REPLACEMENT PARTS LIST
Printed in Vietnam
8
For replacement parts, call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST,
Monday - Friday.
allen + roth®is a registered trademark of
LF, LLC. All Rights Reserved.
PART DESCRIPTION PART #
CBacksplash PF-1012VA-42-201-001
BTop PF-1012VA-42-CAR-TOP
DDrawer Divider PF-1012VA-42-201-002
ETop Divided Drawer PF-1012VA-42-201-003
FBottom Drawer PF-1012VA-42-201-004
GSink PU17-18x14-SQUARE
AA Touch-Up Pen OF-0010 (W2108)
BB Glide Track Set PUDTC-12x3-HANDLE
CC Drawer Pull CF-001-BN
DD Leveler T-1007
AA CCBB DD
C
G
B
D
E
F

ARTICLE # 0731354
MODÈLE # 1212VA-42-201
JOIGNEZ VOTRE REÇU ICI
9
Numéro de série Date d’achat
welcoming • sophisticated • inspiring
allen + roth®est une marque de commerce
déposée de LF, LLC. Tous droits réservés.
MEUBLE-LAVABO AVEC COMPTOIR
Des questions, des problèmes, des pièces manquantes? Avant de retourner l’article au détaillant, ap-
pelez notre service àla clientèle au 1 866 439-9800, entre 8 h et 20 h (HNE), du lundi au vendredi.

CONTENU DE L’EMBALLAGE
CONSIGNES DE SÉCURITÉ
Assurez-vous de lire et de comprendre l’intégralité de ce manuel avant de tenter d’assembler, d’installer
ou d’utiliser le produit.
AVERTISSEMENT
• Certaines étapes sont plus faciles à effectuer avec l’aide d’un deuxième adulte.
• L’assemblage et le déballage nécessitent deux adultes.
ATTENTION
VEUILLEZ CONSERVER CES INSTRUCTIONS POUR VOUS Y RÉFÉRER ULTÉRIEUREMENT.
QUINCAILLERIE INCLUSE
Crayon à retouche
Qté : 1
AA
10
PIÈCE DESCRIPTION QUANTITÉ
A Meuble-lavabo 1
B Comptoir (préassemblé
au meuble-lavabo [A])
1
C Dosseret 1
D Séparateur de tiroir 2
• Ne tentez pas de retirer le comptoir du meuble-lavabo; vous risqueriez d’endommager le comptoir
ou le meuble-lavabo.
• Soyez prudent lors de l’assemblage du meuble-lavabo; prenez votre temps et suivez minutieuse-
ment les instructions pour l’assemblage.
C
A
B
D
D