Allen + Roth PERGOLA A106000902 User manual

ITEM #0878763/38115235
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our
customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.
RR20299
ATTACH YOUR RECEIPT HERE
1
Français p. 919
PERGOLA
MODEL # A106000902
ALLEN + ROTH and logo design are
trademarks or registered trademarks of LF,
LLC. All rights reserved.
ALLEN + ROTH et le logo sont des marques de
commerce ou des marques de commerce
déposées de LF, LLC. Tous droits réservés.

2
PACKAGE CONTENTS
O1
F1
B
B
I
H
K
K
P
Q
N
C
C
L4
L3
M1 A4
A3
A3
A4
O2
G3
G2
E1
D2
D3

3
PACKAGE CONTENTS
A3
A4
B
C
Post A
Post B
Arc Beam
Beam
Top Beam A
Top Beam B
PART DESCRIPTIONQUANTITY
2
4
2
4
7
7
2
4
4
2
4
4
8
4
2
2
Connector
Arc Connector
K
L3
L4
M1
Support Bar A
Support Bar B
Rail Tube Connector
Fabric Tube A
Fabric Tube B
Rail Tube
4
2
4
O1
P
Q
Ferrule A
Base Cover
Base
1
NCanopy
Post Decoration
Beam Decoration
D2
D3
E1
F1
G3
I
G2
H
2
O2 Ferrule B

4
HARDWARE CONTENTS (not shown to size)
M6 x 20 mm Short Bolt M6 Flat Washer
Qty. 40 + 2 spare Qty. 136 + 10 spare
AA BB
M6 x 60 mm Middle Bolt
GG
HH
Qty. 16 + 2 spare
Qty. 2
M6 Wrench
ZZ
M6 x 15 mm Bolt
Qty. 18 + 2 spare
Φ8 x 180 mm Stake
Qty. 8
M6 x 70 mm Long Bolt
Qty. 22 + 2 spare
EE FF JJ
M6 Spring Washer
Qty. 84 + 8 spare
LL
Qty. 48 + 2 spare
M6 Nut

SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble or
install the product.
• Keep all children and pets away from assembly area. Children and pets should
be supervised while pergola is being assembled.
• This pergola is for domestic outdoor use.
• Install the pergola on level ground. Stakes are provided to secure the pergola to
the ground. Do not assemble the pergola on sandy, muddy or loose soil, as
stakes do not have enough holding strength in these types of soil. If you wish to
secure the pergola to a wood deck or concrete surface, use anchors suited to
these surfaces (anchors not included).
• Some parts may contain sharp edges. Wear protective gloves if necessary
during assembly.
• This unit is heavy. DO NOT assemble this item alone. Make sure there is
sufficient manpower for safe assembling or moving of the pergola.
• Check all nuts and bolts periodically for tightness and when required, tighten
them again.
• ALWAYS REMOVE the tent before experiencing heavy wind conditions, as
it is a semi-permanent construction and not designed to withstand harsh
weather, including high wind or heavy rain and snow.
• Keep all flame and heat sources away from the tent fabric. This tent is made
with fabric that meets CPAI-84 specifications for flame resistance. It is not
fire proof. The fabric will burn if left in continuous contact with any flame
source. The application of any foreign substance to the tent fabric may render
the flame-resistant properties ineffective.
WARNING
• DO NOT use or enter the pergola during harsh weather (e.g. thunderstorms,
high winds, hail, heavy snow, etc). In these conditions, it might tip over and
could cause serious injury to bystanders. Any damage or injury caused by
these conditions is not covered by the warranty.
• DO NOT install the pergola adjacent to trees a sloped roof. Snow and ice
may slide onto the pergola and cause it to collapse.
• DO NOT hang any weights on the roof frame.
• DO NOT use a ladder leaning against the pergola for climbing onto the roof.
• Keep away from heat or flame sources.
• If the pergola will not be used for a long period of time (e.g. during winter
time), disassemble and store it in a clean, dry environment.
CAUTION
5

PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list and hardware contents list. If any part is missing
or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 60 minutes
Tools Required for Assembly (included): Wrench.
Tools Required for Assembly (not included): Phillips screwdriver, hammer, and
ladders (no less than 8.2-feet tall).
4 people are needed for assembly. A safety helmet should be worn during
assembly.
6

7
ASSEMBLY INSTRUCTIONS
1. Insert the posts (A3/A4) into the base
covers (P), then attach the bases (Q) to the
posts (A3/A4) using bolts (AA) and washers
(BB). Tighten with wrench (ZZ).
Hardware Used
x 8
x 8
AA M6 x 20 mm Short Bolt
BB M6 Washer
ZZ M6 Wrench x 1
1
AA BB
A3 A4
P
Q
ZZ
P
A4
A3
I
C
G2
H
B
G2
O2
2. Place the post decoration (G3) onto the top
of the posts (A3/A4). 2
2
G3
O1
G3
A3 A4

8
ASSEMBLY INSTRUCTIONS
•
3-3. Attach the other beams (C） to the
beam assemblies (C/E1/O2) and
secure with bolts (AA) and
washers (BB/LL) , tighten with
wrench (ZZ).
Insert the connectors (E1) to the
beams(C), secure with bolts (AA) and
washers (BB/LL), tighten with wrench
(ZZ) .
3-1
Hardware Used
AA M6 x 20 mm Short Bolt
BB M6 Washer
x 4
x 4
x 4
M6 Wrench
ZZ x 1
Hardware Used
3-1
3-3
LL M6 Washer
AA
LL
BB
AA M6 x 20 mm Short Bolt
BB M6 Washer
x 4
x 4
x 4
x 1
LL M6 Washer
ZZ M6 Wrench
AA
LL
BB
3-1.
Attach the Ferrule B (O2) to beam
assemblies (C/E1).
3-2
3-2.
C
O2
C O2
E1
C E1
C

9
4. Attach the assembled beams (C) to the
posts (A3/A4) through the post decoration
(G3), secure with bolts (AA) and
washers (BB/LL), tighten with wrench (ZZ).
Insert the arc connectors (F1) to the arc
beams(B), secure with bolts (AA) and
washers (BB/LL), tighten with wrench (ZZ).
5-2. 11
5-2
11
5
11
4
11
6
11
5-1
Hardware Used
Hardware Used
11
5
11
4
11
6
11
5-1
11
5-2
O1
AA M6 x 20 mm Short Bolt x 16
x 16
x 16
x 1
BB M6 Washer
LL M6 Washer
ZZ M6 Wrench
AA
LL
BB
AA M6 x 20 mm Short Bolt x 4
x 4
x 4
x 1
BB M6 Washer
LL M6 Washer
ZZ M6 Wrench
B
AA
LL
BB
B
C
5-1.
Attach the Ferrule (O1) to the assembled
arc beams (B) and arc connector (F1).
G3
A3 A4
F1
F1
ASSEMBLY INSTRUCTIONS

10
ASSEMBLY INSTRUCTIONS
5-3. Attach the other arc beams (B）to the
arc beam assemblies (B/F1/O1) and
secure with bolts (AA) and washers
(BB/LL) , tighten with wrench (ZZ).
7-25-3
6.
Hardware Used
Hardware Used
GG M6 Nut
BB M6 Washer
M6 Wrench
ZZ
x 16
x 16
x 2
7-25-3
B B
O1
AA
LL
BB
AA M6 x 20 mm Short Bolt x 4
x 4
x 4
x 1
BB M6 Washer
LL M6 Washer
ZZ M6 Wrench
x 32
HH M6 x 60 mm
Middle Bolt
x 16
LL M6 Washer
Connect the assembled arc beams (B)
with the beam decorations (G2) through
the holes of assembled beams (C) using
bolts (HH), washers (BB/LL) and nuts
(GG), tighten with wrench (ZZ) .
6
G2 HH
BB
GG
LL
BB C
B