Allen + Roth L-GZ401PCO-D User manual

HARDTOP GAZEBO
ITEM #0732510
MODEL #
L-GZ401PCO-D
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Friday.
AB 17836
ATTACH YOUR RECEIPT HERE
26
1
TM
Français p. 26

2
PACKAGE CONTENTS
H5
J1
E5 C5
C4
K5
H4
N1
N2M2
K3 O3 J3
I1
Q2
F1
B4
F4
G4 Y2
I5
A4
G5
L4 D3 I3 M3 L3 N3
D5 F5
P2

3
PACKAGE CONTENTS
PART
Y2
F1
N1
I1
J1
Decorative Gutter
Decorative Gutter Connector
Corner Connector
Mosquito Netting Tube
Corner Decorative Gutter
Top Slanting Bar
Middle Beam
DESCRIPTIONQUANTITY
M2
Q2
4
8
4
8
4
4
4
8
8
1
4
1
1
4
4
1
1
4
4
4
1
4
Long Support Beam
N2
Short Support Beam
Big Top Frame
Small Top Roof Cover 1
Top Decor
Chandelier Hook
Small Top Bottom Beam
Small Top Sheeting
Small Top Roof Cover 2
Small Top Bottom Connecting Frame
Small Top Connector
Post Base
Base Cover
Post
Top Block
D3
I3
J3
K3
L3
M3
N3
K5
O3
4
4Right Arc Support
Left Arc Support
4
4
4
4
4
4
16
1
Left Middle Big Top Cover
Right Middle Big Top Cover
Left Small Big Top Cover
Right Small Big Top Cover
Middle Big Top Cover
Top Cover
Roof Press Sheet
Mosquito Netting
A4
B4
C4
H4
G4
F4
C5
D5
E5
F5
G5
H5
I5
P2
L4

4
HARDWARE CONTENTS (not shown to size)
M6
Flat Washer
Qty.284 +15 spare
CC
MM NN
BB
M6 x 15 mm
Bolt
Plastic Cap
M6
Wrench
M6 X 80 mm Anchor
II LL
HH
M6
Hooded Nut
Qty. 4 + 1 spare
Qty. 2
KK
JJ
AA
OO
￠8 X 180 mm
M6 x 20 mm
Bolt M6 Spring Washer
Qty. 48 + 3 spare
M6 x 40 mm
Bolt
Qty. 8 + 1 spare
Hook
Qty. 48 + 3 spare
Qty. 16 spare
Stake
Qty. 8
Qty. 8
Qty.208 + 11 spare
Qty. 68 + 4spare

• Check all nuts and bolts periodically for tightness and when required, tighten them
again.
• While this gazebo is manufactured to withstand winds through only the supplied
ground stakes, in areas subject to frequent severe weather, securing the gazebo
to a deck, concrete patio or footings should be considered.
• Do not use a ladder leaning against the gazebo or climb onto the roof.
• Do not use or enter the gazebo if there exists any of the following or of similar
conditions:
1. Visible movement of support members, roofing panels or sagging roofline.
2. Creaks or audible noise from the gazebo.
3. Cracks, fractures or malformation of support members or roof panels.
4. Damaged or missing fasteners.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble or
install the product.
• Keep all children and pets away from assembly area. Children and pets should
be supervised while gazebo is being assembled.
• The assembled gazebo should be located at least 6 feet from any obstruction
such as fence, garage, house, overhanging branches, laundry lines or electrical
wires.
• Some parts may contain sharp edges. Wear protective gloves if necessary during
assembly.
• This unit is heavy. For safety, do not assemble this item alone. Six to eight people
are recommended for safe assembly.
WARNING
• Install the gazebo on level ground. Stakes are provided to secure the gazebo to
the ground. Do not assemble the gazebo on sandy, muddy or loose soil, as stakes
do not have enough anchorage in these types of soil. If you wish to secure the
gazebo to a wood deck or concrete surface, use anchors suited to these surfaces.
• Snow must be cleared off regularly during snowy day. Remove the snow at the top
when it is thicker than 4 inches. In order to avoid damages, use a plastic snow
rake to remove excessive snow and ice buildup from roof and keep away from
falling debris.
CAUTION
5
•Keep all flame and heat sources away from the tent fabric. This tent is made with
fabric that meets CPAI-84 specifications for flame resistance. It is not fire proof.
The fabric will burn if left in continuous contact with any flame source. The
application of any foreign substance to the tent fabric may render the flame-
resistant properties ineffective.

PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list and hardware contents list. If any part is missing
or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 150 minutes
Tools Required for Assembly (included): Wrench.
Tools Required for Assembly (not included): Phillips screwdriver, hammer, and 2
ladders (no less than 8.2-feet tall).
6
• For outdoor use only.
• Chandelier hook maximum weight: 33 lbs.
• Any assembly or maintenance of the product must be carried out by adults only.
• Please check your state and local regulations prior to purchasing. Some jurisdictions
may require permits for installation and use. Some special procedures may be
valid in your area.

7
ASSEMBLY INSTRUCTIONS
1. Connect decorative gutter connectors (F1)
and corner decorative gutters (J1) using
bolts (CC) and flat washers (BB). Tighten
with wrench (LL)
2. Attach decorative gutters (Y2) to decorative
gutter connectors (F1) using bolts (CC) and
flat washers (BB). Tighten with wrench (LL).
Hardware Used
x 16
x 16
x 1
Hardware Used
x 16
x 16
x 1
1
2
I1
N1
I1
I1
I1
Y2
J1
J1
J1
J1
Y2
Y2
N1
Y2
Fig.2
Fig.1
Fig.3
Fig.4
Fig.5
1
CC
BB
J1
F1
CC
2
BB
J1
Y2
F1
BB M6 Flat Washer
CC M6 x 15 mm Bolt
BB M6 Flat Washer CA
CC
LL M6 Wrench
LL M6 Wrench
6 x 15 mm Bolt

8
ASSEMBLY INSTRUCTIONS
•
3. Attach corner connectors (N1) to corner
decorative gutters (J1) using bolts (CC)
and flat washers (BB). Tighten with
wrench (LL).
Hardware Used
x 8
x 8
x 1
3
BB
J1
Plastic Cap
Hardware Used
Hook
AA
x 48
x 16
4. Attach plastic caps (AA) to one end of
each mosquito netting tube (I1), then insert
6 hooks (JJ) into the inside rail of tube as
shown.
Then, attach plastic caps (AA) to the other
ends of each mosquito netting tube (I1).
4
I1
AA
JJ
HH
I1
JJ
x 16
Hardware Used
x 1
x 16
5. Attach mosquito netting tubes (I1) to the
inside of the decorative gutters (Y2) and
corner decorative gutters (J1) using bolts
(CC) and flat washers (BB). Tighten with
wrench (LL).
5
CC
CC
BB
BB
Y2
J1
I1
I1
BB M6 Flat Washer
CC M6 x 15 mm Bolt
BB M6 Flat Washer
CC M6 x 15 mm Bolt
LL M6 Wrench
LL M6 Wrench
CC
N1

9
ASSEMBLY INSTRUCTIONS
6. Attach the lower ends of top slanting bars
(M2) to the corner connectors (N1) using
bolts (CC), flat washers (BB) and nuts
(OO). Tighten with screwdriver (not
included).
Hardware Used
BB M6 Flat Washer x 16
x16
x 1
Fig.11
Fig.12
Fig.10
Fig.7
Fig.9
Fig.8
M2
L4
P2
N1
N1P2
N2
N2
Y2
J1
J1
J1
Y2
Q2
Q2
K2
M2
M2
M2
N1
BB
CC
CC
7. Attach the top ends of top slanting bars
(M2) to the big top frame (L4) using bolts
(CC) and flat washers (BB). Tighten with
wrench (LL).
Hardware Used
x 8
x 8
x 1
12-112-112-1
7
L4
M2
BB
CC
CC
BB
BB M6 Flat Washer
CC M6 x 15 mm Bolt
LL M6 Wrench
6
OO
AA
M6 x 15 mm Bolt
LL M6 Wrench

10
ASSEMBLY INSTRUCTIONS
Hardware Used
x 8
x 8
x 1
8. Attach the top ends of middle beams (Q2)
to the big top frame (L4) using bolts (CC)
and flat washers (BB). Tighten with
wrench (LL).
BB
CC
CC
BB
8
Q2
9. Attach middle beam (Q2) to decorative
gutter (Y2) using bolts (CC) and flat
washers (BB). Tighten with wrench (LL)
Hardware Used
x 8
x 8
10. Attach one end of left long support
beams (N2) to middle beams (Q2) using
bolts (CC) and flat washers (BB). Tighten
with screwdriver.
10
Hardware Used
x 16
x 16
Q2
N2
BB
CC
BB M6 Flat Washer
CC M6 x 15 mm Bolt
LL M6 Wrench
9
BB M6 Flat Washer
CC M6 x 15 mm Bolt
Q2
Y2
CC
BB
BB M6 Flat Washer
CC M6 x 15 mm Bolt
x 1
LL M6 Wrench
L4