Alliance Laundry Systems IGHP190E Owner's manual

Programming
Tumble-Dryers
Flex Control
Refer to Page 7 for Model Identification
Original Instructions
Keep These Instructions for Future Reference.
CAUTION: Read the instructions before using the machine.
(If this machine changes ownership, this manual must accompany machine.)
www.alliancelaundry.com Part No. D1621ENR3
October 2017

Table of Contents
Machine Type Selection:......................................................................... 6
Model Identification .............................................................................. 7
Warnings and Symbols........................................................................... 8
Warnings........................................................................................................8
Symbols Used ............................................................................................... 9
Programming and Emergency Stop Switch.................................................. 10
Main Menu...................................................................................................11
Basic Description of Controls................................................................ 12
General ....................................................................................................... 12
Specific Information .....................................................................................12
20 Dryer Programs - 5 Steps.......................................................................... 13
The Creation of a Dryer Program ...................................................................13
Programming the Functions .......................................................................... 14
Initializing the Machine........................................................................ 15
Initializing Steps...........................................................................................15
Initialization Menu .......................................................................................15
Configuration Menu......................................................................................17
How to Create and Adjust a Dryer Program.....................................................22
Programming........................................................................................23
General ....................................................................................................... 23
Step 1: Program Menu ..................................................................................23
Step 2: Program Functions............................................................................. 23
Step 3: Program Step Functions .....................................................................24
Step 4: Programming the Drying Part .............................................................25
Operation menu....................................................................................28
Start Up ...................................................................................................... 28
Switch On the Power.....................................................................................28
Load the Dryer............................................................................................. 28
Start a Dryer Program....................................................................................28
The Active Program ..................................................................................... 28
Advancing a Dryer Program...........................................................................28
Drying Time.................................................................................................28
Program End................................................................................................ 28
© Copyright 2017, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed
written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
3 Part No. D1621ENR3

Cool-Down Function ....................................................................................29
Stop ............................................................................................................29
Wait State.....................................................................................................29
How to Handle Failure Messages................................................................... 29
How to Handle Power Interruptions................................................................29
Service-State Button .....................................................................................29
Humidity Control..........................................................................................30
Pre-programmed programs...................................................................32
General ....................................................................................................... 32
Drying Programs ..........................................................................................32
Troubleshooting.................................................................................... 36
Display Messages ........................................................................................ 36
Fault Messages ............................................................................................ 36
How to Handle Fault Messages ..................................................................... 36
Clean Filter ................................................................................................. 37
Overview..................................................................................................... 37
Service Menu .............................................................................................. 39
Diagnostic Program ......................................................................................41
Problem Check List.......................................................................................42
Explanation of Error Messages.......................................................................43
Failure 1: Heating Safety 1.........................................................................43
Failure 2: Heating Safety 2.........................................................................43
Failure 3: Pressure Sensor Low ..................................................................43
Failure 4: Pressure Sensor High ................................................................. 44
Failure 5: Motor Thermic........................................................................... 44
Failure 6: Fan Motor Thermic.....................................................................44
Failure 7: Drum Motor Thermic..................................................................45
Failure 8: Airflow Switch Open at Start-up.................................................. 45
Failure 9: Airflow Switch Open After Start-up............................................. 45
Failure 10: Airflow Switch Closed.............................................................. 46
Failure 11: Fault Cool down....................................................................... 46
Failure 12: No Reheating........................................................................... 46
Failure 13: No Heating...............................................................................47
Failure 14: Heat time ................................................................................ 47
Failure 15: Too Hot................................................................................... 47
Failure 18: Too Hot Safety......................................................................... 48
Failure 19: Defective Temperature Sensor 1.................................................48
Failure 20: Defective Temperature Sensor 2.................................................48
Failure 25: No Humidity Sensor (HUMIDITY CONTROL ONLY)................49
Failure 26: No Humidity Sensor Cap (HUMIDITY CONTROL ONLY)......... 49
Failure 27: No Humidity Reduction.............................................................49
Failure 28: Lint Filter.................................................................................50
Failure 29: Timeout Cooldown .................................................................. 50
Failure 35: Wrong Software Version............................................................50
Failure 37: Too Hot Safety......................................................................... 50
Failure 39: Error Fan .................................................................................51
Failure 40: Phase Error ..............................................................................51
Failure 41: Service Due .............................................................................52
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
4 Part No. D1621ENR3

Failure 95: Watch Dog............................................................................... 52
Failure 150-165: Memory Errors.................................................................52
Failure 170-199: Sofware Errors................................................................. 52
Humidity Control - Troubleshooting............................................................... 52
Service information...............................................................................54
General........................................................................................................ 54
Maintenance ................................................................................................54
Information for Service .................................................................................54
Programmer Circuit Board ............................................................................ 54
Instructions for Replacing the Electronic Board and Keypad ............................ 54
Instructions for Installing New Software ........................................................ 55
Specification of Your Machine...............................................................56
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
5 Part No. D1621ENR3

Machine Type Selection:
Dry load ca-
pacity
“Machine
type” selec-
tion
Tumble Dryer 190 Liters
(9Kg)
» T9
250 Liters
(11Kg)
» T11
285 Liters
(13Kg)
» T13
345 Liters
(16Kg)
» T16
Machine Type Selection:
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
6 Part No. D1621ENR3

Model Identification
Information in this manual is applicable to these models:
190 Liters (9 Kg) IGHP190E SGHP190E UGHP190E
IGHP190F SGHP190F UGHP190F
IQHP190E SQHP190E UQHP190E
IQHP190F SQHP190F UQHP190F
IUHP190E SUHP190E UUHP190E
IUHP190F SUHP190F UUHP190F
IWHP190E SWHP190E UWHP190E
IWHP190F SWHP190F UWHP190F
250 Liters (11 Kg) IGHP250E SGHP250E UGHP250E
IGHP250F SGHP250F UGHP250F
IQHP250E SQHP250E UQHP250E
IQHP250F SQHP250F UQHP250F
IUHP250E SUHP250E UUHP250E
IUHP250F SUHP250F UUHP250F
IWHP250E SWHP250E UWHP250E
IWHP250F SWHP250F UWHP250F
285 Liters (13 Kg) IGHP285E SGHP285E UGHP285E
IGHP285F SGHP285F UGHP285F
IQHP285E SQHP285E UQHP285E
IQHP285F SQHP285F UQHP285F
IUHP285E SUHP285E UUHP285E
IUHP285F SUHP285F UUHP285F
IWHP285E SWHP285E UWHP285E
IWHP285F SWHP285F UWHP285F
345 Liters (16 Kg) IGHP345E SGHP345E UGHP345E
IGHP345F SGHP345F UGHP345F
IQHP345E SQHP345E UQHP345E
IQHP345F SQHP345F UQHP345F
IUHP345E SUHP345E UUHP345E
IUHP345F SUHP345F UUHP345F
IWHP345E SWHP345E UWHP345E
IWHP345F SWHP345F UWHP345F
Model Identification
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
7 Part No. D1621ENR3

Warnings and Symbols
Warnings
WARNING
Before operating a machine controlled by an elec-
tronic programmer, read this manual. Incorrect use
can result in serious injuries or damage to the ma-
chine controls. Ignoring instructions can cause an
incorrect machine function, which may result in inju-
ries or machine and/or linen damages.
C001
• This English version is the original version of this manual.
Without this version, the instructions are incomplete. Before
installation, operating and maintenance of the machine, read
complete instructions thoroughly. Refer to the Installation/
Operation/Maintenance manual for further important instruc-
tions, as well. Follow these and keep the manuals accessible
for later use.
• A machine must be installed by following the Installation/
Operation/Maintenance manual. Before the first machine
start, it must be initialized and tested by a qualified techni-
cian.
• The electric service line must not be affected by other electri-
cal loading. A nominal voltage, if loaded or not must work in
the range ±10% with a maximum permanent frequency devia-
tion of 1% or a short-time one at 2% of a given frequency.
NOTE: Connecting or starting the machine at an in-
correct voltage can damage the programmer.
• The machine must not be exposed to high humidity or ex-
treme high and low temperatures.
• Do not tamper with the controls.
INSTRUCTIONS IN THIS MANUAL DO NOT COVER
ALL DANGEROUS SITUATIONS. IT IS UP TO THE USER
TO HANDLE THE MACHINE CAREFULLY.
• The manufacturer has the right to change specifications in this
manual without prior notice. All the stated information is only
for informative purpose and must be considered as general. It
is not possible to present all the specific data of the device.
NOTE:
Every circuit board has a serial number and the code of
the board (Refer to Figure 1).
On the EPROM memory chip on the circuit board is a
label specifying the software number and version
and/or the date of the software. (Refer to Figure 1).
These data, as well as the model and serial number of
the machine, must be mentioned in all correspondence
or inquiries addressed to the distributor or manufactur-
er.
NOTE:
The FLEX CONTROL computer uses "machine type"
codes to select the different programmable machine
versions.
The model number on the machine doesn’t indicate the
"machine type" but must be linked with the description
of the "machine type" letters.
• Tx : Single Dryer
• Tx, x : Double Dryer
Warnings and Symbols
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
8 Part No. D1621ENR3

Symbols Used
BUTTONS
Figure 1 U models
BUTTONS
Figure 2 I models, S models
START
- Starting up a program
- Continue an interrupted program
- Advancing the program step by step
REVERSE
- Switch On/Off Reverse function
STOP
- Interrupting a program
- Finishing a program
SERVICE
- shows the states and the total number of cycles of the machine
CFD1307R_SVG
CONFIRM THE SELECTION
DRYING TIME
- Setting for drying time
Table 1 continues...
Warnings and Symbols
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
9 Part No. D1621ENR3

CFD1309R_SVG
or ARROW UP
- Increasing a value
- Selecting the next element of an item list
PROGRAM SELECTION
- Selecting a program number
CFD1310R_SVG
or ARROW DOWN
- Decreasing a value
- Selecting the previous element of an item list
DRYING TEMPERATURE
- Setting for temperature
or ARROW LEFT
- Selecting the previous menu item
COOLDOWN TIME
- Setting for cool down time
or ARROW RIGHT
- Selecting the next menu item
MOISTURE LEVEL
- Setting for residual moisture level
Table 1
Programming and Emergency Stop Switch
PROGRAMMING SWITCH
Programming switch is located inside the machine behind the
control panel.
To access the programming switch:
• Machines 190 Liters (9 kg) – remove top cover.
• Machines 250, 285, 345 Liters (11-13-16kg) - the control pan-
el must be unlocked
1. Programming switch
Figure 3
Run Mode: This is the Normal Dryer operation.
Program Mode: Only for changing the Dryer programs and ma-
chine settings.
Warnings and Symbols
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
10 Part No. D1621ENR3

EMERGENCY STOP SWITCH
The emergency stop switch is only available on non-coin dryers.
Main Menu
Warnings and Symbols
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
11 Part No. D1621ENR3

Basic Description of Controls
General
THE CONTROL OFFERS :
• 20 programmable programs (including 9 pre-programmed
ones) kept in memory
• Each Program can be build in 5 steps
• Setting the machine options and configuration
• Multiple languages can be selected (one at a time)
IN OPERATION THE FOLLOWING DATA IS DISPLAYED :
• The selected program
• The active step
• The remaining program time
• The sequence function
• Indication of wait
• The temperature can be viewed
• Diagnostic messages
THE OPERATION MENU :
• A program can be manually Shortened, Extended, Stopped.
• Service information
• Special function buttons to create simple dryer program
THE HARDWARE AND SOFTWARE OF THE FLEX CON-
TROL DRYER COMPUTER
• Easy operation by a comprehensive keypad
• The hardware contains 1 electronic board
• The FLEX CONTROL board with Alphanumerical LCD dis-
play
• The dryer control software is implemented in a Flash Memory
that can be easily replaced
• The Dryer Programs are kept in EEPROM memory ( non-vol-
atile memory)
Specific Information
The PROGRAM Menu is designated for :
• The creation and implementation of a new dryer program step
by step.
• Editing a dryer program step by step.
• Adding, inserting and deleting steps in the dryer program.
• Copying a dryer program.
• Inspecting the dryer program by the view function.
The CONFIGURATION Menu is designated for :
• The selection of the machine type.
• Loading the default factory settings for the CONFIGURA-
TION and INITIALIZATION menu.
• Erasing all the programmed dryer programs (reset Dryer pro-
gram EEPROM memory).
• Loading the standard dryer programs.
• The selection if the temperature must be displayed in degrees
Celsius or degrees Fahrenheit.
• The selection of the Brightness of the display.
The INITIALIZATION Menu is designated for :
• The selection of the displayed Language.
• Programming the Service due value.
• The selection of the Buzzer time interval.
• The selection of the Advance function.
• Programming the Default Motor On and Off times for revers-
ing motor action.
The SERVICE Menu is designated for :
• The inspection of the error messages log register and the list
with statistics.
• The inspection of the functionality of the electric input sig-
nals.
• Resetting the cycle counter.
The DIAGNOSTIC Menu is designated for starting up a diagnos-
tic program.
Basic Description of Controls
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
12 Part No. D1621ENR3

20 Dryer Programs - 5 Steps
The Creation of a Dryer Program
• A Dryer Program is built up step by step.
Basic Description of Controls
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
13 Part No. D1621ENR3

• Each step always consists of a Dry sequence and a Cooldown
sequence.
• You will notice that each step has default settings. This fea-
ture is very helpful as most of the newly created programs
will not require changes to be made to the suggested values.
Programming the Dryer sequence :
• First set the target temperature.
• Then set the Dry time or Humidity (only applies to machines
fitted with a humidity sensor).
Programming the Cooldown sequence :
• After programming the Dry sequence, next program the Cool-
down sequence.
• Set the parameter to stop the Cooldown sequence : Time or
Temperature
• As you will notice it’s also possible to skip a sequence be-
tween two other sequences by programming a time value =
0. )
The Anti-Wrinkle sequence :
• To avoid Wrinkling, its recommended that the linen is re-
versed each 2 to 10 minutes once the drying cycle has finish-
ed and the machine is not unloaded. A beep signal warns the
operator that the cycle has been finished.
WARNING
A MORE DETAILED EXPLANATION FOR THE SPE-
CIFIC SEQUENCES CAN BE FOUND IN CHAPTER
PROGRAMMING.
C105
The Final Cooldown sequence :
• To avoid that the linen stays in the dryer with a too high tem-
perature, for safety purposes, a Final Cooldown sequence is
added at the end of the program.
• The Final Cooldown sequence takes 3 minutes if the tempera-
ture is above 50 °C, then the program is finished.
•The Final Cooldown sequence cannot be changed.
Programming the Functions
Limits:
• To ensure the correct functionality of the dryer you have to
program values within certain limits.
• If you program a value that falls below the minimal or above
the maximal programmable limit then the new value will not
be accepted and the previous value stays valid.
Programming the Dry Temperature
• Limits:
• Dry Temperature : 1 - 70 °C
Programming the Dry Time
• Limits:
• Dry Time : 0 – 120 Minutes
Programming the Cooldown Time
• Limits:
• Cooldown Time : 0 – 120 Minutes
Programming the Cooldown Temperature
• Limits:
• Cooldown Temperature : 1 - 70 °C
Programming the Motor On and Off times for Reversing
• The standard Reversing Motor On and Off times are 40 Sec-
onds On and 5 Seconds Off.
• Limits:
• Reversing motor on Off times : 3 – 300 Seconds
Programming the anti-wrinkle sequence
• The drum is turning each 2 to 10 minutes for 5 seconds for a
max programmable time of 3 hours.
• A buzzer is beeping when the drum turns.
• Limits:
• Action time Drum : 3 – 180 seconds
• Interval time Drum at rest: 1 – 15 minutes
• Anti-wrinkle time : 15 – 180 minutes
Basic Description of Controls
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
14 Part No. D1621ENR3

Initializing the Machine
Initializing Steps
Initializing the machine goes in four steps:
1. Install the machine mechanically. (See Installation Manual)
FLEX CONTROL :
2. Select the machine specific settings in the Configuration
Menu.
3. Select the operator specific settings in the Initialization Menu.
4. Adjust standard Programs or create new Programs at the Pro-
gram Menu.
WARNING
The initialization should be performed by qualified
personnel only. An incorrect initialization may cause
serious injuries and serious damage to the machine!
C026
WARNING
BEFORE MAKING CHANGES IN THE CONFIGURA-
TION AND INITIALIZATION MENU READ THIS MAN-
UAL CAREFULLY.
CHANGES YOU HAVE MADE WILL INFLUENCE THE
DRYER PROGRAM PROCESSES. WE RECOMMEND
BEFORE MAKING CHANGES TO CAREFULLY WRITE
DOWN WHAT THE PREVIOUS SETTINGS WERE.
AS THE CONTROL DRYER COMPUTER IS USED FOR
A WHOLE RANGE OF DRYERS, AFTER THE INSTAL-
LATION OF A NEW CONTROL DRYER COMPUTER,
YOU NEED TO PROGRAM MACHINE SPECIFIC SET-
TINGS INTO THE CONFIGURATION MENU. Refer to
"Configuration menu".
AT THE INSTALLATION OF NEW SOFTWARE, AFTER
LOADING THE FACTORY SETTINGS (Refer to "Con-
figuration menu") YOU NEED TO CHECK THE DE-
FAULT SETTINGS ONE BY ONE TO FIND OUT IF
THEY CORRESPOND WITH THE SETUP AS YOU
PREFER.
THE CONFIGURATION AND INITIALIZATION OF THE
DRYER HAS BEEN DONE AT THE FACTORY. FOR
THE CREATION OF NEW PROGRAMS, NO CHANGES
HAVE TO BE MADE IN THE INITIALIZATION OR CON-
FIGURATION MENUS.
C110
Initialization Menu
HOW TO GET INTO THE INITIALIZATION MENU
The initialization menu can only be accessed when the machine is
in standby (the power is switched on, but no program is started).
• SELECT PROCESS_ _ is displayed.
• Switch the programming switch Program Mode.
• The Main menu is now available.
• The Initialization Menu is the first Menu and is displayed im-
mediately.
Main Menu Initialization
• Press the ENTER button to make your selection.
• Now you will see the first menu item.
• By pressing the ARROW RIGHT or LEFT button you can see
the menu items one by one.
I:Language: English • Select the preferred Lan-
guage from the list by
pressing the ARROW UP
or DOWN button.
• English is the default set-
ting.
• Press the ENTER button to
confirm.
•English
• Dutch
• Czech
I:View Programs: Ena-
ble Menu ?
I:Enable Program X ?
Yes/No
• The 20 programs can be
enabled or disabled in the
View Programs Enable
Menu.
• If you don‘t want to select
the programs, press the
ARROW RIGHT button.
• If you want to select the
programs, press the EN-
TER button.
• Press the YES or NO but-
ton to Enable / Disable pro-
grams.
• Yes is the default value.
• Yes : the Program is ena-
bled. No : the Program is
disabled.
• Press the ENTER button to
confirm.
Initializing the Machine
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
15 Part No. D1621ENR3

I:Set Unwrinkle Time :
_ _ _ Min
• The Unwrinkle function
avoids that the linen is
wrinkled at the end of the
dry cycle when the opera-
tor has no time to Unload
the machine immediately.
• The unwrinkle time is the
time that the machine will
reverse the fabrics for a
long intermedium time in-
terval.
• The function is switched
OFF for a time setting = 0
minutes.
• Programmable in steps of 5
minutes.
• Limites : 0 – 180 minutes.
• 0 Minutes is the default
value.
• Adjust the value with the
ARROW UP or ARROW
DOWN button and Press
the ENTER button to con-
firm.
• The buzzer will function
each time the mechanical
action is restarted to warn
the operator that the drying
cycle has terminated.
I:Unwrinkle On Time :
_ _ Sec
I:Unwrinkle Off Time :
_ _ Min
• Set the Unwrinkle On and
Off Time.
• Limits :
• On Time : 3-99 seconds
• Off Time : 1-15 mi-
nutes
• Default value : - On Time :
• 5 seconds
• Off Time : 5 minutes
• Adjust the programmed
time with the ARROW UP
and DOWN buttons.
• Press the ENTER button to
confirm.
I:Service Intervall :
3000
• Insert the number of cycles
at which a maintenance is
required. See Installation
and maintenance manual.
• the default setting is :
• 3000
• Press the ENTER button to
confirm.
I:Buzzer Time : 5 Sec • Insert the buzzer time. At
the End of the Dryer cycle,
when the message Unload
is displayed, the buzzer
will function for the pro-
grammed time.
• 5 Seconds is the default
value.
• Press the ENTER button to
confirm.
• The buzzer will function
each time when operator’s
attention is needed.
• The programmable Buzzer
time interval is not applica-
ble in the case of error
messages.
Initializing the Machine
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
16 Part No. D1621ENR3

I:Allow Advance : Yes • With the Advance function
you can Skip a Sequence or
extend & decrease the time
of a Sequence.
• Yes is the default value.
• Yes : the Advance function
is enabled. No : the Ad-
vance function is disabled.
• Press the ENTER button to
confirm.
I:Manual Override : • With the Manual Override
function you can adjust
drying time and tempera-
ture with the special func-
tion buttons when a dry se-
quence is running.
• Yes is the default value.
• Yes : the Manual Override
function is enabled. No :
the Manual Override func-
tion is disabled.
• Press the ENTER button to
confirm.
I:Default Motor Turn
Time : _ _ Sec
I:Default Motor Rest
Time : _ _ Sec
• For programming the ON-
OFF reversing time, the de-
fault values are 40 Sec ON
and 5 Sec OFF. Program-
mable between 3 and 99
sec.
• The purpose of these two
items is to suggest the val-
ues to avoid that the opera-
tor has to insert over and
over again the ON-OFF re-
versing times while pro-
gramming new dryer pro-
grams.
• Press the ENTER button to
confirm.
I:Initialization Menu Exit • You can leave the Initiali-
zation Menu by pressing
the ENTER button.
NOTE: With the ARROW
LEFT button you can go
back to a previous menu
item.
Configuration Menu
This electronic managing system has been specially constructed
for a wide range of dryers. For that reason it must be individually
set up with important parameters for various machine types. Ba-
sic machine adjusting is made in the factory.
WARNING
Only a qualified technician should change the con-
figuration set up. An incorrect configuration can
cause injuries and serious machine damage.
C028
HOW TO GET INTO THE CONFIGURATION MENU
The configuration menu can only be accessed when the machine
is in standby (the power is switched on, but no program is start-
ed).
• SELECT Process_ _ is displayed.
• Switch the programming switch to Program Mode.
• The Main menu is now available.
• Press the ARROW RIGHT button to select the Configuration
Menu.
Main Menu Configuration
• Press the ENTER button to make your selection.
• For the Configuration Menu a Pass-Word is required.
Pass Word _ _ _ _
• Press the 4 function buttons one by one inside the rectangle
and press the ENTER button.
• Now you will see the first menu item.
• By pressing the ARROW RIGHT or LEFT button you can see
the menu items one by one.
C:Machine type
T11
• By pressing the ARROW
UP or ARROW DOWN
button you can select the
machine type.
• Check the Machine data
plate at the rear side of the
dryer machine.
• Press ENTER button to
confirm.
• As a result you will be
asked if you are sure about
your selection. C: Change
Machine type ? No
• Press YES and ENTER
button to confirm once
more.
Initializing the Machine
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
17 Part No. D1621ENR3

• 190 Liters (9kg)
• 250 Liters (11kg)
• 285 Liters (13kg)
• 345 Liters (16kg)
WARNING
BE SURE THAT YOU WANT TO ERASE THE OLD
SETTINGS, AS THEY CAN’T BE RECAPTURED.
CHANGING THE MACHINE TYPE SHOULD ONLY OC-
CUR WHEN A NEW CONTROL DRYER COMPUTER IS
INSTALLED.
C111
WARNING
BE SURE THAT YOU HAVE SELECTED THE COR-
RECT MACHINE TYPE, OTHERWISE THE MACHINE
WILL NOT FUNCTION PROPERLY.
C112
WARNING
BY CHANGING THE MACHINE TYPE THE DRYER
PROGRAMS KEPT IN THE EEPROM MEMORY ARE
NOT CHANGED. AFTER CHANGING THE DRYER MA-
CHINE TYPE IT’S RECOMMENDED TO ERASE THE
PROGRAM MEMORY AND LOAD THE STANDARD
DRYER PROGRAMS AGAIN. THE DRYER PROGRAM
SETTINGS DIFFER FOR EACH MACHINE TYPE.
C113
WARNING
SELECTING RESET FACTORY IS RECOMMENDED IF
A NEW MACHINE TYPE HAS BEEN SELECTED. THIS
WILL ENSURE THAT ALL THE DEFAULT SETTINGS
OF THE NEW MACHINE TYPE ARE LOADED.
C114
C:Reset Factory Set-
tings?
• All the Initialization and
Configuration Menu set-
tings will be cleared and
the default Factory settings
will be re-installed.
• This function should only
be used at the initialization
of a new FLEX CON-
TROL Dryer Computer.
• Select Yes or No and con-
firm by pressing the EN-
TER button.
• By selecting YES , a new
request for confirmation is
displayed C: Delete old
settings ? No
• Press the YES and ENTER
button to confirm once
more.
C:Brightness Display :
9
• You can control the bright-
ness of the display or the
angle at which you have an
optimal contrast by pro-
gramming a value between
1 and 20.
• The default value is 9.
• By pressing the ARROW
UP or DOWN button, you
can adjust the value.
C:Heating Type
Type : HP
• Select the machine heating
system from the list by
pressing ARROW UP or
DOWN button.
• HP (heat pump)
• Press the ENTER button to
confirm.
C:Reversing System :
No
• Set the Reversing function
Yes if the machine type is
executed with Reversing.
• No is the default value.
• Yes : the Reverse function
is enabled. No : the Re-
verse function is disabled.
• Press the ENTER button to
confirm.
Initializing the Machine
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
18 Part No. D1621ENR3

C:Humidity Control
System : No
• Set the Humidity Control
function Yes if the machine
type is executed with Hu-
midity Control.
• No is the default value.
• Yes : the Humidity Control
function is enabled. No :
the Humidity Control func-
tion is disabled.
• Press the ENTER button to
confirm.
C:Temperature: Cel-
cius
• Press the ARROW UP or
DOWN button to select
Celsius or Fahrenheit, de-
pending if you prefer that
the temperature is dis-
played in degrees Celsius
or degrees Fahrenheit.
• Confirm by pressing the
ENTER button.
C:Lint Warning Limit :
15
• The Lint Filter must be
cleaned every day. De-
pending the kind of Fabrics
there will be more or less
lint.
• As memory support, a
warning will be displayed
at the end of the drying cy-
cle if the machine exceeds
the programmed number of
cycles.
• The default value is 15.
• A value between 5 and 20
can be programmed.
• Depending the amount of
lint, you can reduce or in-
crease the number of cy-
cles for which the Alarm
must occur.
• Confirm by pressing the
ENTER button.
NOTE:
By opening the lint door
the „Lint Door Cycle
Counter“ will be reset.
By opening the dryer
door the Warning will be
erased from the display
but will not reset the Lint
Door Cycle Counter.
If the „Lint Door Cycle
Counter“ has not been
reset for 40 cycles, an
Error message will be
displayed and the ma-
chine can’t be started
anymore until the error
message is reset by the
programming switch.
Initializing the Machine
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
19 Part No. D1621ENR3

C:Erase All Programs? • You can erase all the dryer
programs at once.
• This function should only
be used at the installation
of a new FLEX CON-
TROL Dryer Computer
and if you want to ensure
that no old programs stay
in the memory of the com-
puter.
• For all 20 programs default
values will be loaded.
• Select Yes or No and you
have to confirm by press-
ing the ENTER button.
• By selecting YES , a new
request for confirmation is
displayed. C: Delete all
Programs ? No
• Press YES and ENTER
button to confirm once
more.
Initializing the Machine
© Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
20 Part No. D1621ENR3