ALTAI CX200 User manual

1
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Altai CX200 Outdoor 2x2
8 0 2 . 1 1 a c W a v e 2 AP
_________________________________________________
Quick Setup Guide
Version 2.0

2
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Introduction
Thank you for purchasing the Altai CX200 product. This guide provides
instructions to install the product and set it up as AP with minimal effort.
Package Contents
Adhesive Label
Wall Mount Kit
-
Anchors x 2
-Screws x 2
Pole Mount
Hose Clamp
CX200 Main Unit
Quick Setup Guide
Detachable Antennae
-
2.4GHz Antenna x 2
-5GHz Antenna x 2
PoE Injector
(Optional)

3
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Hardware Overview
LED Indicator
Power
Off
AP powered off
Flashing Red
AP booting up
Solid Red
AP boot up finished and ready for
service
LAN (Ethernet)
Off
LAN disconnected
Solid Green
LAN connected
Flashing Green
Data Transmitting/Receiving
2.4GHz/5G WiFi
Radios
(AP/Station/
Repeater/Bridge)
Off
Radio Disabled
Solid Green
1. AP mode on but with no client
association; OR
2. Station mode on but not
connected to remote AP; OR
3. Repeater mode on but not
connected to remote AP; OR
4. Bridge mode on but not
connected to remote peer
Flashing Green
Data transmitting/receiving
LED Indicator

4
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Ethernet Port and RF Antenna Port
Ethernet Port:
Used to connect to power source (see the Power Options in the later section)
and provides 10/100/1000 Mbps network interface for LAN connection.
RF Antenna Ports:
Used to attach 2.4G and 5G antennae for 2x2 MIMO WiFi access coverage or
bridge connection.
Ethernet Port
5GHz Omni
Antenna
5GHz Omni
Antenna
2.4GHz Omni
Antenna
NOTE: To ensure correct
antenna connection, check
the labels (2.4GHz/5GHz)
printed on each antenna
body and RF port for easy
reference.
2.4GHz Omni
Antenna

5
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Setup Preparation
•Wire stripping tool and crimping tool
•Screwdriver (Slot type and Phillips type)
•Drill and drill bits
•Computer with Web Browser: Google Chrome, Mozilla Firefox, or Microsoft
Internet Explorer 8 (or above)
•Two Cat 5e/6 Ethernet cables
•802.3af-compliant PoE switch
•AltaiCare account (if applicable) for centralized WiFi management
Ethernet Cable Feed-Through
Seal the RJ45 cable Connector with the provided cable gland.
1
Feed the end of the cable
through the cap nut, sleeve
holder, sealing sleeve as
shown in the picture.
3
Connect the cable to the
Ethernet Port.
Cap Nut
RJ45 Connector
Sealing Sleeve
Sleeve Holder
4
Tighten the cap nut.
2
Crimp the Ethernet
connector with the crimping
tool.

6
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Mounting Options
Option 1: Pole Mount (For 1.5 to 2.5 inches of pole diameter)
Option 2: Wall Mount
2
Determine where the AP is to be placed. Tighten the hose clamp to
secure the base to the pole.
1
Thread the open end of the hose clamp through the two slots of the
mount base.
1
2
1
2
3
4

7
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Power Options and Cable Connection Instructions
Follow one of the options below to power up the CX200 for configuration.
Option 1: PoE Injector (purchased separately)
1. Connect the PoE injector ports as described below via Ethernet Cables.
-PoE Port: Go to the CX200
-LAN Port: Go to a computer
2. Connect the PoE Injector to AC power socket using a power cord.
3. Make sure the Power LED turns into a solid light for AP configuration.
2
Use an appropriate drill bit to drill two holes, each with 1/3”(8.1mm) in
diameter and 1”(26mm) deep, on the markings.
Determine where the AP is to be placed and use the adhesive label to
mark location of the two mounting holes on the wall surface.
1
Remove the label. Drive the anchors into the holes and then the screws
into the anchors.
3
Align the mounting slots with the screw heads and attach the AP to the
wall in place.
4
PoE
LAN
PoE Injector

8
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Option 2: 802.3af-Compliant PoE Switch
1. Connect the CX200 Ethernet port to an 802.3af-compliant PoE switch with
an Ethernet Cable.
2. Connect a computer to the switch.
3. Make sure the Power LED turns into a solid light for AP configuration.
Factory Reset
Besides the software-based reset via AP WebUI, there are the two options to
restore the CX200 to factory default settings.
Option 1: Using Reset Button of PoE Injector
1. Power up the CX200 with the PoE injector as
illustrated in the power option #1 above.
2. Locate the Reset Pin Hole on the injector.
3. Insert a sharp-pointed object, e.g. paper clip,
into the hole and press for 10-20 seconds.
Option 2: Using AP Factory-Reset Tool
For details, please visit https://www.altaitechnologies.com/tools-and-
utilities/
Reset
Pin Hole
802.3at –Compliant
PoE Switch

9
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
1. Change TCP/IP Setting on Your Computer
For Windows 7/Windows 10 users,
1. Go to Control Panel, click Network and Sharing Center and then choose the
Ethernet adapter that is in connection with the CX200 unit. Click it and then
click Properties.
2. Under the Networking tab, select Internet Protocol Version 4 (TCP/IPv4) in
the list box “This connection uses the following items”, and then click
Properties.
3. Type in the following IP address and Subnet mask:
•IP address: 192.168.1.2
•Subnet mask: 255.255.255.0
4. Click OK to close the Internet Protocol Version 4 (TCP/IP) Properties dialog
box and click OK again to close the adapter Properties dialog box.

10
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
2. Access to Web Interface
1. Open a web browser. Type 192.168.1.222 in the address bar and then hit
Enter.
2. Login page will come up and you are required to enter username and
password. By default, the credentials are:
•Username: admin
•Password: admin
3. Click Login.

11
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
3. Configure AP Mode (2.4G/5G)
Network Scenario
Go to Configuration > Wireless > Radio0(2.4G)/Radio1(5G) > General. Below
screenshots show an example for 2.4G radio configuration only. Same
procedures can be applied to 5G radio configuration.
1. Check the box to Enable Radio. Select AP in the Radio Mode field. Then
click Submit button.
ISP
Modem
Gateway/Router
Internet
Modem
Cable
Ethernet
Cable
Ethernet
Cable
2.4G + 5G
Coverage
CX200
(AP Mode)

12
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
2. Click WLAN tab on the navigation bar. Check the box to Enable WLAN 0
and enter the SSID to name the wireless network you want to advertise, e.g.
Altai CX200.
3. To secure the network, it is recommended to use WPA2 Personal or WPA2
Enterprise for client connection. For simplicity, select WPA2 Personal in the
drop down menu of Auth Mode and enter a string of 8-64 characters long
for Passphrase. Then click Submit button.
4. Click Save & Apply in the top right corner to have all changes take effect.
5. Hook up the CX200 as in the Network
Scenario. The SSID should now be broadcast
from it and be seen in the computer for
wireless connection.

13
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
4. Connect with Cloud-Based Controller –AltaiCare
Network Scenario
You can opt for AltaiCare cloud-based platform to manage a group of your
APs anywhere, anytime. Follow the steps below to join your AP to the system.
1. Go to Configuration > Network > General. Select Switch Mode for Network
Setting. Make sure the CX200 can reach Internet and communicate with
AltaiCare by giving valid IP settings either via DHCP or with Static IP
configuration. You can use Google Public DNS Server, e.g. 8.8.8.8 or 8.8.4.4,
if not sure about your ISP DNS’s Server IP.
CX200_1 (AP)
CX200_2 (AP)
ISP Modem
Local Gateway/
Router

14
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
2. Click Remote Mgmt tab on the navigation bar. Check the box to Enable
Remote Management. Select AltaiCare as Management Type and Cloud
as Connection Type.
3. Select Full Management if the radio (2.4G/5G) is running on AP Mode. If
Station Mode, Bridge Mode or Repeater Mode, select Monitor Mode instead.
4. Click Submit button and then Save & Apply in the top right corner to make
all the changes take effect.
5. Follow AltaiCare Quick Start Guide to register the CX200 in the cloud system.
6. The CX200 will come up online in AltaiCare if the connection is successful.

15
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Federal Communication Commission Interference Statement (FCC) –USA
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 36cm between the radiator & your body.
European Conformity (CE) –EU
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case
the user may be required to take adequate measures.

16
Altai Technologies Ltd. All rights reserved
Quick Setup Guide
Warning
CX200 may require professional installation depending on the deployment scenario.
Only use the power adaptor supplied with CX200. Using a different power adaptor might damage the device.
Disclaimer
All specifications are subject to change without prior notice. Altai Technologies assumes no responsibilities for
any inaccuracies in this document or for any obligation to update information in this document. This
document is provided for information purposes only. Altai Technologies reserves the right to change, modify,
transfer, or otherwise revise this publication without notice.
Copyright © 2020 Altai Technologies Limited
ALL RIGHTS RESERVED.
Altai Technologies Limited
Unit 209, 2/F, Lakeside 2,
10 Science Park West Avenue,
Hong Kong Science Park,
Shatin, New Territories,
Hong Kong
Telephone: [phone]
Fax: [phone]
Web: www.altaitechnologies.com
Customer Support Centre:
Email: [e-mail]