Aluprof DC 448 Owner's manual

1
DC 448 PROGRAMMING MANUAL
We reserve the right to any technical change. Valid on 2019.03.13
1. TECHNICAL SPECIFICATIONS
DC 448 PROGRAMMING MANUAL
OK / K+ OK / K+
STOP
P2 SET OK / K+
MODE / K-
433 MHz
AC
230V / 50Hz
- Individual 5 channel control
- E ach channel can control maximum 20 receive rs
- Key lock function
- LCD display
- Dimensions: 80x80 mm
- Power supply: 2 x 3V (CR2430)
- Frequency: 433.92 Mhz
- Radiated power: 10 miliwat (mW)
- Operating temperature: ~ -20°C ~ +55°C
- Average range: 200 meters (in open space)
35 meters (inside buildings)
In accordance with the provisions of the Directive of the European Parliament and of the Council 2012/19 / EU of 4 July 2012 on waste electrical
and electronic equipment (WEEE), it is prohibited to place of used equipment together with other wastes, marked with crossed out wheeled bin
symbol. The users are obliged to transfer their used equipment to a designated collection point for proper processing. The marking means,
at the same time, that the equipment was put on the market after 13 August 2005. These legal obligations have been introduced to reduce the
amount of waste generated from waste electrical and electronic equipment and to ensure an appropriate level of collection, recovery and recycling.
The equipment does not contain any dangerous components, which would have any particularly negative impact on the environment
and human health.
ClockBattery Active channel
Control: The Directions
Number of
Active days in
- Manual of movement
the automatic
auto mode
- Auto
control mode
Company reserves the tolerance of catalog data due the different
conditions usage.
In the auto mode interval between rollup and roll down time
cannot be less than 32 minutes, otherwise the display will show
“ER:01”
In the automatic settings, it is possible to deactivate one or more
channels from the automatic mode by placing the cursor on the
specified channel and holding down the„OK / K +” button for
approx. 3 seconds, which causes the channel symbol to flash.
The control changes are made only in automatic or random
transmission mode.
If the operation distance of the transmitter will drop you should
replace the battery.
Works with tubular motor`s DM35R, DM45R, DM45RM, DM55RM,
DM59RM, DM35EV/Y, DM45EV/Y
Operation of the„UP” or„DOWN” key in the automatic control
mode allows the display of the currently programmed raising or
lowering time as well as displaying the symbol of the executed
command
- Random

2
DC 448 PROGRAMMING MANUAL
We reserve the right to any technical change. Valid on 2019.03.13
Hold the„SET P2” button for 2
second will switch the transmitter
to the ‘MAN’ mode.
Then press the„P2”button for two
seconds. The transmitter switches to
the automatic control mode„AUTO”
The next press of the„P2” button
for two seconds will switch the
transmitter to random control mode
2.2. Key lock function
Hold the „OK/K+” and„MODE/K-„
for 3 seconds to active the key lock
function.
if any button on the transmitter is pressed
while the keypad lock is activated, the
information„LOCK” is displayed on the
transmitter display.
If key lock function is active, hold the
„OK/K+” and „MODE/K-„ for 3 seconds to
deactivate the key lock function.
2.1. Operating mode change
2. PROGRAMMING THE TRANSMITTER

3
DC 448 PROGRAMMING MANUAL
We reserve the right to any technical change. Valid on 2019.03.13
2.2. Setting of the timer
Programming of the timer can be performed only in ‘MAN’ mode.
If there will be a bigger interval during the programming than 10 seconds the timer will go from the setting mode out.
With the help of the „OK / K +” - buon
we conrm all changes
Hold the„SET P2” button for 2 second will
switch the transmitter to the‘MAN’mode.
Hold the „MODE/K-” buon for 5 seconds
ll the hour will blink
The operaon of the „UP” and „DOWN”
keys changes the hour sengs
The operation of the„UP” and„DOWN”
keys changes the minute settings
Press the„MODE/K-” to confirm
the minute.
The operation of the„UP” and„DOWN”
keys changes the day of the
week settings
With the help of the„OK / K +”
- button we confirm all changes

4
DC 448 PROGRAMMING MANUAL
We reserve the right to any technical change. Valid on 2019.03.13
2.3. Settings days and hours for automatic controls
Programming of the timer for the automatic controls can be performed only in automatic or random mode.
If there will be a bigger interval during the programming than 10 seconds the timer will go from the setting mode out.
Hold down the „MODE / K”
buon for 5 seconds to display the hour
symbol (raise).
Press and hold the „P2” buon for 2
seconds to switch the automac control
mode to the random control mode
Press the „MODE / K -” key again so that
the hour symbol starts to ash.
The operaon of the „UP” and „DOWN”
keys changes the hour sengs
By pressing the„MODE / K-”-button you
can change to the minutes settings
The operation of the„UP” and„DOWN”
keys changes the day of the week
settings.
The operation of the ”UP” and„DOWN”
keys changes the minute settings
By pressing the„MODE / K-”-button you
can switch to changes in the weekday
settings
By pressing the „OK / K +” buon we
conrm the changes and go to the
sengs of the reducon mes
The operation of the ”UP” and„DOWN”
keys changes the minute settings
The operaon of the „UP” and „DOWN”
keys changes the hour sengs
By pressing the„MODE / K-”-button you
can change to the minutes settings
Press the „OK / K +” buon to accept and
save all the changes you have made and
at the same me go to the sengs of the
next sender channel
When all the necessary changes have
been made and the seng funcon has
to be exited then we press the „Stop”
buon which switches the transmier to
the operang control mode.