Aluprof DC1675 Installation manual

1
We reserve the right to any technical change.
Valid on 2022.02.09
PROGRAMMING INSTRUCTIONS FOR THE WALL TRANSMITTER: DC1675 AND DC1676
1. TECHNICAL SPECIFICATIONS
Power supply:
Operating temperature:
DC1675 - 1-channel:
230 VAC / 50 Hz
~ -10°C - ~ +55°C
Average range: 200 meters (in open space), 35 meters (inside buildings)
Frequency: 433.92 MHz
Company reserves the tolerance of catalog data due the different conditions usage.
In accordance with the provisions of the Directive of the European Parliament and of the Council 2012/19 / EU of 4 July 2012
on waste electrical and electronic equipment (WEEE), it is prohibited to place of used equipment together with other wastes,
marked with crossed out wheeled bin symbol. The users are obliged to transfer their used equipment to a designated collection
point for proper processing. The marking means, at the same time, that the equipment was put on the market after 13 August
2005. These legal obligations have been introduced to reduce the amount of waste generated from waste electrical and
electronic equipment and to ensure an appropriate level of collection, recovery and recycling. The equipment does not contain
any dangerous components, which would have any particularly negative impact on the environment and human health.
It is compatible with all the DM series radio controlled motors and DC series control units from ALUPROF S.A. offer.
Activation of the “P2” button in DC1675, DC1676 wall transmitters is performed by a combination of both keys “MODE” and “K+”.
Possibility to control 1 motor or 1 group of motors.
DC1676 - 5-channels:
Possible of control of 5 motors or 5 groups of motors.
2. DIAGRAM OF THE FRONT PANEL
UP
STOP
DOWNK-
MODE
K+
Discharged battery
Roller shutter move - UP
Roller shutter move - down
Clock
Week days
Active channel
Operating mode
PROGRAMMING INSTRUCTIONS FOR THE WALL TRANSMITTER: DC1675 AND DC1676

2
We reserve the right to any technical change.
Valid on 2022.02.09
PROGRAMMING INSTRUCTIONS FOR THE WALL TRANSMITTER: DC1675 AND DC1676
4. ACTIVE CHANNEL SELECTION
Switch to automatic or
random mode.
Select the chosen channel. Hold down the “K-”button
for 3 seconds, digits of the disabled
Holding the “K-”button again
for 3 seconds turns on the
channel will flash. selected channel.
3. OPERATING MODE CHANGE
Press and hold the“MODE”
button for 3 seconds. The mode
By reapitting procedure
will be changed.
will change mode between:
“Manual”,
“Automatic”,
“Random”.
Manual mode - without time control function,
Automatic mode - with time control function,
Random mode - with time control function with a random selected time within ± 15 minutes to the set automatic time.
The function only applies to the DC1676 transmitter. By default, all channels are active.

3
We reserve the right to any technical change.
Valid on 2022.02.09
PROGRAMMING INSTRUCTIONS FOR THE WALL TRANSMITTER: DC1675 AND DC1676
5. SETTING OF THE CURRENT TIME
Switch to manual mode
Press and hold“K+”button By pressing the ”UP” or “DOWN”
buttons, settings of the
Press“K+”button. Minutes
digits will flash.
for 3 seconds. Hour digits will
flash. minutes can by change.
Press “K+” button. Week By pressing the ”UP” or “DOWN”
buttons, settings of the
To approve entered changes
press and hold “K-”button for 3
day will flash. week days can by change.
By pressing the ”UP” or “DOWN”
buttons, settings of the
minutes can by change. seconds.
Press the“K +”button to
start the clock.
Saving changes will be
confirmed by three flashys of the
hour and minute digits.

4
We reserve the right to any technical change.
Valid on 2022.02.09
PROGRAMMING INSTRUCTIONS FOR THE WALL TRANSMITTER: DC1675 AND DC1676
6. SETTING OF THE AUTOMATIC CONTROL TIME
Switch to automatic or Press and hold“K +”button Press the“K +”button again. Hour
digits will flash.
Press the“K-”button to
select the day of the week.
for 3 seconds. The lifting hour will
be displayed.
Press “K+” button. By pressing the ”UP” or “DOWN”
buttons, settings of the
Press the“MODE”button. The
lowering hour will be displayed.
Minutes digits will flash.
minutes can by change.
By pressing the ”UP” or “DOWN”
buttons, settings of the
minutes can by change.
Hour digits will flash.
random mode.
Press “K+”button.
Press the“K-”button to
switch to the setting of the
Minutes digits will flash.
next day.
Press and hold the“K-”
button for 3 seconds to save
the changes made.
By pressing the “UP” or “DOWN”
buttons the settings for each day
By pressing the “STOP” button procedure can be canceled.
of the week can be display.
Repeat the above steps to set
the hours for other days.
Saving changes will be
confirmed by three flashys of the
hour and minute digits.
The symbol “- - : - -” in the automatic control time settings means that the control is not active.
To automatically control receivers from all the channels seting up a group channel on the transmitter is required. Group
channel is active when all channels numbers are highlighted.
In the auto mode interval between lifting and lowering time cannot be less than 32 minutes, otherwise the display will show
“ER:01” error.
By pressing the ”UP” or “DOWN”
buttons, settings of the
minutes can by change.
By pressing the ”UP” or “DOWN”
buttons, settings of the
minutes can by change.