Amano PIX-15 User manual

PIX-15
Electronic Time Recorder
Operation Manual

Thank you…
for purchasing another fine product from
Amano Cincinnati, Inc.
Important
Note that the government standard for Daylight Saving Time (DST) is
subject to change. Your clock is factory-set for correct DST based upon
when it was manufactured, but any revision to DST begin or end dates
may require updating the system-set DST calendar.
If you live in Arizona, Hawaii, parts of Indiana, or any other area that
does not use Daylight Saving Time, refer to this document’s DST
settings instruction for details regarding disabling the DST function.
Do not return this clock to the retailer. If you have any questions or need
assistance, please call us toll free at:
1-800-253-9836
Proprietary Notice
This document contains proprietary information and such information
may not be reproduced in whole or part without the written permission
from Amano Cincinnati, Inc. 140 Harrison Ave., Roseland, New Jersey
07068. Amano Cincinnati, Inc. reserves the right to make equipment
changes and improvements, which may not be reflected in this
document.
We recommend that this document be read in its entirety before any
attempt is made to operate the equipment.
Need Ribbons, Keys and Accessories?
Visit
www.amano.com
or
Call - (800)-253-9836

Amano PIX-15 Operation Manual 1
Your PIX-15
Removing the Cover and Packing Materials
Note: You must remove the packaging spacers from the printer block and the
printer carriage before attempting to use your PIX-15.
1. Lift the printer block and remove the spacer.
Ke
y
hole
Print Window
Digital Clock
Print
Margin
Reset Switch
(on bottom)
Change
Button
Enter
Button
Print Slot
Spacer
Printer
Block
Spacer

2 Amano PIX-15 Operation Manual
2. Insert the key provided and turn clockwise to open the case. Lift
the cover to remove.
3. Remove the spacer between the Ribbon Cartridge and the Printer
Carriage.
4. Re-install the cover. Your PIX-15 is ready for use!
O
p
en
Closed
Remove
Spacer

Amano PIX-15 Operation Manual 3
Before You Change Any Settings
Take a moment to familiarize yourself with the items explained below.
The Front Panel
LCD Display Window CHANGE Button ENTER Button
Normally, the Display Window shows the date and time. When you use
the Quick Set or Program Mode to change the settings of the PIX-15, the
instructions to change the clock are shown in this window.
The two buttons on the front panel are used to navigate through the
Quick Set and Program Mode to change the clock’s settings.
The left button is marked with a ◄symbol. It is called the
CHANGE Button. Use this button to change the information shown on
the display when you are in the Quick Set or Program Mode.
The right button is marked with a ●symbol. It is called the
ENTER Button. When you are in the Quick Set or Program Mode, use
this button to enter the setting shown on the display into memory.
The Reset Button
The RESET Button (which
is long) is located in the
right lower corner on the
bottom of the clock.
Please Note:
You do not need the key to set the time or to program the clock!!
However, you do need the key to change the ribbon, or mount the clock
on the wall (see page 9).
If you have any questions, please call 1-800-253-9836.

4 Amano PIX-15 Operation Manual
Making a Test Print
1. Plug in the power cord.
2. Insert a piece of paper or time card into the PIX-15. The clock will
automatically print YEAR, MONTH, DATE and TIME with AM or PM
(in Pacific Time).
Note: The PIX-15 will automatically adjust for Daylight Saving Time. If these
conditions are unsatisfactory, you must change the program settings.
3. If the imprint is satisfactory, and you are going to place the PIX-15 on
a desk, table, or shelf, the PIX-15 is ready to be used.
4. In order for you to set the time or change the print style, you must
enter a code. Choose a code from the list below that best fits your
needs. Continue to the next page for instructions on how to enter your
code.
Code Print Style Print Direction
6510 DAY, 12H, 60th Right Side Printing
6210 DAY, 24H, 10th Right Side Printing
6810 DAY, 24H, 100th Right Side Printing
6520 DATE, 12H, 60th Right Side Printing
6620 DATE, 24H, 60th Right Side Printing
6820 DATE, 24H, 100th Right Side Printing
6530 MONTH, DATE, 12H, 60th Right Side Printing
6630 MONTH, DATE, 24H, 60th Right Side Printing
6830 MONTH, DATE, 24H, 100th Right Side Printing
6570 YEAR, MONTH, DATE, 12H, 60th Right Side Printing
6071 YEAR, MONTH, DATE, RCV’D Right Side Printing
6072 YEAR, MONTH, DATE, SENT Right Side Printing
6073 YEAR, MONTH, DATE, FAX’D Right Side Printing
6074 YEAR, MONTH, DATE, VOID Right Side Printing
6075 YEAR, MONTH, DATE, PAID Right Side Printing
6076 YEAR, MONTH, DATE, CFM’D Right Side Printing
6077 YEAR, MONTH, DATE, APR’D Right Side Printing
6078 YEAR, MONTH, DATE, CMPL’D Right Side Printing
6079 YEAR, MONTH, DATE, ORIGN Right Side Printing
6070 YEAR, MONTH, DATE, FILE Right Side Printing
Note: If you cannot locate the desired print style from the above list, please
contact us at 1-800-253-9836 for assistance.

Amano PIX-15 Operation Manual 5
Entering the Clock Program
The following steps describe how to get into the clock program. To set
the print style and time, use a code chosen from the list (see page 4).
For example, the following directions use code 6570.
1. Entering a Code
a. Press and hold the RESET button on the bottom of the
clock. (Refer to page 3 for location.)
b. While holding down the RESET button, press and hold
the ●right button on the front panel.
c. While holding the ●right button, release the RESET
button.
d. Next release the ●right button and Pro9 will
flash in the display.
e. Tap the ●right button. The display will show
0000, and the first digit will flash.
f. Tap the ◄left button until the first number of
your code appears, then tap the ●right button
and the second digit will flash.
g. Tap the ◄left button until the second number
of your code appears, then tap the ●right
button and the third digit will flash.
h. Tap the ◄left button until the third number of
your code appears, then tap the ●right button
and the fourth digit will flash.
i. Tap the ◄left button until the fourth number of
your code appears, then tap the ●right button.
j. With the display flashing all four digits,
tap the ●right button again and Pl dA Ewill display.

6 Amano PIX-15 Operation Manual
2. Setting the Year, Month and Date
a. With the display flashing Pl dA E,
tap the ●right button and the display will show
year, month, and date.
b. Press the ◄left button until the correct year
appears, then tap the ●right button.
c. Press the ◄left button until the correct month
appears, then tap the ●right button.
d. Press the ◄left button until the correct date
appears, then tap the ●right button.
e. When the display flashes the correct year, month
and date, tap the ●right button.
f. When the display flashes Pl dA E, tap the
◄left button to move to Setting the Time
(P2 CLoc will display)
3. Setting the Time
When setting the time, you must use a 24 hour and 60 minute format
(i.e., 1:00 pm = 13:00). This will NOT make the clock print in
military time, but simply tells the clock am from pm.
a. With the display flashing P2 CLoc, tap
the ●right button.
b. The small “12” will flash. Tap the
●right button again.
c. The hour digits will flash. Tap the
◄left button until the correct hour
appears. Remember to use a 24-hour
format (2:00 pm = 14:00). Then tap the
●right button.
d. The minute digits will flash. Tap the
◄left button until the correct minutes
appear, then tap the ●right button.
e. When the display flashes P2 CLoc, tap the
◄left button to move to the beginning of
the Daylight Saving Setting (P3 bdLt will display).

Amano PIX-15 Operation Manual 7
4. Setting the Beginning Date of Daylight Saving Time (DST)
Note: The government standard for DST is subject to change. Your clock is
factory-set for correct DST based upon when it was manufactured, but any
revision to DST begin or end dates may require updating the system-set
DST calendar.
The steps below change the begin date for DST. Updating the begin date
for DST needs to be done just one time*, since the clock’s rolling calendar
function will auto-calculate the begin date for each year thereafter. To
change the end date for DST, refer to the next section.
a. With the display flashing P3 bdLt, tap the
●right button.
b. Tap the ◄left button until the correct year
appears, then tap the ●right button.
c. Tap the ◄left button until the correct month
appears, then tap the ●right button.
d. Tap the ◄left button until the correct date
appears, then tap the ●right button.
e. With the display flashing the correct year, month
and date, tap the ●right button.
f. With the display flashing P3 bdLt, tap the
◄left button to move to the end of the Daylight
Saving Setting (P4 EdLt will display).
5. Setting the End Date of Daylight Saving Time (DST)
Note: The government standard for DST is subject to change. Your clock is
factory set for correct DST based upon when it was manufactured, but any
revision to DST begin or end dates may require updating the system-set
DST calendar.
The steps below change the end date for DST. Updating the end date for
DST needs to be done just one time, since the clock’s rolling calendar
function will auto-calculate the end date for each year thereafter. To
change the begin date for DST, refer to the previous section.
a. With the display flashing P4 EdLt, tap the
●right button.
b. Tap the ◄left button until the correct year
appears, then tap the ●right button.
c. Tap the ◄left button until the correct month
appears, then tap the ●right button.

8 Amano PIX-15 Operation Manual
d. Tap the ◄left button until the correct date
appears, then tap the ●right button.
e. With the display flashing the correct year, month
and date, tap the ●right button.
f. With the display flashing P4 EdLt, tap the
◄left button to move to the end of the Program
(End will display).
Note: To disable the Daylight Saving Setting, set the beginning and
ending date to the same date.
6. Exiting the Program Mode
When the display flashes End,tap the ●right button to
exit the program mode.
7. The PIX-15 is ready for use!
Note: If you do not use Daylight Saving Time, you need to disable the Daylight
Saving Time feature. Putting the same dates in program level P3 and P4
does this. If you need assistance or have any questions, please contact us
at 1-800-253-9836.
*Note:The PIX-15 uses a Lithium battery to maintain the user settings incase of
a power failure. If a power failure occurs and the Lithium battery is dead,
the time clock settings may revert to default settings (i.e., DST Begin and
End dates may change).

Amano PIX-15 Operation Manual 9
Replacing the Ribbon
1. Insert the key into the key hole (see
page 2 for keyhole location) and turn
the key.
2. Grab the cover on both sides and lift
to remove it.
3. Pull the two catches (B) upward and
hold them with your index and
middle fingers. Remove the ribbon
cassette.
Note: If the print mechanism is in the down position and a piece of paper
cannot be inserted, press the RESET button to move the carriage up.
This will make the ribbon installation easier.
4. Insert a new ribbon between the ribbon guide (C) and the printer
head (D).
5. Turn the knob on the cassette clockwise one turn to take up any
slack in the ribbon.
6. To replace the cover, remove the key, align the lower back corners
to the base of the clock and snap the cover down into position.

10 Amano PIX-15 Operation Manual
Mounting the Clock
1. Remove the cover as per the instructions above.
2. With the clock facing you, remove the mounting bracket by pulling
the top tabs (A) towards you, and then pushing the tabs down (see
below).
3. Securely mount the PIX mounting bracket on the wall using three
#10 wood screws or equivalent.
4. Place the PIX-15 on the Mounting Bracket by sliding the top tabs into
the slots on each side of the case. Push the PIX-15 back and down
against the Mounting Bracket until the PIX-15 snaps into place. Be
careful not to pinch the power cord with the bracket. Installing the
cover will secure the PIX-15 to the mounting bracket.
Printer
Frame
Wall
Mounting
Bracket

Amano PIX-15 Operation Manual 11
Error Messages
If any of these messages appear on the display, unplug the clock from
your outlet then plug it back in again. If the message still appears on your
display, please contact us at 1-800-253-9836 for assistance.
CAUTION:
Do not use any chemical solvents or oils to clean or lubricate your
PIX-15. This will damage your clock. To clean the inside of your clock,
blow it out with air.
Home Sensor,
Motor Carriage
Stuck
Timing Sensor,
Motor Carriage
Stuck
Home Senso
r
Carriage Stuck General
Print Error
Daylight
Saving Time
Program

12 Amano PIX-15 Operation Manual
Specifications
Power Requirements: For PIX-15 Input: AC16.5V, 60Hz, 0.6A (Max.)
For AC Adapter: AC120V ± 10%, 60Hz
AC230V ± 10%, 50Hz
AC240V ± 10%, 50Hz
Ambient Temperature: -10°C to 45°C (14°F to 113°F)
Ambient Humidity: 10% to 90% (no condensation)
Dimensions: 140mm (W) x 150mm (H) x 165mm (D)
(5½" x 6" x 6½")
Weight: 1.8Kg (4.2Lbs.)
Environment: Indoor use only; dust-free environment
Keep out of direct sunlight
PIX-15 with 120V AC Adapter:
Listed and Certified by Underwriters Laboratories, Inc.

AJR-211902 •Copyright © 2007 Amano Cincinnati, Inc. •1/07/0