AMP Lighting APL-3031-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® G2 ArchPro Path & Area Light
APL-3031-B-BZ

AMP®G2 ArchPro Path & Area Light
APL-3031-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the war-
ranty.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply (transform-
er) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with UL Listed wire connectors that
are suitable for the application.
6. Position the wire connector so that it is located within 6 inches (15.2
cm) from a building structure, a luminaire, or tting.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.

[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
A. (1) Fixture Body
Parts Required
A. (1) Mounting Accessory
B. (1) GU4 Bi-Pin
24.43”
3.39”
5.44”
11.81”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
1
AMP®G2 ArchPro Path & Area Light
APL-3031-B-BZ
Remove Lens
Loosen the lens and remove it
from the xture body.
Fixture Body
Lens
Install Bulb
Insert the bulb with the correct
wattage and type marked on the
xture label and push into place.
CAUTION: Do not exceed maxi-
mum wattage marked on xture
label.
Socket
Bulb
3
Install Lens
Thread the lens back onto the x-
ture body and hand tighten until
snug.
Fixture Body

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
Install Stake
Install Fixture to Stake
AMP®G2 ArchPro Path & Area Light
APL-3031-B-BZ
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake is
ush to grade. To avoid damage
to the stake, place a board on
top of the stake while hammer-
ing.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake
Pass the supply wires through
the center hole of the stake
and thread the stem onto
the stake. Hand tighten until
snug. Clear away an area in
the ground and lay the supply
wires into the wireway slot.
Ground
Stem
Supply Wires
Soil
Stake

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
6
Wire Connections
AMP®G2 ArchPro Path & Area Light
APL-3031-B-BZ
Strip both leads from the xture wires. Using two UL listed wire connec-
tors (sold separately), connect the leads from the xture wires to the
main supply cable leads.
Main Supply Cable
Fixture Wires
Wire Connectors
7
Adjust Shade Direction
There are two methods to adjust the shade direction.
NOTE: Do not rotate the shade a full 3600. This will damage the internal
wiring.
A. Loosen the knuckle on the stem to adjust the shade to your desired
angle. Once your desired angle is achieved, hand tighten the knuckle
to secure the shade direction.
B. Using the Allen wrench, loosen the set screw on the stem and adjust
the shade to your desired angle. Once your desired angle is achieved,
tighten the set screw using the Allen wrench to secure the shade
direction.
Shade
Shade
Knuckle Allen Wrench Set Screw
ROTATE
OPTION A OPTION B
ROTATE

[email protected] • 813.978.3900
–7–
Install/Replace Bulb
Reverse Step 2 - Step 3 to expose the bulb and replace it with the correct
wattage and type marked on the xture label. Then, reinstall the lens.
IMPORTANT: The bulb must be protected from moisture and dust at all
times. Always reinstall the lens when removed.

IS-APL-3031-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2021, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com