AMP Lighting BeaconPro Path & Area Light Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® BeaconPro Path & Area Light
APL-3030-4-B-BZ

AMP®BeaconPro Path & Area Light
APL-3030-4-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and in-
structions may result in serious injury, property damage and void the warran-
t y.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used at 12V/AC.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and UL listed wire connector so that it is
located within 6 inches (15.2 cm) from a building structure, a luminaire
or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may dam-
age lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3900
–3–
Package Contents
A. (1) Fixture Body
Parts Required
A. (1) Mounting Accessory
B. (1) Flame Lamp
C. (1) SCB Lamp (sold separately)
Product Dimensions
10.75”
8”
6”
25”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
1
AMP®BeaconPro Path & Area Light
APL-3030-4-B-BZ
Remove Hat Bottom
Remove the bottom of the hat,
by using a screwdriver to loosen
the screws.
Hat Top
Hat Bottom
Screws
Install Flame Lamp
Install the ame lamp by aligning
the line on the bottom of the lamp
to the holes in the socket. Once it
is aligned, gently push the ame
lamp into the socket
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
Socket
Flame Lamp

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
3
4
AMP®BeaconPro Path & Area Light
APL-3030-4-B-BZ
Reinstall Hat Bottom
Reinstall the hat bottom using
the previously removed screws.
Use a screwdriver to make sure
the screws are secure.
Hat Top
Hat Bottom
Screw
Remove Lens
Remove the lens on the bot-
tom of the hat by loosening the
screws using a screwdriver.
Lens
Hat
Screw
5
Use SCB lamp with correct wattage
and type marked on xture label.
Align the bayonet base of the SCB
lamp to bayonet socket. Insert the
SCB lamp into the bayonet socket and
twist it until the SCB lamp is inserted
properly.
CAUTION: Do not exceed
maximum wattage marked on lumi-
naire label.
SCB Lamp
Bayonet Socket
Install SCB Lamp

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
6
AMP®BeaconPro Path & Area Light
APL-3030-4-B-BZ
Reinstall Lens
Place the lens back onto the
bottom of the hat and use the
previously removed screws
to secure. Tighten with a
screwdriver.
Lens
Hat
Screw
7
Install Stake
Determine the desired location
for mounting the stake. Hammer
the stake into the ground until
ange of stake is ush to the
ground. To avoid damage to the
stake, place a board on top of
the stake while hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake

–6––6–
[email protected] • 813.978.3900
–7–
8
Install Fixture to Stake
Pass supply wires through
the open slot of the stake
and thread the xture onto
the stake. Hand tighten until
snug. Clear away area in
ground and lay the supply
wires into wireway slot.
Ground
Stem
Supply Wires
Soil
Stake
9
Wire Connections
Strip both leads from xture wires. Using two UL listed wire connec-
tors (sold separately), connect the leads from xture wires to main
supply cable leads.
Main Supply
Cable
Fixture Wires
Wire Connectors
Install/Replace Lamp
Reverse Step 2 - Step 3 to replace the ame lamp. Then reinstall the bottom
of the hat to protect the lamp. Reverse Step 5 - Step 6 to replace the SCB
lamp. Reinstall the lens to protect the lamp.
IMPORTANT: Flame lamp and SCB lamp must be protected from moisture and
dust at all times. Always reinstall the hat and lens when removed.

IS-APL-3030-4-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2021, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com