AMP Lighting EquaPro Flood Light Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP®EquaPro Flood Light
AAL-1014-4-B-BZ

AMP®EquaPro Flood Light
AAL-1014-4-B-BZ
Important Safety Instructions: Read Before Installation
INSTALLATION & MAINTENANCE GUIDE
!
www.amplighting.com
–2–
[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
Install Stake
1
Board
Stake
Ground Soil
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that are suitable
for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.amplighting.com or call 1-813-978-3900.
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may dam-
age lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
A. (1) Fixture Body
B. (1) Stake
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake
is ush to grade. To avoid
damage to the stake, place a
board on top of the stake while
hammering.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
4.25”
4”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
Install Lamp
3
Remove Lens
2
[email protected] • 813.978.3900
–5–
Install Lens
4
AMP®EquaPro Flood Light
AAL-1014-4-B-BZ
Install Luminaire to Stake
5
Loosen the lens and remove it
from the luminaire.
Luminaire
Lens
Insert the lamp with the correct
wattage and type marked on the
luminaire label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch lamp with bare
hands. Use soft cloth to handle lamp.
NOTE: “Wafer” bi-pin LED lamp also can
be used for this luminaire.
Lamp
“Wafer” Bi-pin
LED Lamp
Socket
Lens Thread the lens back onto
the luminaire and hand
tighten until snug.
Luminaire
Clear away an area in the ground at
the wireway slot on top of the stake.
Align the wireway slot on the base of
the stake. Lay the luminaire pigtail
into the wireway slot and screw the
luminaire onto the stake. Tighten
until snug to secure the base.
Luminaire
Stake
Pigtail
Wireway Slot
Wire Connection
6
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold seperatley), connect the leads from the luminaire to the main low
voltage supply cable leads.
Pigtail
Main Low Voltage
Supply Cable
Wire Connectors

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
[email protected] • 813.978.3900
–7–
AMP®EquaPro Flood Light
AAL-1014-4-B-BZ
Install/Replace Bi-Pin
7
Remove the lens to expose the Bi-Pin and replace it
with the correct wattage and type marked on the xture label. Then,
reinstall the lens.
IMPORTANT: Bi-Pin must be protected from moisture and dust at all
times. Always reinstall the lens when removed.

IS-AAL-1014-4-B-BZ.ver2
Specications and product details subject to change without notice.
© Copyright 2019, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com