AMP AWL-5012 Operating and safety instructions

- 1 -
AMP®LOW VOLTAGE LANDSCAPE LIGHTING
AMP® Core Drill Well Light
ITEM: AWL-5012
INSTALLATION & MAINTENANCE GUIDE
1-813-978-3900 • Mon-Fri 9am-6pm (EST)

IMPORTANT SAFETY INSTRUCTIONS: READ BEFORE INSTALLATION
INSTALLATION & MAINTENANCE GUIDE
!
This fixture is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes
and instructions may result in serious injury, property damage and
void the warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or
servicing this fixture.
2. Warning: this fixture is not intended to be installed within 10 feet
[3 meters] of a pool, spa or fountain.
3. This fixture is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2
cm) in order to connect to the main low voltage cable.
5. Wiring connections must be made with UL Listed wire connectors
that is suitable for the application.
6. Position the wire connector so that it is located within 6 inches
(15.2 cm) from a building structure, a luminaire, or fitting.
IMPORTANT SAFETY INSTRUCTIONS
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
LIGHTED LAMP IS HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
AMP® Core Drill Well Light - AWL-5012
813.978.3900 • [email protected]om • www.amplighting.com
2

PACKAGE CONTENTS
PARTS REQUIRED (SOLD SEPARATELY)
A. (1) Fixture Body
B. (1) PVC tube
813.978.3900 • [email protected]om • www.amplighting.com
2
813.978.3900 • [email protected]om • www.amplighting.com
3
PRODUCT DIMENSIONS
A. (1) MR11 Lamp
2.17”
1.85”
5.19”
5.87”

REMOVE GLARE GUARD
1
ADJUST SOCKET HEIGHT
2
INSTALLATION & MAINTENANCE GUIDE
AMP® Core Drill Well Light - AWL-5012
813.978.3900 • [email protected]om • www.amplighting.com
4
Unscrew the glare guard to
remove it from the fixture
body.
Fixture
Body
Glare Guard
To get more or less glare
protection, push the socket
to adjust higher or lower
inside of the fixture body.
PUSH
Socket
Fixture
Body
INSTALL LAMP
3
Insert MR11 lamp with correct
wattage and type marked
on the fixture label and push
firmly into place.
CAUTION: Do not exceed
maximum wattage marked on
fixture label.
Socket
MR11 Lamp

INSTALL GLARE GUARD
4
DIG HOLE
5
813.978.3900 • [email protected]om • www.amplighting.com
4
813.978.3900 • [email protected]om • www.amplighting.com
5
Thread the glare guard back
onto the fixture body and
hand tighten until snug.
Glare Guard
Fixture
Body
3”
3”
3”
Dig hole in the ground.
Make sure there is
approximately 3” of space
surrounding the PVC tube
for pea gravel or sand.
PVC Tube
Ground
Soil
Hole

WIRE CONNECTION
6
INSTALLATION & MAINTENANCE GUIDE
AMP® Core Drill Well Light - AWL-5012
813.978.3900 • [email protected]om • www.amplighting.com
6
Pass fixture supply cable
through the PVC tube.
Place the fixture body onto
the PVC tube properly.
Strip both leads from
the fixture supply cable
and the main supply
cable. Using two UL listed
wire connectors (sold
separately), connect the
leads from the fixture
supply cable to the main
supply cable.
Fixture
Body
PVC Tube
Soil
Wire
Connector
Fixture Supply Cable
Main Supply Cable

Reverse steps 3 - 4 to remove the glare guard to expose the MR11 lamp
and replace it with the correct wattage and type marked on the fixture
label. Then, reinstall the glare guard.
IMPORTANT: MR11 Lamp must be protected from moisture and dust at
all times. Always re-install the glare guard when removed.
INSTALL/REPLACE LAMP
813.978.3900 • [email protected]om • www.amplighting.com 813.978.3900 • [email protected]om • www.amplighting.com
7
FILL PEA GRAVEL OR SAND
7
Install the PVC tube with
fixture in hole and fill hole
with pea gravel or sand.
Pea Gravel PVC Tube with Fixture

Specifications and product details subject to change without notice.
© Copyright 2023, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected]om • amplighting.com
1-813-978-3900 • Mon-Fri 9am-6pm (EST)