AMP MagnumPro ASM-2407 Operating and safety instructions

- 1 -
INSTALLATION & MAINTENANCE GUIDE
AMP®LOW VOLTAGE LANDSCAPE LIGHTING
AMP® MagnumPro™ Copper Path & Area Light (Lamp-Ready)
ITEM: ASM-2407/1203
1-813-978-3900 • Mon-Fri 9am-6pm (EST)

IMPORTANT SAFETY INSTRUCTIONS: READ BEFORE INSTALLATION
INSTALLATION & MAINTENANCE GUIDE
!
IMPORTANT SAFETY INSTRUCTIONS
!
AMP® MagnumPro™ Copper Path & Area Light (Lamp-Ready) - ASM-2407/1203
813.978.3900 • [email protected]om • www.amplighting.com
2
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that
are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire, or fitting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.amplighting.com or call 1-813-978-3900.
LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the fixture with a damaged or missing lens or
shield.

PACKAGE CONTENTS
A. Stem
813.978.3900 • [email protected]om • www.amplighting.com
2
813.978.3900 • [email protected]om • www.amplighting.com
3
Parts Required (sold separately)
A. (1) Hat
B. (1) Bulb
C. Stake
Product Dimensions
Magnum Hat Pictured Here on
Standard stem Magnum Hat Pictured Here on
Mini stem
9”
2 1/2”
22 1/2”

1
Stem
Bulb
Stem Top
2
813.978.3900 • [email protected]om • www.amplighting.com
4
Remove Stem Top
Loosen the stem top and
remove it from the stem.
Install Bulb
Insert the bulb with the correct
wattage and type marked on the
fixture label and push firmly into
place.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
Stem
3
Install Stem Top
Place the stem top over the
bulb and thread the stem
top onto the stem. Hand
tighten until snug.
Stem Top
INSTALLATION & MAINTENANCE GUIDE
AMP® MagnumPro™ Copper Path & Area Light (Lamp-Ready) - ASM-2407/1203

4
5
813.978.3900 • [email protected]om • www.amplighting.com
4
813.978.3900 • [email protected]om • www.amplighting.com
5
Install Stake
Determine the desired location
for mounting the fixture. Hammer
the stake into the ground until
the flange of the stake is flush to
grade. To avoid damage to the
stake, place a board on top of the
stake while hammering.
NOTE: If the ground is hard and
the stake is difficult to install,
make a crosscut in the ground
using a flat shovel.
Board
Stake
Soil
Ground
Install Stem to Stake
Clear away an area in the
ground at the wireway slot
on the top of the stake. Lay
the luminaire pigtail into the
wireway slot and attach the
stem onto the stake. Tighten
until snug.
Stem
Wireway Slot
Pigtail
Stake

6
7
813.978.3900 • [email protected]om • www.amplighting.com
6
Wire Connection
Strip both leads from the luminaire pigtail. Using two wire
connectors (sold separately), connect the leads from the
luminaire to the main supply cable leads.
Wire Connections
Pigtail
Main Supply Cable
Install Cast Brass Hat to Stem (Option A)
Thread the hat of your choice
onto the stem top. Hand
tighten until snug.
Note: For Cast Brass AMP®
hats you will not need a finial
to install the hat. You will
screw the hat directly to the
top of the stem.
Hat of Choice
Stem Top
INSTALLATION & MAINTENANCE GUIDE
AMP® MagnumPro™ Copper Path & Area Light (Lamp-Ready) - ASM-2407/1203

INSTALLREPLACE LAMP
813.978.3900 • [email protected]om • www.amplighting.com 813.978.3900 • [email protected]om • www.amplighting.com
7
8
Install Spun Brass Hat to Stem (Option B)
Place the hat of your choice
onto the stem top and secure
it with the finial. Hand tighten
until snug.
Hat of Choice
Finial
Stem Top
Remove the hat and stem top to expose the bulb. Replace it
with the correct wattage and type marked on the fixture label.
Then, reinstall the stem top and hat.
IMPORTANT: Bulbs must be protected from moisture and dust at
all times. Always reinstall the stem top and hat when removed.

Specifications and product details subject to change without notice.
© Copyright 2023, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected]om • amplighting.com
1-813-978-3700 • Mon-Fri 9am-6pm (EST)