AMP EquaPro Brass Black Flood Light Operating and safety instructions

- 1 -
INSTALLATION & MAINTENANCE GUIDE
AMP®LOW VOLTAGE LANDSCAPE LIGHTING
AMP® EquaPro Brass Black Flood Light
ITEM: AAL-1014-4-B-BK
1-813-978-3900 • Mon-Fri 9am-6pm (EST)

IMPORTANT SAFETY INSTRUCTIONS: READ BEFORE INSTALLATION
INSTALLATION & MAINTENANCE GUIDE
!
IMPORTANT SAFETY INSTRUCTIONS
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
LIGHTED LAMP IS HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
AMP®- EquaPro Brass Black Flood Light - AAL-1014-4-B-BK
813.978.3900 • [email protected]om • www.amplighting.com
2
This luminaire is intended for installation in accordance with local codes and the
National Electric Code (NEC). Failure to adhere to these codes and instructions may
result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more
from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (transformer)
rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that are suitable for
outdoor use.
5. Position the low voltage wire and wire connector so that it is located within 6
inches (15.2 cm) from a building structure, a luminaire or fitting.
6. The main low voltage cable is intended for shallow burial - less than 6 inches
(152 mm).
7. If additional lengths of low voltage cable are required, please contact www.
amplighting.com or call 1-813-978-3900.

PACKAGE CONTENTS
PRODUCT DIMENSIONS
A. (1) Fixture Body
INSTALL STAKE
1
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until flange of stake
is flush to grade. To avoid
damage to the stake, place a
board on top of the stake while
hammering.
Note: If the ground is hard and
the stake is difficult to install,
make a crosscut in the ground
using a flat shovel.
Board
Ground
Soil
Stake
813.978.3900 • [email protected]om • www.amplighting.com
2
813.978.3900 • [email protected]om • www.amplighting.com
3
4.25”
4”

REMOVE LENS
2
INSTALL LAMP
3
813.978.3900 • [email protected]om • www.amplighting.com
4
Loosen the lens and remove it
from the luminaire.
Lens
Fixture
Insert the lamp with the correct
wattage and type marked on the
luminaire label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch lamp with bare
hands. Use soft cloth to handle lamp.
NOTE: “Wafer” bi-pin LED lamp also
can be used for this luminaire.
“Wafer” Bi-Pin LED
Lamp
Socket
Lamp
INSTALLATION & MAINTENANCE GUIDE
AMP®- EquaPro Brass Black Flood Light - AAL-1014-4-B-BK

INSTALL LENS
4
INSTALL FIXTURE TO STAKE
5
813.978.3900 • [email protected]om • www.amplighting.com
4
813.978.3900 • [email protected]om • www.amplighting.com
5
Thread the lens back onto the
luminaire and hand tighten
until snug.
Lens
Fixture
Clear away an area in the ground
at the wireway slot on top of the
stake. Align the wireway slot on
the base of the stake. Lay the
luminaire pigtail into the wireway
slot and screw the luminaire onto
the stake. Tighten until snug to
secure the base.
Fixture
Stake
Wireway Slot
Pigtail
WIRE CONNECTION
6
Strip both leads from the luminaire pigtail. Using two wire
connectors (sold separately), connect the leads from the luminaire
to the main low voltage supply cable leads.
Pigtail
Main Low Voltage
Cable
Wire Connectors

813.978.3900 • [email protected]om • www.amplighting.com
6
Remove the lens to expose the Bi-Pin and replace it
with the correct wattage and type marked on the fixture label. Then,
reinstall the lens.
IMPORTANT: Bi-Pin must be protected from moisture and dust at all
times. Always reinstall the lens when removed.
INSTALL/REPLACE LAMP
INSTALLATION & MAINTENANCE GUIDE
AMP®- EquaPro Brass Black Flood Light - AAL-1014-4-B-BK

813.978.3900 • [email protected]om • www.amplighting.com 813.978.3900 • [email protected]om • www.amplighting.com
7

1-813-978-3900 • Mon-Fri 9am-6pm (EST)
Specifications and product details subject to change without notice.
© Copyright 2023, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected]om • amplighting.com