AMP HydraPro AWL-5006 Operating and safety instructions

- 1 -
AMP®LOW VOLTAGE LANDSCAPE LIGHTING
AMP® HydraProTM Black In-Grade Light (Lamp-Ready)
ITEM: AWL-5006
INSTALLATION & MAINTENANCE GUIDE
1-813-978-3900 • Mon-Fri 9am-6pm (EST)

IMPORTANT SAFETY INSTRUCTIONS: READ BEFORE INSTALLATION
INSTALLATION & MAINTENANCE GUIDE
!
This fixture is intended for installation in accordance with local codes and the
National Electric Code (NEC). Failure to adhere to these codes and instructions
may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
fixture.
2. Warning: this fixture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This fixture is intended to be used only with a power supply (transformer)
rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with UL listed wire connectors that are
suitable for the application.
6. Position the wire connector so that it is located within 6 inches (15.2 cm)
from a building structure, a luminaire, or fitting.
IMPORTANT SAFETY INSTRUCTIONS
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
LIGHTED LAMP IS HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
AMP® HydraProTM MR11 Black In-Grade Light (Lamp Ready) - AWL-5006
813.978.3900 • [email protected]om • www.amplighting.com
2

PACKAGE CONTENTS
PARTS REQUIRED (SOLD SEPARATELY)
813.978.3900 • [email protected]om • www.amplighting.com
2
813.978.3900 • [email protected]om • www.amplighting.com
3
A. (1) Fixture Body
A. (1) MR11 Lamp
PRODUCT DIMENSIONS
2.75”
2.85”

REMOVE FACEPLATE
1
INSTALL LAMP
2
INSTALLATION & MAINTENANCE GUIDE
AMP® HydraProTM MR11 Black In-Grade Light (Lamp Ready) - AWL-5006
813.978.3900 • [email protected]om • www.amplighting.com
4
Use a screwdriver to loosen
the screws on the faceplate
and remove the lens from the
fixture body.
Screw
Faceplate
Lens
Fixture Body
Insert the lamp with the correct
wattage and type marked on the
fixture label and push firmly into
place.
CAUTION: Do not exceed
maximum wattage marked on
fixture label.
MR11 Lamp
Socket
INSTALL FACEPLATE
3
Place the lens and the
faceplate back onto the fixture
body and secure the removed
screws in a star pattern using a
screwdriver. Tighten until snug.
Screw
Faceplate
Lens
Fixture Body

REMOVE THE LENS
4
WIRE CONNECTION
5
813.978.3900 • [email protected]om • www.amplighting.com
4
813.978.3900 • [email protected]om • www.amplighting.com
5
3”
3”
3”
Prepare a hole in the
ground. Make sure there
are approximately 3” spaces
surrounding the fixture for
pea gravel or sand.
Hole
Soil
Strip both leads from the luminaire pigtail. Using two wire
connectors (sold separately), connect the leads from the fixture
body to the main supply cable leads.
Supply Cable Wire Connectors
Main Supply Cable
Pigtail

FILL HOLE
6
REMOVE FACEPLATE
7
INSTALL/REPLACE GLARE GUARD
INSTALLATION & MAINTENANCE GUIDE
AMP® HydraProTM MR11 Black In-Grade Light (Lamp Ready) - AWL-5006
813.978.3900 • [email protected]om • www.amplighting.com
6
Install the fixture in the
hole and fill the hole with
pea gravel or sand.
Pea Gravel or Sand Fixture
Soil
Use a screwdriver to loosen
the screws on the faceplate
and remove the lens from the
fixture body.
Screw
Faceplate
Lens
Fixture Body

813.978.3900 • [email protected]om • www.amplighting.com 813.978.3900 • [email protected]om • www.amplighting.com
7
REPLACE FACEPLATE
8
Place the lens and faceplate
onto the fixture body and
secure with previously
removed screws in a star
pattern. Hand tighten until
snug with a screwdriver.
Faceplate Replacement Options
Screw
Faceplate
Lens
Fixture Body
INSTALL/REPLACE LAMP
Repeat step 1 - step 3 to remove the faceplate and expose the
lamp. Replace it with the correct wattage and type marked on the
fixture label. Then, reinstall the faceplate.
IMPORTANT: Lamps must be protected from moisture and dust at
all times. Always reinstall the faceplate when removed.

Specifications and product details subject to change without notice.
© Copyright 2023, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected]om • amplighting.com
1-813-978-3900 • Mon-Fri 9am-6pm (EST)