AMP StoutPro PAR36 G2 Brass Black Flood Light Operating and safety instructions

- 1 -
INSTALLATION & MAINTENANCE GUIDE
AMP®LOW VOLTAGE LANDSCAPE LIGHTING
AMP® StoutPro PAR36 G2 Brass Black Flood Light
(Lamp Ready)
ITEM: AFL-4015
1-813-978-3900 • Mon-Fri 9am-6pm (EST)

IMPORTANT SAFETY INSTRUCTIONS: READ BEFORE INSTALLATION
!
IMPORTANT SAFETY INSTRUCTIONS
!
INSTALLATION & MAINTENANCE GUIDE
AMP® StoutPro PAR36 G2 Brass Black Flood Light
(Lamp Ready)
813.978.3900 • [email protected]om • www.amplighting.com
2
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that
are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO
PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning
on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire fitting with a missing or damaged
shield.
SAVE THESE INSTRUCTIONS

PACKAGE CONTENTS
1
813.978.3900 • [email protected]om • www.amplighting.com
2
813.978.3900 • [email protected]om • www.amplighting.com
3
A. (1) Fixture
PRODUCT DIMENSIONS
Parts Required (sold separately)
A. (1) PAR36 Bulb
B. (1) Mounting Accessory
2.3”
4.65”
4.25”
Remove Glare Guard
Rotate the glare guard
counter clockwise and
remove it from the fixture.
Then remove the bulb
holder.
ROTATE
Bulb Holder
Glare Guard
Fixture

2
3
INSTALLATION & MAINTENANCE GUIDE
AMP® StoutPro PAR36 G2 Brass Black Flood
Light (Lamp-Ready)
813.978.3900 • [email protected]om • www.amplighting.com
4
Install PAR36 Bulb
Use a PAR36 bulb (sold
separately), with the correct
wattage and type as marked
on luminaire label. Connect
the supply wires using the
screws on the bottom of the
PAR36 bulb, tighten with a
screwdriver.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
NOTE: DO NOT touch lamp
with bare hands. Use soft cloth
to handle lamp.
Supply Wire
Par36 Bub
Screw
Fixture
Install Bulb Holder and Glare Guard
Tuck the excess wires
inside of the fixture and
place the PAR36 bulb
inside. Place the bulb
holder onto the top of the
PAR36 bulb and thread
the glare guard onto the
fixture.
PAR36 Bulb
Fixture Bulb Holder
Glare Guard

4
5
813.978.3900 • [email protected]om • www.amplighting.com
4
813.978.3900 • [email protected]om • www.amplighting.com
5
Determine the desired
location for mounting the
stake. Hammer the stake
into the ground until flange
of stake is flush to grade. To
avoid damage to the stake,
place a board on top of the
stake while hammering.
Note: If the ground is hard
and the stake is difficult to
install, make a crosscut in the
ground using a flat shovel.
Install Stake
Board
Ground
Stake
Soil
Install Fixture to Stake
Clear away an area in the
ground at the wireway slot
on the top of the stake. Place
the fixture wire into the
wireway slot and thread the
fixture onto the stake. Hand
tighten until snug.
Fixture
Ground
Stake
Cable
Soil
 

6
ADJUST LUMINAIRE DIRECTION
7
INSTALLATION & MAINTENANCE GUIDE
AMP® StoutPro PAR36 G2 Brass Black Flood
Light (Lamp-Ready)
813.978.3900 • [email protected]om • www.amplighting.com
6
Wire Connections
Strip both leads from the xture pigtail. Using two UL listed wire
connectors (sold separately), connect the leads from the xture to the
main supply cable leads.
Wire Connections
Pigtail
Main Supply Cable
ROTATE
Loosen the knuckle and adjust
the fixture to the desired
orientation. Tighten the knuckle
after you find the desired
orientation.
Fixture
Screw

INSTALLREPLACE LAMP
813.978.3900 • [email protected]om • www.amplighting.com 813.978.3900 • [email protected]om • www.amplighting.com
7
Reverse Step 1 - Step 3 to expose the PAR36 bulb and replace it with
correct
wattage and type marked on luminaire label. Reinstall glare guard.
IMPORTANT: Halogen lamps must be protected from moisture and
dust at all times. Always reinstall glare guard when removed.

Specifications and product details subject to change without notice.
© Copyright 2023, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected]om • amplighting.com
1-813-978-3700 • Mon-Fri 9am-6pm (EST)