AMP Mini PinnaclePro MR11 Operating and safety instructions

INSTALLATION & MAINTENANCE
GUIDE
AMP®LOW VOLTAGE LANDSCAPE LIGHTING
AMP® Mini PinnaclePro Black Spotlight
ITEM: AAL-1018-4-B-BK
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
- 1 -

IMPORTANT SAFETY INSTRUCTIONS: READ BEFORE INSTALLATION
INSTALLATION & MAINTENANCE GUIDE
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that are suitable
for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.amplighting.com or call 1-813-978-3900.
IMPORTANT SAFETY INSTRUCTIONS
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
LIGHTED LAMP IS HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire fitting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
AMP® Mini PinnaclePro Black Spotlight -AAL-1018-4-B-BK
813.978.3900 • [email protected]om • www.amplighting.com
2

PACKAGE CONTENTS
PRODUCT DIMENSIONS
REMOVE GLARE GUARD AND SHIELD FROM FIXTURE
1
813.978.3900 • [email protected]om • www.amplighting.com
2
813.978.3900 • [email protected]om • www.amplighting.com
3
A. (1) Fixture
B. (1) Stake
2.75”
4.5”
2.75”
1.75”
Loosen the set screw and remove
the glare guard from the shield.
Loosen the shield and remove it
from the fixture.
Glare Guard
Shield
Set Screw
Fixture

INSTALL MR11 LAMP
2
INSTALL GLARE GUARD AND SHIELD TO FIXTURE
3
813.978.3900 • [email protected]om • www.amplighting.com
4
Insert the lamp with the correct
wattage and type marked on the
fixture label.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
NOTE: DO NOT touch lamp with
bare hands. Use soft cloth to
handle lamp.
Socket
MR11 Lamp
Attach the shield back onto the
fixture. Place the glare guard over
the shield and secure with the set
screw. Tighten until snug.
Fixture
Set Screw
Shield
Glare Guard
INSTALLATION & MAINTENANCE GUIDE
AMP® Mini PinnaclePro Black Spotlight -AAL-1018-4-B-BK

INSTALL STAKE
4
INSTALL FIXTURE TO STAKE
5
813.978.3900 • [email protected]om • www.amplighting.com
4
813.978.3900 • [email protected]om • www.amplighting.com
5
Determine the desired location for
mounting the fixture. Hammer the
stake into the ground until flange
of stake is flush to grade. To avoid
damage to the stake, place a board on
top of the stake while hammering.
NOTE: If the ground is hard and the
stake is difficult to install, make a
crosscut in the ground using a flat
shovel.
Board
Soil
Stake
Ground
Clear away an area in the ground
at the wireway slot on top of the
stake. Lay the luminaire pigtail
into the wireway slot and screw
the fixture onto the stake. Tighten
until snug.
Wireway Slot
Fixture
Pigtail
Stake

WIRE CONNECTIONS
6
813.978.3900 • [email protected]om • www.amplighting.com
6
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the luminaire to the main
supply cable leads.
Pigtail
Main Supply Cable
Wire Connectors
INSTALLATION & MAINTENANCE GUIDE
AMP® Mini PinnaclePro Black Spotlight -AAL-1018-4-B-BK

Remove the glare guard and the lens to expose the MR11 lamp and replace it
with the correct wattage and type marked on the fixture label. Then,
reinstall the lens and the glare guard.
IMPORTANT: MR11 lamp must be protected from moisture and dust at all
times. Always reinstall the lens and the glare guard when removed.
INSTALL/REPLACE LAMP
813.978.3900 • [email protected]om • www.amplighting.com 813.978.3900 • [email protected]om • www.amplighting.com
7

Specifications and product details subject to change without notice.
© Copyright 2023, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected]om • amplighting.com
1-813-978-3900 • Mon-Fri 9am-6pm (EST)