AmTryke 50-FC-1516 User manual


www.missioncycles.co.uk
Amtryke
Model50‐FC‐1516&50‐FC‐1520
AssemblyInstructions





ToolsRequiredforAssembly
6mmand5mmAllenwrench(included)
10mmwrenchorsocket
14mmwrenchorsocket
15mmwrenchorsocket
22mmwrenchorsocket
#2Phillipsheadscrewdriver


Page1of20
Unit3TheAlders,SevenMileLane,Mereworth,KentME185JG
Email:[email protected]Tel01622815678

1)Slidethefrontframesectionintotherearframesection.



2)Sliderearwheelsontoaxleoneachside.



Page2of20
Unit3TheAlders,SevenMileLane,Mereworth,KentME185JG
Email:[email protected]Tel01622815678


3)Installrearaxlenutontoleftandrightsideofthreadedaxle.Usea22mmsocket
orwrenchtotighten.



4)Installwhiteaxlenutcoverontoaxlenut,pressfirmlyandthenlightlytapwith
hammer.




Page3of20
Unit3TheAlders,SevenMileLane,Mereworth,KentME185JG
Email:[email protected]Tel01622815678

5)Loosennutsonfromwheelaxleandtheninstallfromwheelontofork,usea
15mmwrenchorsockettotightennuts.



6)Insertframesafetypinthroughbothsectionsoftheframefully.



Page4of20
Unit3TheAlders,SevenMileLane,Mereworth,KentME185JG
Email:[email protected]Tel01622815678

7)Installframeknobbyturninginclockwise,dotothenewframedesignyouwill
onlybeabletoturn½aturnatatime.



8)Installloadingbrakebyplacebrakeassemblyontopofframeandinstallingthe
twoAllenboltsfromthebottom.




Page5of20
Unit3TheAlders,SevenMileLane,Mereworth,KentME185JG
Email:[email protected]Tel01622815678

9)Installthehandlebarstembyplacingitintheheadtube,markedonthesideof
thestemisthemaximumheightline;pleasepaycloseattentiontothis.



10)Removetwo6mmAllenboltsfromsteeringstemhandlebarclamp,insert
handlebarandreplacehandlebarclampandtightentwo6mmAllenscrews.





Page6of20
Unit3TheAlders,SevenMileLane,Mereworth,KentME185JG
Email:[email protected]Tel01622815678

11)Installseatpostontorearframesection,removetwoleversbyunscrewing
(counterclockwise).Placeredseatpostonframeandplaceclampingplateon
bottomofframewithtwoleversgoingthroughplateandscrew(clockwise)into
matingpiece.





Page7of20
Unit3TheAlders,SevenMileLane,Mereworth,KentME185JG
Email:[email protected]Tel01622815678


12)Installthepedallevellerpulleybyturningitclockwiseintothefrontholeonthe
blackplate.



13)Locatedattherearofthe1516or1520aretwo6mmAllenbolts,removeboth
Allenbolts.



Page8of20
Unit3TheAlders,SevenMileLane,Mereworth,KentME185JG
Email:[email protected]Tel01622815678


14)Placethewhitebasketontheblackplateandaligntheholesinthebasketwith
theholesintheblackplate



15)Placemetalbasketbraceinbasketsothatitalignsupwiththetwoholesthat
youremovedthe6mmAllenboltsfrom.


Page9of20
Unit3TheAlders,SevenMileLane,Mereworth,KentME185JG
Email:[email protected]Tel01622815678



16)Installtwo6mmAllenboltsthatyouremovedearlierthroughthemetalbasket
braceandintotherearframeofthe1516or1520turnclockwisetotighten.




17)Removetheblackknoblocatedontheleftsideofthefork.




Page10of20
Unit3TheAlders,SevenMileLane,Mereworth,KentME185JG
Email:[email protected]Tel01622815678