Analog Devices ADSP-BF609 EZ-KIT Lite User manual

a
ADSP-BF609 EZ-KIT Lite®
Evaluation System Manual
Revision 1.1, May 2014
Part Number
82-000269-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106

Copyright Information
©2014 Analog Devices, Inc., ALL RIGHTS RESERVED. This document
may not be reproduced in any form without prior, express written consent
from Analog Devices, Inc.
Printed in the USA.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by impli-
cation or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, Blackfin, CrossCore, EngineerZone, EZ-Board,
EZ-Extender, EZ-KIT Lite, and VisualDSP++ are registered trademarks of
Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.

Regulatory Compliance
The ADSP-BF609 EZ-KIT Lite is designed to be used solely in a labora-
tory environment. The board is not intended for use as a consumer end
product or as a portion of a consumer end product. The board is an open
system design which does not include a shielded enclosure and therefore
may cause interference to other electrical devices in close proximity. This
board should not be used in or near any medical equipment or RF devices.
The ADSP-BF609 EZ-KIT Lite has been certified to comply with the
essential requirements of the European EMC directive 2004/108/EC and
therefore carries the “CE” mark.
The ADSP-BF609 EZ-KIT Lite has been appended to Analog Devices,
Inc EMC Technical File (EMC TF) referenced DSPTOOLS1, issue 2
dated June 4, 2008 and was declared CE compliant by an appointed Noti-
fied Body (No.0673) as listed below.
Notified Body Statement of Compliance: Z600ANA2.043 dated August
24, 2012.
Issued by: Technology International (Europe) Limited
56 Shrivenham Hundred Business Park
Shrivenham, Swindon, SN6 8TY, UK
The EZ-KIT Lite evaluation system contains ESD (electrostatic discharge)
sensitive devices. Electrostatic charges readily accumulate on the human
body and equipment and can discharge without detection. Permanent dam-
age may occur on devices subjected to high-energy discharges. Proper ESD
precautions are recommended to avoid performance degradation or loss of
functionality. Store unused EZ-KIT Lite boards in the protective shipping
package.

ADSP-BF609 EZ-KIT Lite Evaluation System Manual v
CONTENTS
PREFACE
Product Overview ............................................................................ x
Purpose of This Manual ................................................................ xiii
Intended Audience ........................................................................ xiii
Manual Contents ........................................................................... xiv
What’s New in This Manual ........................................................... xiv
Technical Support ........................................................................... xv
Supported Processors ...................................................................... xvi
Product Information ...................................................................... xvi
Analog Devices Web Site .......................................................... xvi
EngineerZone .......................................................................... xvii
Related Documents ...................................................................... xviii
Notation Conventions .................................................................. xviii

Contents
vi ADSP-BF609 EZ-KIT Lite Evaluation System Manual
USING ADSP-BF609 EZ-KIT LITE
Package Contents ......................................................................... 1-2
ADSP-BF609 EZ-Board ............................................................... 1-3
Default Configuration .................................................................. 1-3
Supported Operating Systems ...................................................... 1-5
System Requirements .................................................................... 1-5
EZ-KIT Lite Installation ............................................................... 1-6
EZ-KIT Lite Session Startup ......................................................... 1-7
Evaluation License ...................................................................... 1-10
Memory Map ............................................................................. 1-10
DDR2 SDRAM .......................................................................... 1-12
SPI Interface .............................................................................. 1-13
SMC Interface ............................................................................ 1-13
Ethernet Interface ....................................................................... 1-13
USB OTG HS Interface .............................................................. 1-14
CAN Interface ............................................................................ 1-15
UART Interface .......................................................................... 1-15
SD Interface ............................................................................... 1-16
Rotary Encoder Interface ............................................................ 1-16
Temperature Sensor Interface ...................................................... 1-17
Link Ports Interface .................................................................... 1-18
General-Purpose I/O (GPIO) ...................................................... 1-18
JTAG Interface ........................................................................... 1-19
Power-On-Self Test ..................................................................... 1-20

ADSP-BF609 EZ-KIT Lite Evaluation System Manual vii
Contents
Expansion Interface III ................................................................ 1-20
Power Architecture ...................................................................... 1-21
Power Measurements ................................................................... 1-21
Example Programs ...................................................................... 1-22
Reference Design Information ..................................................... 1-22
ADSP-BF609 EZ-KIT LITE HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
Software-Controlled Switches (SoftConfig) .................................... 2-3
Overview of SoftConfig ........................................................... 2-3
SoftConfig on the ADSP-BF609 EZ-KIT LITE ...................... 2-7
Programming SoftConfig Switches ........................................... 2-8
Push Buttons and Switches .......................................................... 2-18
JTAG Interface Switches (SW1, SW3–5) ................................ 2-18
Boot Mode Select Switch (SW2) ............................................ 2-20
IRQ/Flag Enable Switches (SW6–7) ....................................... 2-21
Reset Switch (SW8) ............................................................... 2-21
Rotary Encoder With Momentary Switch (SW9) .................... 2-21
Wake Push Switch (SW10) .................................................... 2-22
Power Jumpers ............................................................................ 2-22

Contents
viii ADSP-BF609 EZ-KIT Lite Evaluation System Manual
LEDs ......................................................................................... 2-23
GPIO LEDs (LED1–4) ......................................................... 2-24
Thermal Limit LED (LED5) ................................................. 2-24
Power LED (LED6) .............................................................. 2-24
Reset LED (LED7) ............................................................... 2-25
SPD LED (LED6) ................................................................ 2-25
Connectors ................................................................................. 2-25
DCE UART Connector (J2) .................................................. 2-26
Link Port /JTAG Connectors (J3 and P8) .............................. 2-26
JTAG Connector (P1) ........................................................... 2-26
JTAG Connector (ZP1) ......................................................... 2-27
Expansion Interface III Connectors (P1A–C, P2A, P3A) ........ 2-27
USB Connector (P7) ............................................................. 2-27
Power Connector (P18) ......................................................... 2-27
CAN Connector (J4) ............................................................ 2-28
SD Connector (J5) ................................................................ 2-28
Ethernet Connector (J1) ....................................................... 2-28
Ethernet Connectors (P16-17) ............................................... 2-28
ADSP-BF609 EZ-KIT LITE BILL OF MATERIALS
ADSP-BF609 EZ-KIT LITE SCHEMATIC
INDEX

ADSP-BF609 EZ-KIT Lite Evaluation System Manual ix
PREFACE
Thank you for purchasing the ADSP-BF609 EZ-KIT Lite®, Analog
Devices, Inc. low-cost evaluation system for the ADSP-BF60x Blackfin®
processors.
The ADSP-BF609 processor is a member of the Blackfin family of prod-
ucts, incorporating the Analog Devices/Intel Micro Signal Architecture
(MSA). Blackfin processors combine a dual-MAC state-of-the-art signal
processing engine, the advantages of a clean, orthogonal RISC-like micro-
processor instruction set, and single-instruction, multiple-data (SIMD)
multimedia capabilities into a single instruction-set architecture.
ADSP-BF60x Blackfin processors embody a new type of embedded pro-
cessor designed specifically to meet the computational demands and
power constraints of today’s automotive systems, embedded industrial,
instrumentation, and power/motor control applications.
The evaluation board is designed to be used in conjunction with the
CrossCore®Embedded Studio (CCES) development tools to test capabil-
ities of the ADSP-BF60x Blackfin processors. The CCES development
environment aids advanced application code development and debug,
such as:
• Create, compile, assemble, and link application programs written
in C++, C, and assembly
• Load, run, step, halt, and set breakpoints in application programs
• Read and write data and program memory

Product Overview
x ADSP-BF609 EZ-KIT Lite Evaluation System Manual
• Read and write core and peripheral registers
• Plot memory
Access to the processor from a personal computer (PC) is achieved
through a USB port (when a debug agent is mounted on the EZ-KIT Lite
board) or an external JTAG emulator. The USB interface provides unre-
stricted access to the ADSP-BF609 processor and evaluation board
peripherals. Analog Devices JTAG emulators offer faster communication
between the host PC and target hardware. Analog Devices carries a wide
range of in-circuit emulation products. To learn more about Analog
Devices emulators and processor development tools, go to:
http://www.analog.com/processors/tools/.
The ADSP-BF609 EZ-KIT Lite provides example programs to demon-
strate the product capabilities.
The ADSP-BF609 EZ-KIT Lite software is part of the EZ-Board®
BSP (Board Support Package) for the Blackfin ADSP-BF60x family
which needs to be installed after CrossCore Embedded Studio. The
EZ-KIT Lite is a licensed product that offers an unrestricted evalu-
ation license for 90 days after activation. For more information,
refer to Evaluation License in this manual and the Installation
Quick Reference Card.
Product Overview
The board features:
• Analog Devices ADSP-BF609 Blackfin processor
• 349-pin LFBGA package
• 25 MHz CLKIN oscillator
• 48 MHz USB CLKIN