Anthro Elevate ELTA136 4 Series User manual

ASSEMBLY INSTRUCTIONS
Anthro Corporation®| 10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: [phone] | email: [email protected] | anthro.com
Outside the U.S. | Tel: [phone] | Fax: [phone]
Elevate,
TM Electric Lift Table
Rev F, January 2013
Product Part#
36"w Single Surface ELTA136zz/xx4
48"w Single Surface ELTA148zz/xx4
60"w Single Surface ELTA160zz/xx4
72"w Single Surface ELTA172zz/xx4

WELCOME
Thank you for purchasing Elevate,™ Electric Lift Table!
If you have any questions or if we can help you in any
way, please contact us at 800.325.3841.
This assembly requires two people.
PARTS LIST
Before beginning assembly of your Table, please
take a moment to review the parts listed below
to verify that your shipment is complete.
A Phillips head screwdriver is required
for this assembly.
2
Product Quantity Part Number
01 Shelf
36"w Elevate 1 100-6577-xx
48"w Elevate 1 100-6578-xx
60"w Elevate 1 100-6579-xx
72"w Elevate 1 100-6580-xx
02 Cross Tube
36"w Elevate 1 125-5277-zz
48"w Elevate 1 125-5184-zz
60"w Elevate 1 125-5185-zz
72"w Elevate 1 125-5186-zz
03 Shelf Gusset (X) 1 225-2269-zz
04 Shelf Gusset (Y) 1 225-2270-zz
Product Quantity Part Number
05 Cableway
36"w Elevate 1 225-2281-zz
48"w Elevate 1 225-2282-zz
60"w Elevate 1 225-2283-zz
72"w Elevate 1 225-2284-zz
06 Leg 2 575-5018-zz
07 Keypad Assembly 1
Keypad 400-5357-00
Keypad Slider 400-5358-00
08 Control Box 1 400-5393-00
09 Basetube 2 500-1005-zz
10 Cross Tube
36"w Elevate 1 500-1007-zz
48"w Elevate 1 500-1008-zz
60"w Elevate 1 500-1009-zz
72"w Elevate 1 500-1010-zz
11 4" Locking Caster 4 150-5065-00
12 Basetube End Cap 4 175-5158-32
13 Wire Management Clip 3 175-5188-00
14 Crosstube End Cap 2 175-5190-32
15 Velcro Tie (not shown) 2 175-5121-03
16 Basetube Washer 4
Black 225-2050-00
Silver Metallic 225-3522-00
17 3/4" Wood Screw 4 325-5106-00
18 3/8" Button Head Cap Screw 4 325-5149-00
19 4" Cap Screw 4 325-5166-00
(CONTINUED NEXT PAGE)
01
03
04
02
05
06
07 08
09
10
11
12
14
22
18
19
20
21
13
16
17

Elevate,TM Electric Lift Table Assembly Instructions 3
PARTS LIST (CONTINUED)
20 20mm Socket Head Cap Screw 16 325-5272-00
21 3/4" Phillips Screw 4 325-5370-00
22 1-1/4" Button Head Screw 16 325-5178-00
Product Quantity Part Number
23 Hex Driver (not shown) 1 375-5000-00
24 1/4" Hex Key (not shown) 1 375-5024-00
25 Rubber Mallet (not shown) 1 375-5022-00
26 5mm Hex Key (not shown) 1 375-5014-00
27 5/32" Hex Driver Bit (not shown) 1 375-5003-00
28 10’ Power Cord (not shown) 1 400-5181-00
Product Quantity Part Number
For 36” and 48” wide Elevates
29 1-meter Control Box Cable (not shown) 2 400-5182-00
For 60” and 72” wide Elevates
30 1-meter Control Box Cable (not shown) 1 400-5182-00
31 2-meter Control Box Cable (not shown) 1 400-5180-00
STEP 1
Attach the Legs to the Base Tubes
¡Hold one leg so the Slot is facing away from you and
the cord is coming out the top. Route the leg cord
through the notch on the top. Using the mallet, firmly
attach the cord grommet to the notch. Make sure that
one leg has the cord on the left and one leg has the
cord on the right.
¡Align a leg with the opening on the base tube so that
the slot on the legs is facing the hole on the base tube
and that the cord comes out the top.
¡Attach with four Socket Head Cap Screws.
¡Repeat for the second leg.
20mm Socket Head Cap Screw
325-5272-00
Leg
Basetube
Slot
Rear
Front
Hole
Cord Grommet
Notch

4Questions? Call us at 800.325.3841 or visit anthro.com. We’re happy to walk you through the assembly!
STEP 4
Attach Cross Tubes to Base Tubes
¡Position the Right Leg Assembly (from Step 2) with
two Cross Tubes as shown. Insert one Cap Screw with a
Curved Washer through a side hole, carefully threading
the Screw into the Cross Tube, but do not tighten all
the way. Repeat for the remaining three side holes.
¡Once all cross tubes are installed, tighten all the
basetube screws. Leave the Wood Screws loose
until Step 6.
STEP 3
Attach Leg Assembly to Shelf
¡Set the top of the cap screws into the recessed
holes in the shelf. Align the holes on the gusset with
pre-drilled holes on the shelf. Attach each leg with
four Wood Screws. Don’t tighten all the way.
1-1/4" Button Head Screw
325-5178-00
4" Cap Screw
325-5166-00
Cross Tube
STEP 2
Attach Gusset to Legs
¡Attaching a gusset to a leg determines an outside and
inside for the leg. The flange on the side of the gusset
goes on the outside of the leg, and the cord goes on
the inside of the leg. Before attaching the gusset,
route the leg cord through the slot on the top of the
leg so the cord goes to the inside of the table. Using
the mallet, firmly attach the cord grommet to the slot.
¡Align a gusset with a leg so that the screw holes on
the gusset match the threaded holes in the leg.
¡Secure a gusset to a leg with four Socket Head Cap
Screws. Repeat for the other leg. 20mm Socket Head Cap Screw
325-5272-00
Shelf Gusset (X) Shelf Gusset (Y)
Rear
Front Front
Basetube Washer
225-2050-00 (Black)
225-3522-00 (Silver)

Elevate,TM Electric Lift Table Assembly Instructions 5
STEP 5
Install Keypad and Control Box
¡Select positions for the Keypad and Control Box,
either the left or right side of the Table. Remember
that the Keypad and Control Box must be on the same
side of the Table. Also, the power cord comes off the
back of the Control Box and should be positioned so
it can reach the outlet.
¡Place the Control Box on the shelf so that the cord
outlets are at the back, then align the Box with the
pre-drilled holes on the shelf. Secure with four Wood
Screws.
¡Align the Keypad and its housing with the four pre-
drilled holes at the front of the keyboard surface so
that the buttons are face-down at the front edge of
the keyboard surface and the flat side of the housing
is against the shelf. Using four Phillips Head Screws,
attach the Keypad and its housing to the front of the
keyboard surface.
¡Route each leg cord from the leg to the control box
and plug them in. Insert cable clips into the table and
route leg cords through them. Plug the keypad cable
into control box. Insert a cable clip into the table and
route the cord through it.
STEP 6
Attach Cable Trough
¡Align the cable trough with the flanges on each leg
gusset and the pre-drilled holes on the shelf. Before
installing the trough, make sure that cables are routed
through the ends of the trough, not into the side of
the trough. Secure the trough to the gussets with four
Button Head Cap Screws. Secure the trough to the
shelf using eight Wood Screws.
STEP 7
Add Casters and Turn Table Right Side Up
¡Thread casters into the caster inserts in each leg. This
is a lot easier if you lock the casters first.
¡With the help of another person, carefully rotate the
Table onto its casters.
¡Plug the power cord into the control box and an
outlet. Insert a cable clip into the base tube closest to
the Control Box and route the power cord through it.
3/4" Wood Screw
325-5106-00
1-1/4" Wood Screw
325-5178-00 3/8" Button Head Cap Screw
325-5149-00
Cable Trough
3/4" Phillips Head Screw
325-5370-00
Keypad Detail
Cable Snap-in Clip
175-51188-00
Cable Snap-in Clip
175-51188-00

6Questions? Call us at 800.325.3841 or visit anthro.com. We’re happy to walk you through the assembly!
STEP 9
Insert End Caps
¡Pop end caps into cross bar and base tubes.
Use the mallet to set them into place.
End Cap
STEP 8
Attach Cross Bar
¡Using the keypad, move shelf all the way up. (Check
the legs for excess lubricant and wipe down if needed.)
¡Align the cross bar so that the tapered ends of the
cross bar brackets line up with the leg brackets. Using
the mallet, drive the cross bar completely into place
(a few whacks on the left, a few on the right, then left,
then right…).
Cross Bar

Elevate,TM Electric Lift Table Assembly Instructions 7
STEP 10
Home the Legs
Legs must be homed any time the table and legs are disconnected from power. If the legs are not homed at both the top and
the bottom, the table will only move at half its normal speed.
¡Press down button until the table reaches its lowest point and stops moving. Release the button for 1-2 seconds. Press
down button again for 3-5 seconds and you will see the table home itself.
¡Press up button until the table tops at the highest point and hold for 3-5 seconds. Press the down button for 2-3
seconds, then the up button again until it tops at the highest point and hold again for 3-5 seconds. (The goal is to have
the table hold at it’s highest point twice.)
¡If the legs ever fail to function properly, unplug the power cord, wait 10 seconds, plug the power cord back in and repeat
the above steps.
STEP 11
Add Accessories and Install Your Equipment
¡Now add your Anthro accessories and install your equipment.
¡A word of caution: the height range of Elevate may be longer than the cords on your equipment. Equipment that is
mounted in a SideRack w/Caster or Equipment Shelf, for example, will not move up and down with the table. Raise and
lower the table to its highest and lowest positions when all equipment is installed to make sure that the cords are long
enough. Double-check that all the table's cords and cables reach comfortably through the table's entire range of motion.
CONGRATULATIONS! YOUR ELEVATE TABLE ASSEMBLY IS COMPLETE!

*300-5373-00*
300-5373-00
Anthro Corporation®| 10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: [phone] | email: [email protected] | anthro.com
Outside the U.S. | Tel: [phone] | Fax: [phone]
Warranty:
Elevate Single-surface Table has a Lifetime Warranty against manufacturing defects, two years for the electrical system. Cords and plugs are not warranted.
Notices:
Technology FurnitureTM and ElevateTM are trademarks of Anthro Corporation. Anthro reserves the right to modify the design and specifications without prior notice.