Anthro Space Pal User manual

Anthro®Space PalTM (Tall)
Assembly Instructions
Thank you for buying our Products!
Before beginning assembly of your Anthro Space Pal,
please take a moment to review the parts listed below
to verify that your shipment is complete.
Additionally, we have included the following items:
Hex Driver 5/32"........................................Qty.1 .........................375-5000-00
Hex Driver Bit 5/32" .................................Qty.1 .........................375-5003-00
Hex Key 1/4"...............................................Qty.1 .........................375-5024-00
Wax Stick...................................................Qty.1 ......................... 175-5034-00
8 oz. Rubber Mallet .................................Qty.1 ......................... 375-5022-00
It may be helpful to have a second person to assist in this
assembly procedure.
Questions? 1-800-325-3841
01–Additional Shelf........................ Qty. 1..................100-6366-xx
02–3 X 3 Shelf Brackets ............... Qty. 8..................225-5397-xx
03–Large Shelf................................. Qty. 1..................100-6365-xx
04–3/4”Wood Screws .................... Qty. 32 ..............325-5106-00
05–Caster Screws........................... Qty. 4.................325-5052-00
06–1.75” Large End Caps............ Qty. 2..................175-5021-xx
07–Caster Inserts ........................... Qty. 4.................525-1000-00
08–23/8” Locking Casters ................ Qty. 2.................150-5003-03
09–BaseTube Screws..................... Qty. 4.................325-5000-00
10–23/8” Non-Locking Casters ....... Qty. 2.................150-5002-03
11– BaseTubes ................................. Qty. 2..................125-5195-xx
Enclosed Parts List 12– Base Bracket ............................. Qty. 1..................225-5396-xx
13– Bracket Screws......................... Qty. 2.................325-5136-00
14– 23.875” Vertical Legs .............. Qty. 4..................125-5020-xx
15– 20.1” Extension Tubes............ Qty. 4..................625-5549-xx
16– 1.5” Small End Caps............... Qty. 4..................175-5020-xx
17– Support Screws........................ Qty. 24 ..............325-5010-00
Detailed views of all Hardware is provided with eachAssembly Step.
All Fastener quantities listed here are the minimum needed
for your Cart assembly. There may be a few extra
Fasteners included,which are not counted in the Parts List.
Anthro® Corporation Technology Furniture®10450 SW Manhasset Drive Tualatin, Oregon 97062
SAVE THESE INSTRUCTIONS! anthro.com
Step 8
NOTE: It may be helpful to have a second person assist in
this assembly Step.
Lay the remaining Leg assembly on the floor as shown.
Carefully rotate the Shelf Assembly (from Step 7) onto
the LegAssembly.
Loosely attach the Shelf Brackets (on the Additional
Shelf) to Hole 2 from the top of the Extension Tubes
using three Support Screws per Bracket.
Finally, loosely install three Support Screws into both
Shelf Brackets (on the Large Shelf).
Step 9
Carefully rotate your Cart onto the Castors. Align the
Base Bracket with the rear of the BaseTubes. Install one
Bracket Screw through each Base Bracket opening into
the BaseTube Star Nuts.
Tighten all Support, BaseTube, and Bracket Screws.
Step 10
Finally,pop the four 1.5” Small End Caps into the Extension
Tubes and two 1.75” Large End Caps into the BaseTubes.
Congratulations! Your assembly is complete.
Please return the enclosed Registration Card to receive
our product updates,new catalogs,and sale flyers.
Thank you for choosing Anthro!
01
02
15
03
14
04
05
06
07 08
09
10
11 12
13
1.5” Small End Cap
1.75” Large End Cap
Self Threading Screw
325-5010-00
(5/16-18 X 1”) Bracket Screw
325-5136-00
16
17
Locking Caster
TECHNOLOGY FURNITURE®
March 2002 Rev. A
Questions? 1-800-325-3841
Large Shelf
Additional Shelf

Anthro®Space PalTM
Assembly Instructions
Anthro® CorporationTechnology Furniture®10450 SW Manhasset Drive Tualatin, Oregon 97062
Step 1
Before proceeding, please review the Assembly
Instructions of all Anthro Products you purchased
and are planning to include in this installation.
Determine the best height for your Space Pal’s Large
Shelf. Generally, a 28” high work surface works well
for most people and equipment.
These instructions will place your Large Shelf 28” from
the floor.
Step 3
Install two Caster Inserts into each Base Tube and
secure with one Caster Screw per Insert.
Insert the Casters, (locking ones in front) into the
Caster Inserts.
NOTE: Make certain the BaseTube Star Nut is located to
the rear as shown.
anthro.com
Step 4
Loosely attach twoVertical Legs to each BaseTube
assembly (from Step 3) using two BaseTube Screws.
NOTE: Make certain the holes on each of the Legs are
oriented with the BaseTubes as shown.
Step 5
Place your Large Shelf with the laminate face down. Align
one Shelf Bracket with the four drilled openings as shown.
Install fourWood Screws through the Bracket into the Shelf.
Repeat for the remaining seven Shelf Brackets.
Step 6
Lay oneVertical Leg assembly (from Step 4) onto the
floor. Position the Shelf Brackets (on the Large Shelf)
with Hole 2 from the top of eachVertical Leg and
loosely attach using three Support Screws per Bracket.
This will result in a 28” high work surface.
For a Large Shelf final height that is higher or lower
than 28”, refer to the Leg illustration shown at the far
right to determine which hole to attach your Shelf.
Questions? 1-800-325-3841
Base Tube Screw
325-5000-00
Support Screw
325-5010-00
Support Screw
325-5010-00
Locking
Caster
Star Nut
28”
Castor Screw
(small pink patch on end)
325-5052-00
Coped end
Top of Leg
Step 2
Rub the suppliedWax Stick over the Sleeve of each
ExtensionTube.
Next, Rotate the Extension Tube until the holes line
up with those on the Leg then insert the Sleeve into
the top of one of the Legs. Repeat for the remaining
four Legs.
NOTE: It may be helpful to tap the ExtensionTube into
the Leg with the Rubber Mallet.
Hole 3=27”
Hole 4=26”
Hole 5=25”
Hole 2=28”
Hole 1=29”
Hole 1=32”
(of the ExtensionTube)
Step 7
Position the Additional Shelf onto the Leg Assembly
(from Step 6).
Loosely attach the two Shelf Brackets to Hole 2 from
the top of each Extension Tube using three Support
Screws per Bracket.
Locking Caster
Locking Caster Locking Caster
Holes face inward
3/4”Wood Screw
325-5106-00
Top of the Vertical Leg is where the
ExtensionTube meets the Leg
Sleeve