Anthro fit 24 User manual

R
01–Worksurface
...............................
Qty. 1
.......................
(see below)
24” Wide Worksurface
(F24029zz/xx3)
............
100-6527-00
30” Wide Worksurface
(F3029zz/xx3)
...............
100-6432-00
36” Wide Worksurface
(F3629zz/xx3)
...............
100-6433-00
48” Wide Worksurface
(F4829zz/xx3)
...............
100-6417-00
02– Support Bracket-B
....................
Qty. 1
...................
225-2296-00
fi t
Small Support Y
fi t Small Support Y fi t
(F2429zz/xx3)
..
Qty. 1
...................
225-2015-00
03– 22.875” Vertical Legs
.................
Qty. 4
...................
125-5213-00
04– Base Tubes
.......................................
Qty. 2
..................
125-5273-00
05– Cross Tubes
................................
Qty. 2
.......................
(see below)
24” Deep Base Tube
(F2429zz/xx3)
....................
125-5218-00
30” Deep Base Tube
(F3029zz/xx3)
....................
125-5219-00
36” Deep Base Tube
F3629zz/xx3)
......................
125-5220-00
48” Deep Base Tube
(F4829zz/xx3)
....................
125-5214-00
06– Insert Screws
.............................
Qty. 4
...................
325-5052-00
07– 2” Large End Caps
....................
Qty. 4
...................
175-5157-00
08– 3” Locking Casters
...................
Qty. 2
...................
150-5053-00
09– Caster Inserts
............................
Qty. 4
...................
525-5032-00
Component list for part #’s
F2429zz/xx3, F3029zz/xx3,
F3629zz/xx3 & F4829zz/xx3
10–
5
/
16
-18
fi t
Bolts
..........................
...................
325-5194-00
11–
fi t
Tube Washers
.......................
Qty. 8
..
225-2050-00 or 225-3522-00
12– 3” Non-Locking Casters
.........
Qty. 2
...................
150-5052-00
13–
3
/
4
” Wood Screws
......................
Qty. 8
...................
325-5106-00
14– Support Bracket-A
....................
Qty. 1
.................
225-2295 -00
fi t
Small Support X
fi t Small Support X fi t
(F2429zz/xx3)
..
Qty. 1
...................
225-2014-00
15– Support Screws
.........................
Qty. 8
...................
325-5010-00
16– 1.5” Small Caps
.........................
Qty. 4
...................
175-5156-00
17– Back Trough
................................
Qty. 1
.......................
(see below)
24” Wide Back Trough
(F2429zz/xx3)
................
225-2289-00
30” Wide Back Trough
(F3029zz/xx3)
................
225-2290-00
36” Wide Back Trough
(F3629zz/xx3)
................
225-2291-00
48” Wide Back Trough
(F4829zz/xx3)
................
225-2292-00
18–
1
/
4
-20 Button Head Screws
....
Qty. 4
...................
325-5003-00
All Screw quantities listed here are the minimum needed
for your Standard Unit assembly. There may be a few extra
Screws included, which are not counted in the Parts List.
Anthro
Corporation Technology Furniture
®
10450 SW Manhasset Drive Tualatin, Oregon 97062 anthro.com
SAVE THESE INSTRUCTIONS!
Rev. D January 2006
Step 8
Align the Base Assembly on the Vertical Tubes as shown.
Secure the Base Assembly by inserting a
fi t
Bolt through a
Tube Washer. Then insert the Bolt through the Base Tube
and carefully thread it into the Vertical Tubes.
Repeat for the remaining three Bolts and tighten all Bolts.
Step 9
Insert the four 1.5” Small End Caps into the Vertical Legs.
Congratulations!
Your assembly is complete.
Please return the enclosed Registration Card to receive
our product updates, new catalogs, and sale fl yers.
Thank you for choosing Anthro!
Hello! Thank you for choosing Anthro.
Before beginning assembly of your Standard
Unit, please take a moment to review the
parts listed below to verify that your
shipment is complete.
Please review the assembly instructions
of all Anthro products you purchased and
are planning to include in this installation,
prior to beginning this assembly.
To make the assembly of your Standard
Unit even easier, we have included all of
the required tools. The handy Hex Driver
Bit can be used in your electric drill in place
of the Hex Driver.
Hex Driver
5
/
32
”
.........
375-5000-00
Hex Driver Bit
5
/
32
”
....
375-5003-00
8 oz. Rubber Mallet
....
375-5022-00
Questions?
1-800-325-3841
1.5” Small End Cap
(
5
/
16
-18 X 3.5”)
fi t
Bolt
325-5194-00
fi t
Tube Washer
225-2050-00 or 225-3522-00
04
06
07
05
01
13
14
18
fi t Bolt
fi t Bolt
fi t Tube
Washer
Cross Tube
24”/30”/36”/48” wide Standard Unit
Assembly Instructions
1-800-325-3841
NOTE: Detailed views of all Hardware are
provided with each Assembly Step.
Step 7
Attach a Cross Tube to a Base Tube by inserting a
fi t
Bolt
through a Tube Washer, then insert the Bolt through
the
Base Tube and carefully thread into the Cross Tube.
Repeat this procedure for other Cross Tube. Then tighten
all
fi t
Bolts.
fi t
Tube Washer
225-2050-00 or 225-3522-00
Cross Tube
fi t Tube
Washer
(
5
/
16
-18 X 3.5”)
fi t
Bolt
325-5194-00
fi t Bolt
Base Assembly

Anthro
Corporation Technology Furniture
®
10450 SW Manhasset Drive Tualatin, Oregon 97062
Step 1
Place your Worksurface onto the fl oor with the pre-
drilled holes facing upward.
Position the Support Brackets onto the Worksurface and
align two of the holes on each Support Bracket with the
predrilled holes on the Worksurface.
Loosely
secure each Support Bracket to the Worksurface
using two Wood Screws per Support Bracket.
NOTE:
fi t
Small Support X & Y, to be used in place of the
Support Brackets
(24” only).
anthro.com
Step 4
Attach a Vertical Leg by
installing two Support Screws
through the Support Bracket-A into holes 1 & 3 from the
top
(non-coped end)
of a Leg.
Repeat for the second Vertical Leg to be installed to
Support Bracket-A.
Step 6
Insert two End Caps into the ends of both Base Tubes.
Install two Caster Inserts into each Base Tube and
secure with one Insert Screw per Insert.
Insert one Locking and one Non-Locking Caster into
each Caster Insert of a Base Tube as shown.
Questions? 1-800-325-3841
Support Screw
325-5010-00
Step 2
Place the Back Trough onto the Worksurface, between the
installed Support Brackets
(from Step 1)
.
Align the two threaded holes on each end of the Back
Trough with those on both Support Brackets. Carefully,
thread one Button Head Screw through the Support
Bracket, into the Back Trough. Repeat for remaining three
Button Head Screws.
Insert two Wood Screws through the two remaining holes
on the Back Trough fl ange
(which should be aligned with two
predrilled holes on the Worksurface)
and tighten into place.
Step 5
Attach the remaining Vertical Legs to Support Bracket-B
using the same procedure used in Step 5.
NOTE: Make certain to install the Vertical Legs into the same
holes used in Step 5.
Support Screw
325-5010-00
3
/
4
” Wood Screw
325-5106-00
3
/
4
” Wood Screw
325-5106-00
(
1
/
4
-20 X .50”) Button Head Screw
325-5003-00
Insert Screw
(with pink threads)
325-5052-00
Locking
Caster
Support Bracket-B
FIRST
: Install the Button Head Screws
FIRST: Install the Button Head ScrewsFIRST
SECOND:
Install the Wood Screws
Back Trough
SECOND:
Back Support Flange
Support Bracket-A
Support Bracket-B
Caster Inserts placed
into the large holes
Leave these two side holes open
Non-Locking
Caster
Hole 1=29” Final Worksurface Height
Support Bracket-A
Support Bracket-B
Hole 1
Top
(non-coped)
(non-coped)
end
Bottom
(coped)
end
Hole 3
Hole 1
Hole 3
Top
(non-coped)
end
Bottom
(coped)
end
NOTE
: Make certain to install the Back
Trough in front of the Support Brackets
Threaded Holes
24”/30”/36”/48” Standard Unit
Assembly Instructions
fi t Small Support X & Y
(24” Standard Unit Only)
Step 3
Determine the best height for your Worksurface. These
instructions will place your Worksurface 29” from the
fl oor using the standard 3” casters.
For a fi nal Worksurface height that is lower than 29”,
adjust one hole down for each inch of variance desired.
NOTE: Your Worksurface location may be changed after your
Standard Unit has been completely assembled by repeating
Steps 5 & 6.
29”