Anthro eNook II User manual

ASSEMBLY INSTRUCTIONS
Anthro Corporation®| 10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: [phone] | email: [email protected] | anthro.com
Outside the U.S. | Tel: [phone] | Fax: [phone]
eNook®II
January 2007
Part Number: EK3616zz/xx
NOTE: The eNook additional shelves shown above are not included.

WELCOME
Thank you for purchasing eNook®!
This installation is a two person job.
If you have any questions or if we
can help you in any way, please
contact us at 800.325.3841.
NOTE: We provide do-it-yourself
hardware and instructions for
installation to wood studs and dry
wall. Your eNook can be mounted
to other surfaces (like concrete
and brick), and this work should be
done by a qualified contractor.
PARTS LIST
These instructions are for Anthro’s eNook.™ Before beginning
assembly, please take a moment to review the parts list below
to verify that your shipment is complete.
The following tools are required but not included:
¡Power Drill
¡1/8" drill bit (for mounting to wood wall studs)
¡1/2" drill bit (for mounting to drywall)
¡Phillips screwdriver (or Phillips bit for your drill)
¡Level
¡Stud Finder (for mounting to drywall)
2
Product Quantity Part Number
01 eNook Wall Frame 1 225-2247-23
02 6 Outlet Surge Protector 1 400-5190-06
03 1.5" Screws 4 325-5358-00
04 Workstation Screws 4 325-5092-00
05 3/8" Screw 1 325-5172-00
06 Cable Clips 6 175-5217-00
07 Toggle Bolt Dry Wall Anchor 4 325-5394-00
08 1-5/8" Screws 4 325-5086-00
09 Anthro Hex Driver (not shown) 1 375-5000-00
10 Cross Tray 1 225-2408-23
11 Main Unit 1 835-5200-xx
12 Pinch Cover 2 225-2418-23
13 Tack Board 1 100-6603-xx
14 Tack Clip 1 225-2424-23
08
01
02
06
04
03
05
07
12
14
10
11
13

eNook®Assembly Instructions 3
STEP 1
Select the Mounting Location
¡When choosing the right place to install your eNook, be sure to check the location of your power source. The power cord
that comes with your eNook is 6 ft long.
¡Your eNook can be mounted to drywall or to wood wall studs. If you’re installing to wood wall studs, go to Step 2.
¡If you’re installing into drywall, go to Step 7
STEP 2
Find Wall Studs
¡Using a stud finder, locate the studs to which you'll attach your eNook.
STEP 4
Attach Screws to Wall Studs
¡Using a 1/8" drill bit, drill one hole in a stud about
1-1/2" deep. How do you make sure that hole is
1-1/2" deep? Measure that length on your drill
bit and mark it with a piece of masking tape. Stop
drilling when you reach the masking tape.
¡Using a Phillips driver (or a power driver with a
Phillips bit), attach the first 1-1/2" long screw at that
mounting point, but don’t tighten all the way to the
wall. Stop tightening when the screw head is about
1/4" away from wall.
Drill
Wall Stud Profile
1½" Tape ¼"
Screw
STEP 3
Determine Mounting Point
¡Determine the optimal desk height for your eNook.
Typical sitting height is about 29" high; typical
standing height is about 42" high.
¡Measure up 14-3/4" from the shelf height and mark
that point on one stud.
14.75"
23"

4Questions? Call us at 800.325.3841 or visit anthro.com. We’re happy to walk you through the assembly!
STEP 6
Attach Lower Screws to Studs
¡Once the frame is on the wall, mark the mounting points for lower screws into the same studs.
¡Using the 1/8" drill bit, drill one hole in each stud about 1-1/2" deep.
¡Attach the 1-1/2" long screws and tighten all four screws fully so that the Frame is snug against the wall.
Proceed to Step 11
STEP 5
Lift eNook Frame onto screws
¡Lift the eNook frame onto the first mounting screw.
Keyhole slots on the frame are spaced every 2", so you
can position the eNook where you want it.
¡While one person holds the eNook frame level, the
second person marks the installation point of the
second 1-1/2" long screw. Make sure that the second
screw goes into a stud, too!
¡Remove the frame from the wall and drill the second
hole with the 1/8" drill bit.
¡Using a Phillips driver, attach the second 1-1/2" long
screw. Stop tightening when the screw head is abut
1/4" away from the wall.
¡Lift the frame onto the two mounting screws.
STEP 7
Determine the Mounting Point on Drywall
¡Determine the optimal desk height for the eNook
work surface, refer to image for typical shelf heights.
¡Measure up 14-3/4" from the shelf height and mark
that point on one stud. That's the upper mounting
height.
¡Once you determine the right height for your eNook
mark one mounting point hole location. When
choosing the first mounting point, remember that the
two upper mounting points should be at least 16"
apart to keep the eNook stable. To help you visualize
where eNook will be on your wall, use the eNook
Frame as a template.
14.75"
23"

eNook®Assembly Instructions 5
STEP 8
Install one TOGGLER™ for Drywall Installation
¡Drill 1/2” diameter hole in your wall at the mounting
point.
¡Insert a TOGGLER into a hole, metal end first.
¡Pull the plastic ring end so the metal channel rests
flush behind the wall. With your other hand, slide the
plastic cap along the straps until the flange of the cap
is flush with the wall.
¡Place your thumb between the plastic straps. Push
side to side, snapping off the straps at the wall.
¡Insert a 1-5/8" long screw into the TOGGLER, but don’t
tighten all the way. Leave the bolt head about 1/4”
from the plastic cap.
STEP 9
Install remaining TOGGLERs
This is a two-person step!
¡Lift the eNook Frame onto the bolt. Using a level to
make sure that the Frame is level, mark the second
mounting point as shown. Be sure that you mark your
spot in the center of the small keyhole!
¡Mark the third and fourth mounting points along the
bottom hole array. Set aside the Frame.
¡Drill 1/2” diameter holes on the 2nd, 3rd, and
4th mounting points and install TOGGLERs as
instructed above.
A
B C D

6Questions? Call us at 800.325.3841 or visit anthro.com. We’re happy to walk you through the assembly!
STEP 11
Install Four Fasteners onto Main Unit
¡Using your Hex Driver, install two black
Workstation Screws onto the side walls, but
don’t tighten all the way. Stop tightening
when the screw head is about 1/4" from tight.
Workstation Screw
325-5092-00
STEP 12
Attach Main Unit to Frame
¡Open the top and bottom doors and
find the angle slots on the Frame.
¡Lift the Main Unit onto the Frame by
aligning the two Workstation Screws
on the Frame with the angle slots.
Make sure that both fasteners are
captured.
¡Using a 5/32" hex driver, tighten
down the workstation screws.
STEP 10
Insert Screw and Install Frame
¡Insert one 1-5/8" long screw into the top two TOGGLERs, but don’t tighten all the way. Leave the screw head about
1/4" from the plastic cap.
¡Lift the Frame onto the top two screws. Install the bottom two screws, then tighten down all four screws.

eNook®Assembly Instructions 7
STEP 13
Insert the Bottom Tray
¡Place the Bottom Tray on the eNook shelf
so that the logo on the tray faces out.
¡Align the 2 holes on the back of the
Tray with the pins on the Frame.
¡Slide the Tray into place. Attach the tray
to the left and right of the frame using 4
workstation screws. Do not tighten these
screws all the way.
¡Install the cover plates, one on the left
and one on the right of the Tray. Slide
each Plate over the two workstation
screws, then down to insert the tabs on
the Plate into the notches on the Tray.
Tighten the workstation screws.
STEP 14
Insert the Back Panel
¡Hold the Back Panel so that the fabric-covered
side is facing you, long side up.
¡Place the Panel into the eNook so that the bottom
edge is resting on the bottom of the frame.
¡Tip the top of the Panel into place and secure with
the Tack Board Clip and a 3/8" Phillips head screw
inserted through the top of the Frame.
Pins
Workstation Screw
325-5092-00
3/8" Phillips Head Screw
325-5172-00
Tab
Notch

8Questions? Call us at 800.325.3841 or visit anthro.com. We’re happy to walk you through the assembly!
STEP 16
Insert Cable Clips
¡Cable Clips are provided to help manage
your cables. Clips can be poked into any
of the ventilation holes on the top, back,
or side of eNook.
¡Twist the ends of the clips to keep the
cables in place.
Congratulations! Your assembly is complete!
STEP 15
Insert Power Strip
¡Open the bottom door on eNook and
slide the Power Strip inside.

*300-5394-00*
300-5394-00
Anthro Corporation®| 10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: [phone] | email: [email protected] | anthro.com
Outside the U.S. | Tel: [phone] | Fax: [phone]
Warranty:
eNook has a five year warranty.
Notices:
Technology Furniture and eNook are trademarks of Anthro Corporation. Patent Pending. Anthro reserves the right to modify the design and specifications without prior notice.