Anthro Elevate II User manual

ASSEMBLY INSTRUCTIONS
Anthro Corporation®| 10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: [phone] | email: [email protected] | anthro.com
Outside the U.S. | Tel: [phone] | Fax: [phone]
Elevate II
August, 2012

WELCOME
Thank you for purchasing Anthro's Elevate II
electric lift table!
If you have any questions or if we can
help you in any way, please contact us at
800.325.3841.
TOOLS
Your Elevate II comes with these tools:
• 5/32" hex Anthro driver
• 5/32" hex driver bit
• 5mm hex key
• 1/8" hex key
• 3-way wrench
To make the assembly even easier, use your
own 3/8" socket for Step 4.
PARTS LIST
Before beginning assembly of your table, please review the
parts list to verify that your shipment is complete.
2
# Component Quantity Part Number
01 Worksurface 1
48w 23.25d Basic 100-6673-00
48w 23.25d Plus 101-1109-03-00
48w 29d Basic 100-6675-00
48w 29d Plus 101-1108-03-00
60w 23.25d Basic 100-6672-00
60w 23.25 Plus 101-1105-03-00
60w 29d Basic 100-6674-00
60w 29d Plus 101-1107-03-00
02 Gusset X (not shown) 1 225-4611-00
03 Gusset Y 1 225-4612-00
04 Electric Leg 2 575-5085-00
05 Motor Housing 2 225-4613-00
06 Cross Pan 1
48w 225-4619-00
60w 225-4615-00
07 Cable Tray 1
48w 23.25d 225-4638-00
48w 29d 225-4625-00
60w 23.25d 225-4637-00
60w 29d 225-4624-00
08 Control Box 1 400-5182-00
09 Power Cord (not shown) 1 400-5181-00
10 Key Pad 1 400-5357-00
11 Key Pad Slider 1 400-5358-00
12 Foot 2 835-5556-00
13 1" Button-head MDF Screw 26 325-5580-00
14 M6-10 Button-head Screw 8 325-5503-00
15 M6x14 Flat-head Screw 4 325-5435-00
16 3/4" Phillips SMS Zinc Screw 4 325-5370-00
17 1/2" Button-hd Screw 3 325-5193-00
18 10-24 Nylock Nut 3 325-5186-00
19 M6-20 Cap Screw 8 325-5272-00
01
03
04
05 06
07
08
10 11
12
13
19

Elevate II Assembly Instructions 3
STEP 1 - ATTACH GUSSETS TO TOP
Lay the top surface upside down on a cushioned, non-marring surface. Locate
the front edge of the table. On Plus tables, the front of the table has a sloping
waterfall edge. On the Basic tables, the back edge of the table has the seam
where the edgebanding meets.
Align the Leg Gussets with the holes on the top so the upright flange faces the
outside of the table and the tapering end points to the front of the table.
Attach each gusset to the top with six 1" MDF Screws using the Anthro driver.
STEP 2 - INSTALL LEGS
Align one Leg over one Leg Gusset so the cord feeds out of the leg toward the
center of the table (Image A). Slide a Leg Housing over the leg and slide it
down until the six screw holes on the housing line up with the pre-drilled holes
on the top (Image B). Loosely attach the housing to the top with six 1" MDF
Screws (325-5580-00) using the Anthro driver. From the front of the table,
attach the housing to the leg with four button-head fasteners (325-5503-00)
using the Anthro driver. Tilt the leg slightly to align the holes (Image C).
Repeat for the other leg and housing.
1” Btn-Hd Screw
325-5580-00
A B
C
M6-10 Button-head Screw
325-5503-00
STEP 3 - INSTALL THE CROSS PAN
Align the Cross Pan with the Leg Assemblies so the pair of flanges
on the pan line up with the pre-drilled holes on the table. Attach
the pan to the top with four 1" MDF Screws (325-5580-00) using
the Anthro driver.
Attach the pan to each leg housing with two M6x14 flat-head
fasteners using the Anthro driver.
FOR DEEP TABLES, GO TO STEP 4A. FOR SHALLOW TABLES, GO TO STEP 4B.
1” Btn-Hd Screw
325-5580-00
1” Btn-Hd Screw
325-5580-00
M6x14 Flat Hd Screw
325-5435-00
STEP 4A - INSTALL CONTROL BOX AND KEYPAD - DEEP TABLES
Align the Control Box with the four pre-drilled holes behind the cross pan so
that the ports on the box face the front of the table. Attach the Control Box to
the shelf with four 1" MDF Screws (325-5580-00) using the Anthro driver.
The keypad can be installed on the left or the right. Choose a location, just
remember that the table's upside down now, so when you flip the table over,
the keypad will be on the opposite side. Align the keypad and its housing with
the four pre-drilled holes at the front of the keyboard surface so the buttons
are face-down at the front edge of the keyboard surface and the flat side of the
housing is against the shelf. Using four Phillips Head Screws, attach the keypad
and its housing to the front of the worksurface. Go to Step 5.
1” Btn-Hd Screw
325-5580-00 3/4” Phillips Screw
325-5370-00

*300-5577-00*
300-5577-00
Anthro Corporation®| 10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: [phone] | email: [email protected] | anthro.com
Outside the U.S. | Tel: [phone] | Fax: [phone]
Warranty:
The Elevate II electric lift table has a Lifetime Warranty against manufacturing defects on the
table, 5 years on the legs and electrical system. Cords and plugs are not warranted.
Notices:
Technology Furniture and Elevate II are trademarks of Anthro Corporation. Anthro reserves the
right to modify the design and specifications without prior notice.
M6-20 Cap Screw
325-5272-00
STEP 4B - INSTALL CONTROL BOX AND KEYPAD - SHALLOW TABLES
The keypad can be installed on the left or the right. Choose a location, just
remember that the table's upside down now, so when you flip the table over,
the keypad will be on the opposite side. Align the keypad and its housing with
the four pre-drilled holes at the front of the keyboard surface so the buttons
are face-down at the front edge of the keyboard surface and the flat side of the
housing is against the shelf. Using four Phillips Head Screws, attach the keypad
and its housing to the front of the worksurface.
Align the Control Box with the four pre-drilled holes behind the cross pan so
that the ports on the box face the front of the table. Attach the Control Box to
the shelf with four 1" MDF Screws (325-5580-00) using the Anthro driver.
STEP 5 - INSTALL CABLE TRAY
Align the Cable Tray with the back of the table so the holes on the top flange of
the cross pan line up with the holes on the cable tray. While one person holds
the tray in place, attach the tray to the pan with nuts and screws using your
own 3/8" socket (or the 3-way wrench provided) and the smallest hex key (1/8")
in your kit.
Use the provided cable clips to route and organize cords.
1” Btn-Hd Screw
325-5580-00 3/4” Phillips Screw
325-5370-00
Nylock Nuts
325-5186-00
1/2”Button-hd Screw
325-5193-00
STEP 6 - INSTALL FEET AND HOME THE LEGS
Align one foot with each leg so the wheels are at the back. Attach the foot to
the leg with four M6x20 Socket-head Screws using the Anthro driver. Repeat
for the other foot.
With the help of another person, carefully rotate the table onto its feet. Plug in
the table and use the keypad to move the table all the way down. Release the
button and press it again to Home the legs.
Add your equipment and route cords into the cable tray. Carefully move the
table through its entire range of motion to be sure that your power and data
cables are long enough.
CONGRATULATIONS! YOUR ELEVATE II ASSEMBLY IS COMPLETE!