Anyload ES-HB Series User manual

Anyload Transducer Co. Ltd
Website: www.anyload.com
Email: in[email protected]
Fax: [phone]
North America Toll Free: 1-855-ANYLOAD (269 5623)
ES-HB
Series
Precision Balance
Product Manual (V1611)

TABLE OF CONTENTS
1. Introduction 2
2. Safety Recommendations 2
3. Structure Diagram 3
4. Display and Keys 4
5. Adaptor 4
6. Operation 4
6.1 ON/OFF the machine 4
6.2 Weighing Method 5
6.3 Calibration 5
6.3.1 Sensitivity Calibration 5
6.3.2 Linear Calibration 5
6.4 Counting Function 5
6.5 Percentage Setting Function 6
6.6 Backlight Function 6
6.7 Unit Selection 6
7. RS232 Communication 6
8. Troubleshooting 7
1| ANYLOAD ES-HB Precision Balance Product Manual (V1611)

1. Introduction
Thank you for purchasing and using the ES-HB series balances. The ES-HB
balances are equipped with weigh and measure with high precision load cell,
microcomputer and big liquid crystal display screen which have the advantages
of simple operations, speedy weighing, accuracy, stability, and much more.
Please read this manual carefully before using this product, in order to make full
use of this product with the functions and the troubleshooting to help you. You
can secure a copy of this manual at our website at www.anyload.com
2. Safety Recommendations
When using this weighing equipment the following
recommendations shall be observed for safety:
The weighing machine may only be used with the power adapter
supplied exclusively for use with the weighing machine.
Before inserting the power adapter, the user must ensure that
the operating voltage stated on the power adapter agrees with
the mains voltage.
If not, please contact Customer Service at the address above.
If the power adapter or its cable is damaged, the
weighing machine must immediately be disconnected
from the electricity supply (pull out the power adapter).
The weighing machine may only be operated from mains electricity
supply with a power adapter which is in perfect condition.
If there should be any reason to believe that it is no longer possible
to operate the weighing machine without danger, the weighing
machine is to be immediately unplugged from the electricity supply
(pull out power adapter) and secured against inadvertent operation.
The weighing machine must not be operated in an area subject to
explosion risks.
2| ANYLOAD ES-HB Precision Balance Product Manual (V1611)

4
3
2
6
1
7
8
9
5
Care must be taken when weighing liquids to ensure that no liquid is
spilt into the inside of the weighing machine or into connections on
the rear of the equipment or the power adapter. If liquid is spilt on the
weighing machine, it must immediately be unplugged from the mains
electricity supply (pull out power adapter). The weighing machine may
only be operated again after it has first been re-checked by a service
technician.
These instructions must be read by each operator of the equipment and must
be available at the workplace at all times.
3. Structure Diagram
code
name
code
name
1
adjust foot
2
Key
3
Display
4
platform
6
Level
7
The power socket
8
RS232C interface
9
Kensington lock
hole
5
Body
3| ANYLOAD ES-HB Precision Balance Product Manual (V1611)

4. Display and Keys
(1) (2) (3) (4) (5) (6)
KEY
FUNCTION
ASCII CODE
(1)
ON/ OFF the machine
Ox4F+OxOD+OxOA
(2)
Calibrate the machine
Ox43+0xOD+OxOA
(3)
Exchange units
Ox55+0xOD+OxOA
(4)
Backlight mode switch
Ox4D+OxOD+OxOA
(5)
Date print
Ox50+0xOD+OxOA
(6)
Zero and tare
Ox54+0xOD+OxOA
5. Adaptor
DC 6V/ 200mA adaptor
6. Operation
6.1 ON/OFF the machine
With no load on the platform, Put the round plug of AC adapter into the square
hole on the back of the balance, then put AC adapter into an alternating outlet,
or install 6 alkaline batteries AA SIZE in the battery holder at the bottom of the
balance (pay attention to the Plus(+) and minus(-) ends), press the key to
turn on the balance, and the balance will display the capacity and
division and then will show “0” Press to zero and,
Normal weighing can be started on, Press to t urn off the balance
4| ANYLOAD ES-HB Precision Balance Product Manual (V1611)

6.2. Weighing Method
With no load on the platform , Press to zero, and the balance will display
"0", Put the object on the platform. Wait until the unit "g" appears and the
reading value becomes stable, then the weight can be read.
6.3. Calibration
6.3.1. Sensitivity calibration
First, take away the object from the platform. Then, press key,
the balance will display "CAL" and then press key, "0.00" will show and
then the calibrating weight value will be shown, put the corresponding
calibrating weight on the center of the platform according to the shown weight
value. In a few seconds the display will stop, and meanwhile the calibrating
weight value will be shown, indicating that calibration is over. Normal weighing
can be started on. and the percentage of the state will increase from 0% to
100%, indicating that calibration is over. Normal weighing can be started on
6.3.2. Linear calibration
First, take away the object from the platform. Then press key, the balance
will display "CAL" and then press key switch to "LINE", then press
key and "0.00"will show and then the calibrating weight value will be shown,
put the corresponding calibrating weight on the center of the platform
according to the shown weight value. In a few seconds, the display will stop,
and the percentage of the state will increase from 0% to1 00%, indicating that
calibration is over. Normal weighing can be started on.
6.4 Counting Function ( pcs )
Press key to switch to "pcs", and the balance enters the counting state. If
you need resample for counting, please take away the object from the platform,
and press key, the balance will display "0",then press key, "PCS=xxx"
will display, "xxx" indicate the quantity value of samples, and press key to
change the quantity value , then put the same quantity sample on the platform
, then press key to confirm, when the reading value becomes stable,
Normal counting and weighing can be started on.
NOTE: If the balance displays "no", that indicates the samples' weight is too
light
5| ANYLOAD ES-HB Precision Balance Product Manual (V1611)

6.5 Percentage Setting Function
Press key to switch to "%" and enter percentage weighing ; if you need
resample, please take away the object from the platform, and press key to
display"0", then press key to display "PEr=xxx", and "xxx" indicates the
percentage value of sample, press key to change the value , and put the
same percentage samples on the centre of platform, press to confirm ,
when the reading value becomes stable, Normal percentage and weighing can
be started on.
NOTE: If the balance displays "no", that indicates the samples' weight is too
light
6.6. Backlight Function
Press key to sw1tch backlight, "ON" indicates backlight is always on,
"oFF" indicates backlight is always off, and "Auto" indicate backlight is auto
6. 7. Unit Selection
This balance has the function to select these units: g, kg, cL oz,
ozt, lb , I, tl, dwt, gn, pes , % Press to switch.
7. RS-232C Communication
RS232C interface: Connecting to PC or printer
Wiring diagram is as follows
Baud rate= 9600bps, check bit= None, data bit =8Bit,
stop bit=1 Bit, input instruction format please read "Key"
function; output data format: 7 bytes of data code +3 byte unit
code +2 byte end code, all the characters are ASCII code
6| ANYLOAD ES-HB Precision Balance Product Manual (V1611)

8. Troubleshooting
SYMPTOM
PROBABLE CAUSE
REMEDY
No Display
Power Adapter not
connected
Batteries are dead
Connect power Adapter
Replace batteries
Display
Batteries are weak
Replace batteries
Incorrect Weight
Reading
Balance was not set to zero
Balance has not been
correctly calibrated
With no load on the
platform press
Recalibrate the balance
Calibration
incorrect
Incorrect weights being
used
Use correct weights to
calibrate
Err 1
Over load
Stop weighing
immediately
7| ANYLOAD ES-HB Precision Balance Product Manual (V1611)