Anyload OCS Series User manual

OCS Series
Electronic Crane Scale
User’s Guide
OCSA3 & OCSA4 General Purpose Crane Scales
OCSB3 & OCSB4 Compact Crane Scales
OCSC3 & OCSC4 Enhanced Crane Scales
OCSG1 & OCSG2 Heat Resistant Crane Scales
OCSZ Heavy Duty Crane Scale

2 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide
TABLE OF CONTENTS
1. Safety Guides 4
2. Features 4
3. Specifications 5
4. Quick Start 5
Power On 5
Zero 7
Tare In 7
Tare Out 8
Hold 9
Power Off 10
5. User Input 10
Keys on Scale 11
Keys on Remote Controller 11
Input Numerals 12
6. Advanced Operations 12
Scale’s Mode 13
Weighing Mode 13
Gross/Net Mode 13
View Total Mode 14
Idle Mode 14
2ND Mode 15
Password Mode 16
Total 16
View Total 17
Delete Last Total 18
Clear Total 18
Display Unit Switch 19
Tare Set 21
Resolution Switch 22
Battery Check 23
System Setup 24
Resolution 25
Auto Power-Off Timing 25
Idle Timing 26

3 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide
Display Brightness 26
Display Frequency 26
Anti-Motion Level 27
Communication Setup 27
Communication On/Off 28
Baud Rate 28
Scale Address 29
Output Mode 29
7. Battery 30
8. Messages Illustration 31
9. Troubleshooting 32
10. Notes 33

4 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide
1. Safety Guides
For good performance and precise measurement on daily operation, observe
the following safety guides and maintenance recommendations:
oDo NOT overload the scale. This may damage the load cell and will void
the warranty.
oDo NOT leave the load hanged on the scale for too long. This will
decrease scale’s accuracy and shorten the load cell’s life span.
oInspect the shackle and hook before using. Check clips, pins and screws
properly fitted and installed.
oCheck battery frequently. When scale drained its battery, charge the
battery with its dedicated charger or replace it with a new one
oAvoid rotating the scale, this may damage the load cell
oDo NOT use scale under thunder or rain.
oHang the scale on shelf or in dry and well‐ventilated room. Do NOT put
the scale on the ground directly.
oDo NOT attempt to repair the scale by yourself. Contact your local
dealer or to the Technical Support.
2. Features
This scale is a combination of sound and proven mechanical design, with
nowadays’ most advanced electronics to provide a superb feature sets. It is
versatile, reliable, accurate and easy to operate.
oSuperb Quality. Strictly in accordance with OIML R76, Chinese
GB/T11883‐2002 National Standards, and European CE directives.
oGreat Safety. Aluminum‐casting case, high firm hook and ring,
dedicated weighing load cell for safety installation.
oStrong Reliability. Cutting‐edge technology, quality integrated circuit
for high performance and long time stability.
oBroad Applicability. Popular and applicable in storage, textile,
metallurgy industry, and so forth.
oEasy to Use. Ultra‐red remote controlling design. Easy to operate on
the scale or in distance.
oComplete Function. Division switch, unit conversion, automatic power
saver, battery inspection, idle mode, tare set, etc.

5 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide
3. Specifications
Accuracy Class
Chinese GB/T 11883‐2002 Class III
Equivalent to OIML R76
Tare Range
100% F.S.
Zero Range
4% F.S.
Stable Time
≤10sec
Overload
100% F.S. + 9e
Safety Load
125% F.S.
Ultimate Load
400% F.S.
Battery Life
80 hours ~ 200 hours with 6V/10Ah battery
60 hours ~ 100 hours with 6V/5Ah battery
Scale Battery
6V/10Ah or 6V/5Ah rechargeable battery
Op. Temp.
‐10℃~ +40℃
Op. Humidity
20℃≤90%
Display
1.5 inch (38.1mm) ultra‐luminance LED
1.2 inch (30mm) ultra‐luminance LED
4. Quick Start
This Quick Start will guide the user through these basic operations on the
crane scale. To make full use of this versatile scale, refer to Advanced
Operation section of this guide.
POWER ON
Action
oTo POWER ON the scale, press ON/OFF button on the scale for 1
second.
Function
oScale will go through power‐on test, battery check and initialization.
Condition
oPower‐on test is progressing when display flashes the following
characters twice. If scale doesn’t pass the test, error message will
display.

6 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide
oScale’s maximum capacity will display on the screen. For example, the
scale will show 5000kg if its full capacitywas set to 5000kg
oBattery Check will also be performed. If battery is working fine, the
screen flashes battery charge twice.
Refer to Battery section of this guide for more information about battery
recharging.
oFinally, the screen will show detection message while scale is detecting
its load and AUTO‐ZERO will function to ZERO status when the
AUTO‐ZERO function is enabled.
To learn more about Auto‐Zero function refer to Auto‐Zero Range in Scale’s
Configuration function.
After the scale is completely powered up and initialized, it is ready for weighing
operations.
NOTE:
Scale must be working at the battery voltage ranging from 6.8V to 5.8V.
Recharge the battery if needed.

7 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide
ZERO
Action
oTo ZERO the scale, press ZERO key on the scale or on remote
controller.
Function
oThe scale will set the current load to ZERO as if it has no load on it.
oThe ZERO indicator will light on (some models do not
have this zero indicator).
oThe weight reading becomes “0”, (or “0.0” or “0.00”, depending on the
resolution).
Condition
oThe scale must not in HOLD mode otherwise an error message
will display.
oThe scale must be stabled otherwise an error message will
display.
oCurrent weight reading shall be in MANUAL‐ZERO RANGE otherwise an
error message will display.
To learn more about Manual‐Zero Range refer to Scale’s Configuration function.
TARE IN
Action
oTo TARE IN a tare weight into the scale, press the TARE key
on scale or on remote controller (when the scale is in
GROSS MODE).
Function
oThe scale will store the tare weight and will shift to NET MODE. All
subsequent readings are deviated from the tare value.

8 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide
oThe TARE indicator will light on.
oThe weight reading shall turn to “0” (or “0.0” or “0.00”, depending on
the resolution).
Condition
oThe scale must not in HOLD mode otherwise an error message
will display.
oThe scale must be stabled otherwise an error message will
display.
oCurrent weight reading must be greater than 0 (or 0.0 or 0.00,
depending on the resolution). Otherwise an error message
will display.
oCurrent weight reading must be lesser than 100% scale’s MAXIMUM
CAPACITY otherwise an error message will display.
oThe scale must be in gross mode otherwise the action will treat as
TARE OUT.
TARE OUT
Action
oTo TARE OUT the tared weight from the scale, press TARE key on
scale or on remote controller ( the scale shall be in NET
MODE).
NOTE:
Setting or changing TARE will not affect the ZERO setting.
NOTE:
Taring will reduce the overloading range of the scale.
For example if a 1000kg container is tared on a 5000kg maximum
capacity scale, the new overload limit will become at 4018kg
[(5000 –1000) + 9 divisions].

9 | ANYLOAD OCS Series Electronic Crane Scale User’s Guide
Function
oThe scale shall clear the tare weight and shall return to gross
mode. It will display all subsequent readings in GROSS
MODE.
oThe TARE indicator will light off.
oThe weight reading is added with the tare weight.
Condition
oThe scale must not be in HOLD mode otherwise an error message
will display.
oThe scale must be in NET MODE otherwise the action will treat as TARE
IN.
HOLD
Action
oTo HOLD the weight reading, press HOLD key on scale or on
remote controller. Some models are not equipped with this
feature.
oTo unlock current reading, press HOLD key on scale or on
remote controller again.
Function
oThe HOLD indicator will light on.
oThe display will freeze at the held weight value even removing or
adding weights on the scale.
oPressing the HOLD key at HOLD mode, the indicator will
light off and the scale is unlocked. The scale will show the current
weight reading.
Condition
oTo HOLD the scale, it must be stabled otherwise an error message
will display
NOTE:
Scale can be unlocked anytime in HOLD mode.