Apex Digital Pro-care 2 User manual

Pro-care 2
User’s Manual

CONTENTS
ALTERNATING PRESSURE REDISTRIBUTION SYSTEM
USER’S MANUAL 1
SISTEMA DE REDISTRIBUCIÓN DE PRESIÓN ALTERNA
MANUAL DE INSTRUCCIONES 17
SISTEMA DE REDISTRIBUIÇÃO DE PRESSÃO ALTERNADA
INSTRUÇÕES DE UTILIZAÇÃO 33
SYSTÈME DE REDISTRIBUTION À PRESSION ALTERNÉE
INSTRUCTIONS D'UTILISATION 49
ALTERNIERENDES DRUCKUMVERTEILUNGSSYSTEM
GEBRAUCHSANLEITUNG 65
ALTERNEREND DRUKSYSTEEM
GEBRUIKERSHANDLEIDING 81
SISTEMA DI RIDISTRIBUZIONE A PRESSIONE ALTERNATA
MANUALE DI ISTRUZIONI 97
MODEL NO.: 9P-051500
PLEASE READ THE MANUAL BEFORE USE

Pro-care2/English 1
IMPORTANT SAFEGUARDS
READ ALL INSTRUCTIONS BEFORE USING
DANGER - To reduce the risk of electrocution:
1. Always unplug this product immediately after using.
2. Do not use while bathing.
3. Do not place or store this product where it can fall or be pulled into a tub or sink.
4. Do not place in or drop into water or other liquid.
5. Do not reach for a product that has fallen into water. Unplug immediately.
WARNING - To reduce the risk of burns, electrocution, fire, or injury to persons:
1. Evaluate patients for entrapment risk according to protocol and monitor patients appropriately.
2. The product may be used for patients with spinal injury, but suggested to consult with physician before
use. However, it should not be used for patients with unstable spinal fractures.
3. Close supervision is necessary when this product is used on or near children. Electrical burns or chok-
ing accident may result from a child swallowing a small part detached from the device.
4. Use this product only for its intended use as described in this manual. Do not use other mattress not
recommended by the manufacturer.
5. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the product to your supplier or Apex Medical Corp.
for examination and repair.
6. Keep the cord away from heated surfaces.
7. Never block any air openings of this product or place it on soft surfaces, such as a bed or couch, where
openings may be blocked. Keep the air opening free of lint, hair, and other similar particles.
8. Never drop or insert any object into any opening or hose.
9. Do not modify this equipment without authorization of the manufacturer.
10. Mattress covers have passed skin sensitization and skin irritation test. However, If you suspect that
you may have had or are having an allergic reaction, please consult a physician immediately.
11. Do not leave long lengths of tubing around the top of your bed. It could lead to strangulation.
CAUTION –
1. If there is a possibility of electro-magnetic interference with mobile phones, please increase the dis-
tance (3.3m) between devices or turn off the mobile phone.
NOTE, CAUTION AND WARNING STATEMENTS:
NOTE - Indicate some tips.
CAUTION - Indicate correct operating or maintenance procedures in order to prevent damage to or de-
struction of the equipment or other property
WARNING - Calls attention to a potential danger that requires correct procedures or practices in order to
prevent personal injury.

Pro-care2/English 2
SYMBOLS
Authorized representative in the European community.
Manufacturer
Complies with standards protecting against electric shock for type BF equip-
ment.
Consult operating instructions for use
Protected against solid foreign objects of 12.5 mm and greater; Protection
against vertically falling water drops
Class II
Temperature limitation/temperature range
Dry clean, Any Solvent Except Trichloroethylene
Do Not Iron
Tumble Dry, Normal, Low Heat
Do Not Tumble Dry
Do Not Bleach
Do Not Dry Clean
Machine wash, regular / normal, 95 degrees C (203 degrees F)
Attention – Observe
p
ro
p
er Dis
p
osal of Electrical & Electronic E
q
ui
p
ment
(WEEE): This product should be handed over to an appropriate collection point
for the recycling of electrical and electronic equipment. For more detailed in-
formation about the recycling of this product, please contact your local city
office, household waste disposal service or the retail store where you pur-
chased this product.

Pro-care2/English 3
1. Introduction
This manual should be used for initial set up of the system and for reference purposes.
1.1 General Information
The system is a high quality and affordable mattress system suitable for treatment and prevention
of pressure ulcers.
The system has been tested and successfully approved to the following standards:
IEC/EN 60601-1
IEC/EN 60601-1-2
IEC/EN 61000-3-2 Class A
IEC/EN 61000-3-3
CISPR 11 Group 1, Class B
EMC Warning Statement
This equipment has been tested and found to comply with the limits for medical devices to the EN
60601-1-2. These limits are designed to provide reasonable protection against harmful interference in a
typical medical installation. This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to other de-
vices in the vicinity. However, there is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to other devices, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
 Reorient or relocate the receiving device.
 Increase the separation between the equipment.
 Connect the equipment into an outlet on a circuit different from that to which the other device(s) are
connected.
 Consult the manufacturer or field service technician for help.
1.2 Intended Use
This product is intended to help and reduce the incidence of pressure ulcers while optimizing
patient comfort. It also provides following purposes:
 to help and reduce the incidence of pressure ulcers while optimizing patient comfort.
 for long term home care of patients suffering from pressure ulcers.
 for pain management as prescribed by a physician.
The product can only be operated by personnel who are qualified to perform general nursing
procedures and have received adequate training in knowledge of prevention and treatment of
pressure ulcer.
NOTE- Equipments are not suitable for use in the presence of flammable anesthetic
mixture with air or with oxygen or nitrous oxide.

Pro-care2/English 4
2. Product Description
Unpack the box to check for any damage which may have occurred during shipment. If there are damages,
please contact your dealer immediately.
2.1 Pump and Mattress System
1. CPR
2. Pump unit
3. Mattress System
4. Quick Connector
2.2 Pump Unit
Front
1. Quick Connector
2. Front Panel
Rear
1. Power Switch
2. Power Cord
3. Air Filter
4. Fuses
5. Mounting Brackets

Pro-care2/English 5
2.3 Front panel
1. Pressure Adjustment Knob
Pressure adjustment knob controls the air pressure output. When turning clockwise, the output pres-
sure will increase. Vice versa for decreasing air pressure. Higher pressure output will support the heavi-
er weight patient. The setting reference is given as Kg. Please consult your physician for a suitable set-
ting.
NOTE- Check if the pressure is suitable for the patient by sliding one hand beneath the air cells at
the level of the patient's buttocks. Always leave at least 1” inch space between patient and the
static cell to prevent bottoming out.
2. Normal Pressure Indicator
When green LED lights up, the pressure inside of air mattress reaches the preset pressure setting.
3. Low Pressure Indicator
When low pressure LED lights up, the pressure inside of air mattress is below normal. Please refer to
troubleshooting. During initial inflation of the mattress, the Low Pressure LED will illuminate until the
set pressure is reached.
4. Static Function
Press blue STATIC button to suspend alternating function, if needed. The pressure inside of air tubes
will be adjusted to the same softness. Press the STATIC button again; it will switch back to alternating
mode.
5. Alarm Mute
Press alarm mute button to temporary suspend the low-pressure alarm. If the situation did not resolve
in 3~5 mins, the alarm will resume again to notify the caregiver.
6. Power Failure Alarm (PFA)
During power failure situation, the PFA LED light and buzzer will notify caregivers to take appropriate
action. By pressing the alarm mute button both PFA buzzer and LED will cease.

Pro-care2/English 6
3. Installation
3.1 Pump & Mattress Installation
NOTE- Unpack the box to inspect for any damage which may have occurred during shipment. If there
are any damages, please contact your dealer immediately.
1 2 3
45 6
1. Place the mattress or pad on top of the bed frame. Please note for the foot end. There are securing
straps on the base of the mattress. Secure the mattress firmly by fixing the straps to the bed frame,
ensure that moving sections of the bed frame are still free to move.
WARNING- The Pro-care 2 mattress must be applied on the underlying mattress.
2. Hang the pump onto bed rail (foot-end), and adjust hangers to best upright position of the pump, or
place the pump on a flat surface.
3. Connect air hose connectors from air mattress to the pump unit. When a "click" sound is felt or heard,
the connection is completed and secured.
NOTE- Check and ensure the air hoses are not kinked or tucked under mattress.
4. Plug the power cord into electrical outlet.
NOTE- 1. Make sure the pump unit is suitable for the local power voltage.
2. The plug is also served to disconnect the device.
5. Then turn the main power switch to ON position.
CAUTION- The pump can only be applied to the mattress recommended by the manufacturer.
Do not use it for any other purpose. (Applied part: air mattress) Do not position the
equipment so that it is difficult to operate the disconnecting device.
6. The cable management loops are provided along the sides of the mattress to cover the mains power
cable. Please make sure the wire has no signs of damage. After installation, the extra length of the
power cord, if any, should be neatly managed to avoid causing a trip and should be clear of moving bed
mechanisms or other possible entrapment area.
The EQUIPMENT should be firmly placed at position where users/doctors can access easily.

Pro-care2/English 7
4. Operation
NOTE- Always read the operating instruction before use.
4.1 General operation
1 23
45
1. Switch on the main power switch found from the side of the pump.
2. The pump unit is to delivering air into mattress, wait least 30 mins for mattress to be inflated.
NOTE- Every time when mattress is first setup for use, it is recommended that the pressure knob to be
set to "Max" for the quickest inflation. User can then adjust air mattress to the desired soft-
ness afterward.
3. The low pressure indicator (yellow LED) will light up when the mattress is not fully inflated.
4. When the appropriate pressure is reached, the low pressure indicator (yellow LED) will go off and
normal pressure indicator (green LED) will light up automatically.
5. According to the weight and height of the patient, adjust the knob setting to the most comfortable
level without bottoming out, then the pressure in mattress will slowly increase to a certain value af-
ter the air mattress is ready to use.In an event of the power failure situation, the PFA will alarm. User
can disable by pressing the alarm mute button.

Pro-care2/English 8
4.2 Emergency CPR Operations
When there is an emergency to perform CPR on the
patient, quickly turn the CPR knob to release air from
mattress. The CPR knob is located at the head-end,
right-hand-side of the mattress. The quick connector
on the pump unit can be disconnected for even faster
deflation.
4.3 Transportation
NOTE- When there is a power outage or a need of
transporting the patient, one can capped
on the quick connector as shown on the
right to slow down the air leakage. De-
pending on the setting and mattress
height, the mattress can remain inflated for
awhile. If there is a bottom-out issue,
please remove the patient from deflating
mattress to another proper surface.

Pro-care2/English 9
5. Cleaning
It is important to follow the cleaning procedures to avoid cross contamination. Be sure to clean the surface
in a dry and dust free environment. Wipe down the pump unit with a damp cloth pre-soaked with a mild
detergent. Avoid contact with dust and proximity to dusty areas. Make sure that any cleaning agents you
use will not harm or corrode the plastic casing on the pump unit. If your doctor or medical facilities have
other special cleaning instruction, please follow the professional instruction.
CAUTION- Do not immerse or soak pump unit.
WARNING- Do not remove the housing of the pump to avoid the electrical shock. All disassembly or
repair should be done by professional technicians.
CAUTION- The pump does not need oil lubrication; please do not dissemble the system.
Cover Material:
 Stretch
 Silver+Stretch
Wipe-down the mattress unit with a damp cloth pre-soaked with warm water containing a mild detergent,
or chlorine bleach followed by an approved intermediate level disinfectant. Also the mattress top cover
can be completely removed for laundry with water temperature indicated on the laundry label; however, it
is recommended that the user still check with local policy to determine the time/ temperature ratio re-
quired achieving thermal disinfection. The cover may also be cleaned using sodium hypochlorite diluted in
water. After cleaning, please avoid dust and proximity to dusty areas and all parts should be air dried thor-
oughly before use.
CAUTION- Do not use phenolic based products for cleaning.
CAUTION- After cleaning, dry the mattress without direct exposure of sunlight.
6. Storage
1. To store the mattress, lay the mattress out flat and upsides down.
2. Roll from the head end towards the foot end with CPR valve open.
3. Foot-end strap can then be stretched around the rolled mattress to prevent unrolling.
NOTE- Do not kink, crease or stack the mattresses and do not store the system in direct sunlight,
high temperature or moisture area.

Pro-care2/English 10
7. Maintenance
7.1 General
1. Check main power cord and plug if there is abrasions or excessive wear.
2. Check mattress cover for signs of wear or damage. Ensure mattress cover and tubes are stubbed to-
gether correctly.
3. Check airflow from the quick connector. The airflow should alternate between each connector every
half-cycle time if it's in alternating mode.
4. Check the air hoses if there is kink or breaks. For replacement, please contact our local dealers.
7.2 Fuse Replacement
1. Disconnect the plug form mains power when a
blown fuse is suspected.
2. Remove the cover of the fuse holder by means of a
small screwdriver.
3. Insert a new fuse of the correct rating in, and re-
place the cover of the fuse holder back. The fuse
should be rated as T1AL/250V type and VDE ap-
proved.
7.3 Air Filter Replacement
1. Open the air filter cap located at the back of
pump.
2. Replace with a clean filter and put the cover lid
back. The filter is reusable and can be washed
gently with a mild detergent and water. Dry the
filter before use.
3. Check and replace air filter regularly if
environment is dirty. Suggested to do it every
three month.

Pro-care2/English 11
8. Expected Service Life:
The products are intended to offer safe and reliable operation when use or installed according to the
instructions provided by Apex Medical. Apex Medical recommends that the system be inspected and
serviced by authorized technicians if there are any signs of wear or concerns with device function and
indication on products. Otherwise, service and inspection of the devices generally should not be required.
9. Trouble Shooting
Q.1 Power is not ON
‧ Check if the plug is connected to mains.
‧ Check for a blown fuse.
Q2 Low Pressure Alarm is on
‧ Check if the Quick Connector is tightly secured.
‧ Check if all tubing connections along mattress are secured.
‧ Check if the air hoses are kinked or broken.
Q3 Power Failure Alarm is on
‧ Check if the power is suddenly shut down.
‧ Check if the power cord is connected properly.
Q4 Patient is bottoming out
‧ Pressure setting might be inadequate for the patient, adjust comfort range 1 to 2 levels higher and
wait for a few minutes for best comfort.
Q5 Mattress form is loose
‧ Check if all the snap buttons or straps of mattress are all securely fastened.
‧ Check if the mattress is fixed to the bed frame by straps.
Q6 No air produced from some air outlets of the air tube connector
‧ This is normal since there is alternating mode. Air outlets take turns to produce air during their cycle
time.
If the above information does not solve your problems, please contact your local agent directly. They might
require a technician to take care the problem.

Pro-care2/English 12
10. Technical Specification:
Item Specification
Power Supply (Note: See
rating label on the product) AC 220-240V 50 Hz, 0.07A (for 230V system)
Fuse Rating T1AL, 250V
Cycle time 15mins, Fixed, non-adjustable
Dimension (L x W x H) 29.1 x 20 x 11.7 cm /11.4" x 7.9" x 4.6"
Weight 2.2 Kg / 5 lb
Environment
Atmospheric
Pressure 700 hPa to 1013.25 hPa
Temperature
Operation: 10°C to 40°C (50°F to 104°F)
Storage: -15°C to 50°C (5°F to 122°F)
Shipping: -15°C to 70°C (5°F to 158°F)
Humidity
Operation: 10% to 90% non-condensing
Storage: 10% to 90% non-condensing
Shipping: 10 % to 90% non-condensing
Classification
Class II, Type BF, IP21
Applied Part: Air Mattress
Not suitable for use in the presence of a flammable
anesthetic mixture (No AP or APG protection)
Mattress Specification
Model 5” (12.7 cm ) Overlay Mattress
Dimension (L x W x H) 200x90x12.7cm/
78.7"x35.4"x 5"
200x85x12.5cm/
78.7”x33.5”x5”
200x80x12.5cm/
78.7”x32”x5”
Weight 7.3 Kg / 16.1 lb 7.1 Kg / 15.7 lb 7.0 Kg / 15.4 lb
Max. Support Weight 180 Kg / 396.8 lb
NOTE-
1. Consult the distributor or EU representative for further technical documents.
2. The specification is also suitable for other areas operating with same power supply.
3. Mattress dimension and weight is measured without foam cushion
4. The manufacturer reserves the right to modify the specification without notice.

Pro-care2/English 13
Appendix A: Emc Information
Guidance and Manufacturer’s Declaration- Electromagnetic Emissions:
This device is intended for use in the electromagnetic environment specified below. The user of this device
should make sure it is used in such an environment.
Emissions Test Compliance Electromagnetic Environment-Guidance
RF emissions
CISPR 11
Group1 The device uses RF energy only for its internal function. There-
fore, its RF emissions are very low and are not likely to cause
any interference in nearby electronic equipment
RF emissions
CISPR 11
Class B
The device is suitable for use in all establishments, including
domestic establishments and those directly connected to the
public low-voltage power supply network
Harmonic emissions
IEC61000-3-2 Class A
Voltage fluctuations /
Flicker emissions
IEC61000-3-3
Complies
Warning:
1.
The device should not be used adjacent to or stacked with other equipment. If adjacent or stacked use is neces-
sary, the device should be observed to verify normal operation in the configuration in which it will be used.
2. Use of accessories, transducers and cables other than those specified or provided by the manufac-
turer of this equipment could result in increased electromagnetic emissions or decreased electro-
magnetic immunity of this equipment and result in improper operation.
3. Portable RF communications equipment (including peripherals such as antenna cables and external
antennas) should be used no closer than 30 cm (12 inches) to any part of the Pump, including cables
specified by the manufacturer. Otherwise, degradation of the performance of this equipment could
result.

Pro-care2/English 14
Guidance and Manufacturer’s Declaration- Electromagnetic Immunity:
This device is intended for use in the electromagnetic environment specified below. The user of this device
should make sure it is used in such an environment.
Basic EMC stand-
ard
Immunity Test Levels
Compliance
Levels Electromagnetic Environ- ment-Guidance
Professional
healthcare
facility environment
HOME
HEALTHCARE
ENVIRONMENT
Electrostatic
Discharge (ESD)
IEC61000-4-2
±8kV contact
±15kV air ±8kV contact ±15kV air
Floors should be wood, con-
crete or ceramic tile. If floors
are covered with synthetic
material, the relative humidity
should be at least 30 %.
Electrical fast
transient/ burst
IEC61000-4-4
±2kV for power supply line
±1kV for input/output line
±2kV for
p
ower
supply line
±1kV for in-
put/output line
Mains power quality should be
that of atypical commercial or
hospital environment
Surge
IEC61000-4-5
± 1 kV line(s) to
line(s)
± 2 kV line(s) to
earth
± 1 kV line(s) to
line(s) ± 1 kV line(s) to line(s) Mains power quality should be
that of atypical commercial or
hospital environment.
Voltage dips,
short interrup-
tions and voltage
variations on
power supply
input lines
IEC61000-4-11
Voltage Dips:
i) 100% reduction for 0.5 period,
ii) 100% reduction for 1 period,
iii) 30% reduction for 25/30 period,
Voltage Interruptions:
100% reduction for 250/300 period
230 V
Mains
p
ower
q
ualit
y
should be
that of a typical commercial or
hospital environment. If the
user of this device requires
continued operation during
power mains interruptions, it
is recommended that the
device be powered from an
uninterruptible power supply
or a battery.
Power frequency
(50/60Hz) mag-
netic field
IEC61000-4-8
30 A/m 30 A/m 30 A/m
Power fre
q
uenc
y
ma
g
netic
fields should be at levels
characteristic of a typical
location in a typical commer-
cial or hospital environment.
Conducted RF
IEC 61000-4-6
3 Vrms
0,15 MHz – 80 MHz
6 Vrms in ISM bands
between 0,15 MHz
and 80 MHz
80 % AM at 1 kHz
3 Vrms
0,15 MHz – 80
MHz
6 Vrms in ISM and
amateur radio
bands between
0,15 MHz and 80
MHz
80 % AM at 1 kHz
6Vrms
Portable and mobile RF com-
munications equipment
should be used no closer to
any part of this device, in-
cluding cables, than there
commended separation dis-
tance calculated from the
equation applicable to the
frequency of the transmitter.
Recommended separation
distance
d=150kHz to 80MHz
d=0.6 80MHz to 800MHz
d=1.2 800 MHz to 2.7GHz
Radiated RF EM
Fields
IEC61000-4-3
3 V/m 80 MHz to
2.7 GHz
80 % AM at 1 kHz
385-6000 MHz,
9-28V/m, 80%
AM(1kHz) pulse
mode and other
modulation
10 V/m 80 MHz to
2,7 GHz
80 % AM at 1 kHz
385-6000 MHz,
9-28V/m, 80%
AM(1kHz) pulse
mode and other
modulation
10V/m

Pro-care2/English 15
Where P is the maximum out-
put power rating of the trans-
mitter in watts (W) according
to the transmitter manufac-
turer and d is the recom-
mended separation distance
in meters (m).b
Field strengths from fixed RF
transmitters, as determined
by an electromagnetic site
survey ,a should be less than
the compliance level in each
frequency ranged.
Interference may occur in the
vicinity of equipment marked
with the following symbol:
NOTE 1: UTis the a.c. mains voltage prior to the application of the test level
NOTE 2: At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE 3: These guidelines may not apply in all situations. Electromagnetic propagation is affected by ab-
sorption and reflection from structures, objects and people
a)Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones
and land
mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoret-
ically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an elec-
tromagnetic site survey should be considered. If the measured field strength in the location in which the
device is used exceeds the applicable RF compliance level above, the device should be observed to ver-
ify normal operation. If abnormal performance is observed, additional measures may be necessary, such
as reorienting or relocating the device.
b) Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 10 V/m.

Pro-care2/English 16
Recommended separation distances between portable and mobile RF communications equip-
ment and this device:
This device is intended for use in an electromagnetic environment in which radiated RF disturbances are
controlled. The customer or the user of this device can help prevent electromagnetic interference by
maintaining a minimum distance between portable and mobile RF communications equipment (transmit-
ters) and this device as recommended below, according to the maximum output power of the communica-
tions equipment
Rated maximum out-
put power
of transmitter
W
Separation distance according to frequency of transmitter m
150 kHz to 80 MHz
d=
80 MHz to 800 MHz
d=0.6
800 MHz to 2.7 GHz
d=1.2
0.01 0.1 0.06 0.12
0.1 0.31 0.19 0.38
1 1 0.6 1.2
10 3.1 1.9 3.8
100 10 6 12
For transmitters rated at a maximum output power not listed above, the recommended separation dis-
tance
d in meters (m) can be estimated using the equation applicable to the frequency of the transmitter,
where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter
manufacturer.
Note 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
Note 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by ab-
sorption and reflection from structures, objects, and people.

Pro-care2/Español 17
MEDIDAS DE SEGURIDAD IMPORTANTES
LEA LAS INSTRUCCIONES COMPLETAMENTE ANTES DE USARSE
PELIGRO - Para reducir el riesgo de descarga eléctrica:
1. Siempre desconecte este producto inmediatamente después de usarlo.
2. No lo use mientras se esté bañando.
3. No coloque o almacene el producto donde se pueda caer o ser halado hacia una bañera o lavamanos.
4. No lo coloque en agua o lo deje caer dentro de agua u otro líquido.
5. No trate de sacar un producto que haya caído en el agua. Desconéctelo inmediatamente.
ADVERTENCIA – Para reducir el riesgo de quemaduras, choque eléctrico, incendios o lesiones:
1. Evaluar el riesgo de que los pacientes queden atrapados de acuerdo con el protocolo de las
instalaciones y supervisarlos adecuadamente
2. El producto se puede utilizar para los pacientes con lesión de la médula, pero sugiere consultar con
el médico antes de usar. Sin embargo, no se debe utilizar para los pacientes con fracturas vertebrales
inestables.
3. Es necesario supervisarlo de cerca cuando lo utilizan menores de edad o se usa cerca de ellos
4. Utilice el producto solamente para lo que está diseñado tal y como se describe en este manual. No
utilice colchones no recomendados por el fabricante
5. Nunca utilice este producto si tiene uncable o enchufe dañado, no funciona correctamente, se ha
caído o se ha dañado o ha caído en el agua. Envíe el producto a un centro especializado para que lo
examinen y reparen
6. Mantenga el cable alejado de superficies calientes
7. Nunca bloquee las aberturas de aire de este producto ni lo coloque en una superficie blanda, como
por ejemplo una cama o un sofá, donde pueden quedar bloqueadas las aberturas. Mantenga las
aberturas libres de filamentos, pelos y otras partículas similares
8. No está permitido realizar ninguna modificación en este equipo.
9. No modificar este equipo sin la autorización del fabricante.
10. Las fundas del colchón han sido sometidas a la prueba de irritación y sensibilización de la piel. No
obstante, si sospecha que está teniendo o ha tenido una reacción alérgica, consulte
inmediatamente con el médico.
11. No dejar largos trozos de tubo en la parte superior de la cama. Podría provocar estrangulamiento.
PRECAUCIÓN -
1. Si hay una posibilidad de interferencia electromagnética con los teléfonos móviles, por favor,
aumentar la distancia (3,3 m) entre los dispositivos o apagar el teléfono móvil.
NOTAS, PRECAUCIONES y ADVERTENCIAS:
NOTA - Indica información útil, consejos, recordatorios.
PRECAUCIÓN - Indica la operación o procediminetos de mantenimiento correctos para evitar daños o la
destrucción del equipo u otra propiedad.
ADVERTENCIA - Indica un daño potencial que requiere de procedimientos operativos o de prácticas
correctas para evitar daños personales.