APV Tined Weeder Pro VS 600 M1 User manual

TRANSLATION OF THE ORIGINAL OPERATING MANUAL
Version: 1.1 EN / Item no.: 00601-3-874
Operating manual for the Tined Weeder Pro
VS 600 M1, VS 750 M1, VS 900 M1, VS 1200 M1
Please read carefully before initial operation!

Page 2 Original operating manual - APV Tined Weeder Pro
Table of contents
CE conformity............................................................................................................................... 3
1 Identification of the implement........................................................................................... 4
2 Service ................................................................................................................................. 5
3 Warranty............................................................................................................................... 5
4 Safety information............................................................................................................... 5
4.1 Intended use.............................................................................................................. 5
4.2 General safety-related instructions and accident prevention regulations .................... 6
4.3 Mounted implements.................................................................................................. 7
4.4 Hydraulic system........................................................................................................ 7
4.5 Maintenance .............................................................................................................. 8
4.6 Tyres.......................................................................................................................... 8
5 Safety signs ......................................................................................................................... 9
6 Operating instructions for the Tined Weeder Pro ........................................................... 11
6.1 Mounting on the tractor ............................................................................................ 11
6.2 Safe parking............................................................................................................. 11
6.3 Folding the Tined Weeder Pro ................................................................................. 11
6.4 Working position and setting the working depth ....................................................... 12
6.5 Hydraulic tine adjustment......................................................................................... 14
6.6 Additional adjustment options for ground adaptation................................................ 14
7 Maintenance and care....................................................................................................... 15
7.1 General maintenance instructions............................................................................ 15
7.2 Tine change............................................................................................................. 16
7.3 Changing the springs............................................................................................... 16
7.4 Repairs and service ................................................................................................. 18
8 Information on nature conservation and environmental protection.............................. 18
9 Technical data ................................................................................................................... 19
9.1 Harrow array widths ................................................................................................. 20
9.2 Combination options for the Tined Weeder Pro with pneumatic seeders.................. 21
10 Hydraulicdiagram .............................................................................................................. 22
11 Road transport of the Tined Weeder Pro......................................................................... 25
11.1 Transport on public roads (in general)...................................................................... 25
11.2 Calculation of the weight ratios ................................................................................ 26
11.3 Table for the weight ratios........................................................................................ 27
12 Lighting circuit diagram.................................................................................................... 28
13 Decommissioning, storage and disposal ........................................................................ 28
13.1 Decommissioning the implement ............................................................................. 28
13.2 Storage of the implement......................................................................................... 28
13.3 Disposal................................................................................................................... 28
14 Cropping tips for using the Tined Weeder Pro................................................................ 29
15 Accessories ....................................................................................................................... 30
16 Index................................................................................................................................... 35

Original operating manual - APV Tined Weeder Pro Page 3
CE conformity
according to the EC Machinery Directive 2006/42/EC
We hereby declare that the implement described in the following meets the basic safety requirements in
Annexe I of the EC Machinery Directive 2006/42/EC.
This declaration loses its validity in cases of non-intended use and if changes are made to the implement
that were not approved by the manufacturer.
Manufacturer: APV-Technische Produkte GmbH, HEADQUARTERS,
Dallein 15, A-3753 Hötzelsdorf
Product designation: Tined Weeder Pro VS 600 M1
Number: 07018-1-000
Serial number: All serial numbers of the Tined Weeder Pro VS 600 M1
Product designation: Tined Weeder Pro VS 750 M1
Number: 07019-1-000
Serial number: All serial numbers of the Tined Weeder Pro VS 750 M1
Product designation: Tined Weeder Pro VS 900 M1
Number: 07020-1-000
Serial number: All serial numbers of the Tined Weeder Pro VS 900 M1
Product designation: Tined Weeder Pro VS 1200 M1
Number: 07014-1-000
Serial number: All serial numbers of the Tined Weeder Pro VS 1200 M1
Legal authorised person
for the technical documents: APV-Technische Produkte GmbH, HEADQUARTERS,
Dallein 15, A-3753 Hötzelsdorf
Conformity procedure: Machinery Directive 2006/42/EC Annexe I
Conformity with the following directives:
2006/42/EC Machinery Directive
2004/108/EC EMC Directive
Applicable standards:
EN 349 Safety of machinery – Minimum gaps to avoid crushing of parts of the human body
EN 60204-1 Safety of machinery – Electrical equipment
ISO 12100 Safety of machinery; General principles for design; Risk assessment and risk reduction
ISO 13857 Safety of machinery – Safety distances
ISO 14982 Agricultural and forestry machinery ―Electromagnetic compatibility ―Test methods
and acceptance criteria
Dallein, 01/2020
City, Date
Ing. Jürgen Schöls
Management

Page 4 Original operating manual - APV Tined Weeder Pro
1 Identification of the implement
The Tined Weeder Pro can be clearly identified by the following information on the type plate.
•Designation
•Model
•Production number
Position of the type plate
The type plate can be found on the inside
of the main frame on the left in the
direction of travel, near the connection
point to the top link frame (see Figure 1).
The following image (Figure 2) shows the layout of the type plate:
The data on the type plate have the following
meaning:
No. Meaning
1 Designation
2 Model
3 Production number
4 Weight
5 Year of manufacture
PLEASE NOTE!
In cases of inquiries or warranty claims, please tell us the production number of your
implement.
Figure
1
: Location of the type plate
Figure 2: Layout of the type plate

Original operating manual - APV Tined Weeder Pro Page 5
2 Service
Please contact our service address in the following cases:
•If you still have questions regarding the handling of the Tined Weeder Pro despite the information
provided in this operating manual
•For spare parts orders
•To order maintenance and repair work
Service address:
APV - Technische Produkte GmbH
HEADQUARTERS
Dallein 15
AT-3753 Hötzelsdorf
AUSTRIA
Telephone: [phone]
Fax: [phone]
Email: [e-mail]
Web: www.apv.at
3 Warranty
Please check the implement for any transport damage immediately upon receipt. Later claims regarding
transport damage can no longer be considered.
We provide a six-month factory warranty as of the date of delivery (your invoice or the delivery slip serve
as a warranty certificate).
This warranty is applicable for cases of material or construction faults and does not include parts that are
damaged by normal or excessive wear.
The warranty expires
•if damage is caused by external forces.
•in cases of operating errors.
•if the kW/HP limits are significantly exceeded.
•if the implement is modified, expanded or equipped with third-party spare parts without our
permission.
4 Safety information
This chapter contains general rules of conduct for the intended use of the implement and safety-
related information that should always be observed for your safety.
The list is very extensive, and some of the information does not apply exclusively to the delivered
implement. However, the summary of the information often reminds you of unconsciously neglected safety
regulations for the everyday operation of machines and implements.
4.1 Intended use
The implement is designed solely for normal use in agricultural operations (intended use).
Any other use is considered to be non-intended. The manufacturer is not liable for any resulting damage,
the operator alone bears the associated risk.
Intended use also includes compliance with the conditions for operation, maintenance, and repairs
prescribed by the manufacturer.

Page 6 Original operating manual - APV Tined Weeder Pro
The implement may only be used, maintained and repaired by persons who have relevant experience and
were instructed on the risks. The safety instructions must also be handed over to other users.
The applicable accident prevention regulations as well as the other generally safety-related, occupational
health and road traffic regulations must also be observed.
The manufacturer is not liable for any damage resulting from unauthorised modifications and the use of
components and auxiliary parts.
4.2 General safety-related instructions and accident prevention
regulations
•Check the implement and the tractor for road and operational safety before every use!
•Observe the generally applicable safety and accident prevention regulations!
•The warning and information signs applied to the implement provide important instructions for safe
operation, observe them for the sake of your own safety!
•Observe the respective regulations when using public roads!
•Before starting work, get to know all of the equipment and operating elements as well as their functions.
It is too late to do so during operation!
•The user should wear close-fitting clothing. Avoid wearing loose clothes!
•Keep the implements clean to reduce the risk of fire!
•Check the surrounding area before starting up and operating the implement! (Children!) Ensure
sufficient visibility!
•It is not allowed to carry passengers on the implement during operation and transport!
•The implement must be coupled according to the instructions and only onto the specified devices!
•Special care must be taken when coupling and uncoupling implement to and from the tractor!
•When mounting and dismounting, put the support devices in their respective positions! (Stability)
•Always attach ballast weights at the intended attachment points according to the specifications!
•Observe the permissible axle load, total weight and transport dimensions!
•Transport equipment - e.g. lighting, warning signs and any protective equipment, must be checked and
mounted!
•Never leave the driver's platform while driving!
•The driving behaviour, steering and braking capacity are also affected by mounted or towed
implements and ballast weights. For this reason, always ensure sufficient steering and braking
capacity!
•When driving in curves, take account of the wide radius and/or the centrifugal mass of the implement!
•The implement may only be operated when all of the protective devices are installed and in safety
position!
•It is forbidden to stand in the working area of the implement!
•Do not stand near rotating and swivelling parts of the implement!
•Hydraulic folding frames may only be actuated when nobody is standing in the swivelling range.
•There are pinch and shear points on externally powered (e.g. hydraulic) parts!
•On implements with manual folding, always ensure that the implement is stable!
•For implements that are driven at high speeds with soil-driven tools - Danger after lifting due to the still
rotating centrifugal mass! Only approach the implement when it has come to a standstill!
•Before exiting the tractor, lower the implement onto the ground, switch off the motor and remove the
ignition key!
•Standing between the tractor and the implement is forbidden unless the vehicle is secured against
rolling away using the parking brake and/or with wheel chocks!
•Folded frames and lifting devices must be locked in transport position!
•Packer catch arms must be swivelled in and locked before road transport!
•Lock the track markers in transport position!
•The view on the mounted harrow and the hazardous movement area must be clear (to check the
procedure).
•Cleaning is recommended as specified in the maintenance instructions. The procedure in in
maintenance instruction must be observed and protective equipment must be used.
•Working under the implement is forbidden.

Original operating manual - APV Tined Weeder Pro Page 7
•The implements must be checked regularly by the operator (before every use) for any fractures and
cracks, chafe marks, leaks, loose bolts and connections, vibrations, unusual sounds, and to ensure
they function correctly.
•Hearing protection should be used, if necessary.
•During assembly, the operator must ensure that the requirements for the tractor in terms of the power,
axle loads and weight distribution as specified in the operating manual are met and that the
connections specified in the operating instructions are made correctly.
•When mounting the implement, the operator must ensure that connections to the tractor hydraulic
system are clean and carefully connected.
•When performing the work passes, the tractor's speed must maintained as specified in the operating
instructions. This can be between 4 and 12 km/h.
•Additional lighting (e.g., flashlight) should be used for repair or maintenance work if necessary.
4.3 Mounted implements
•Before mounting and dismounting implements on the three-point linkage, move the operating devices
into the position that excludes unintentional lifting or lowering!
•For three-point mounting, the mounting categories of the tractor and the implement must match or be
adapted!
•There is a risk of injury due to crushing and shearing points in the area of the three-point linkage!
•Do not stand between the tractor and the implement when actuating the external controls for the three-
point mounting!
•When the implement is in transport position, always ensure that the tractor three-point linkage is
sufficiently locked to the sides!
•When driving on roads with the implement lifted, the operating lever must be locked against lowering!
•When mounting the harrow, the operator must ensure that there is a metallic connection made to the
tractor.
•The operator must ensure that no one is standing close to the harrow when it or its components are
being moved by the tractor hydraulic system or when the side wings are being lifted or lowered. The
driver must perform a visual inspection!
•When driving on roads, which is only permitted with the harrow lifted and with folded side wings, the
control block on the hydraulic cylinder prevents lowering of the harrow as well as of the folded up side
wings (additionally secured with a chain). This is also ensured in case of failure of the tractor hydraulic
system.
4.4 Hydraulic system
•The hydraulic system is under high pressure!
•When connecting hydraulic cylinders and motors, the specified connection of the hydraulic hoses must
be observed!
•When connecting the hydraulic hoses to the tractor hydraulic system, make sure that the hydraulic
system on the tractor and implement side is unpressurised!
•For hydraulic function connections between the tractor and the implement, coupling sleeves and
connectors should be marked to rule out operating errors! If the connections are interchanged, the
function will be inverted (e.g. lifting/lowering)! – Danger of accident!
•Inspect the hydraulic hose lines at regular intervals and replace in case of damage or wear! The
replacement lines must comply with the technical requirements of the implement manufacturer!
•Due to the risk of injury, use suitable tools when searching for leaks!
•Liquids escaping under high pressure (hydraulic oil) can penetrate skin and cause serious injuries!
Consult a doctor immediately in case of injury! (Risk of infection!)
•Before working on the hydraulic system, park the implement, depressurize the system and switch off
the motor!
•The securing chains should only be unhooked when they are relieved of tension! (cylinder must be
filled with oil)

Page 8 Original operating manual - APV Tined Weeder Pro
4.5 Maintenance
•Maintenance, repair, and cleaning work as well as the elimination of malfunctions should always be
performed when the drive is switched off and the motor is at a standstill! – Remove the ignition key!
•Check the nuts and bolts regularly for tight fit and retighten if necessary!
•When performing maintenance on the lifted implement, always ensure safety through suitable support
elements!
•When changing work tools with sharp edges, always use suitable tools and gloves!
•Properly dispose of oils, grease and filters!
•Always cut the power supply when working on the electrical system!
•When performing electrical welding work on the tractor and mounted implement, disconnect the cable
on the generator and the battery!
•Spare parts must at least comply with the technical requirements specified by the implement
manufacturer! This is ensured with original parts!
•Cleaning must be performed with water or compressed air. Cleaning must be carried with the
implement lowered, shut down and secured to prevent it being switched on again.
4.6 Tyres
•
When working on the tyres, it must be ensured that the implement is safely parked and secured against
rolling away (wheel chocks).
•
The mounting of wheels and tyres requires sufficient knowledge and proper installation tools.
•
Repair work on the tyres may only be performed by specialists and with suitable installation tools.
•
Check the inflation pressure regularly. Observe the prescribed inflation pressure (4 bar)!
CAUTION!
Misprints, errors and omissions excepted.

Original operating manual - APV Tined Weeder Pro Page 9
5 Safety signs
Pay special attention to the stickers on the implement, as they warn you of
specific dangers!
Read and observe the
operating manual before
operating the implement!
Standing in the danger zone
(swivelling range) is
forbidden!
Caution, risk of crushing!
Lift the implement off the
ground and slowly fold or
unfold.
Do not stand on the
implement while driving!
Loading hooks.
When loading the
implement, attach the ropes
or chains to these points!

Page 10 Original operating manual - APV Tined Weeder Pro
Be careful with escaping
high-pressure liquids!
Observe the instructions in
the operating manual!
Do not stand between the
machines when connecting
the implements and
actuating the hydraulic
system!
Do not climb onto rotating
parts, use the intended
access ladders!
Always switch off the engine
and remove the key before
maintenance work!
Never reach into the
crushing danger zone as
long as the parts can still
move!
After a short period of
operation, re-tighten all bolts
and nuts.

Original operating manual - APV Tined Weeder Pro Page 11
6 Operating instructions for the Tined Weeder Pro
6.1 Mounting on the tractor
Under difficult operating conditions, additional wheel weights can be useful. Please also refer to the
operating manual from the tractor manufacturer.
The tractor should be equipped with sufficient ballast weight at the front to ensure the steering and braking
capacity. At least 20% of the empty vehicle weight is required on the front axle.
The lifting links must be adjusted to the same height on the left and on the right. The implement must be
mounted on the 3-point linkage of the tractor.
Mount the top link so that it slants down towards the tractor during operation. (Observe the specifications
from the tractor manufacturer.)
6.2 Safe parking
1st The parking surface must be suitable for parking the
implement. The ground must be firm and level, so
that the stands do not sink in and the harrow does
not roll away.
2nd To ensure safe parking of the implement, lower the
stands at the rear of the harrow.
3rd Make sure that the tines do not touch the ground in
the process to prevent damage to the tines.
4th The stands must be secured with a spring cotter on
the pin to prevent accidental loosening.
5th The securing chains must be hooked onto the side
frames, and the ball valves on the folding cylinders
must be locked to prevent accidental lowering of the
side frame.
6th Then the hydraulic hoses to the tractor must be
depressurised and uncoupled.
6.3 Folding the Tined Weeder Pro
1st Fold the implement only when it is raised from the ground.
2nd Ensure that no one is standing in the danger area!
3rd Couple the hydraulic line plugs. (Ensure that they are always kept clean!)
4th Afterwards, fill the cylinder with oil (fold together). The cylinders are filled as soon as the load on the
securing chains are relieved.
5. Unhook the securing chains.
6th When folding into transport position, the implement must also be lifted from the ground and the
harrow tines must be folded up (pre-tensioning -3).
7th The feeler wheels on the side frame must be completely raised before the harrow can be folded in
order to maintain the permissible transport width.
8th Hook on the securing chains again after the harrow has been folded.
CAUTION!
The tines may be pre-tensioned only when the Tined Weeder Pro is unfolded.
During the folding procedure, first the outer side frame is folded by 180° onto the inner frame, which is
then folded up by 90°.
The hydraulic connections for folding and tine pre-tensioning are marked with cable ties. If two cable ties
are attached to the hose, it means that it is the flow line (+). In contrast, if only one cable tie is attached to
the hose, it is the return line (-).
Figure 3

Page 12 Original operating manual - APV Tined Weeder Pro
CAUTION!
To achieve a transport width of less than
3 m, the feeler wheels on the first side frame
must be completely moved up in the feeler
wheel bracket.
PLEASE NOTE!
When uncoupling the hydraulic hoses for
the tine pre-tensioning under pressure, first
close the stop tap, and only then unplug the
hydraulic hoses. By doing so, the tines
remain in the desired position, even when
the harrow is parked.
6.4 Working position and setting the working depth
The harrow intensity is set with the pre-tensioning of the spring pack. The
pre-setting is made hydraulically and comfortably from the tractor seat. On
the scale (see Figure 5), the driver can read the level that is currently set.
Here, the springs are not pre-tensioned at positions -3 to 0. Pre-tensioning
begins at 0, and the full pre-tension is reached at position 6. At position -3,
the tines are folded up, which means that the tines are in transport position.
The working speed has a significant effect on the intensity of harrowing. The
normal speed range is between 4 and 12 km/h, depending on the crop
sensitivity and growth stage.
The feeler wheels can be moved on the frame to the desired track width. The
clearance and the tine angle can be adjusted using the pattern of holes in
the feeler wheels. The higher the feeler wheels are moved up in the frame,
the smaller the distance between the frame and the ground and the steeper
the position of the tine ends relative to the ground.
To set all of the feeler wheels, including those at the rear, to the same
height, the same number of holes must be visible above the bracket.
Figure
5
Figure 4: Folding of the Tined Weeder Pro
Figure 6: Working position

Original operating manual - APV Tined Weeder Pro Page 13
PLEASE NOTE!
When the feeler wheels are moved further down, the clearance is increased and the tine
angle becomes steeper, and therefore more aggressive. The tine pressure remains the
same.
PLEASE NOTE!
Ideally, there should almost be a right
angle (90° - 100°) between the wearing
end of the tine and the soil (see Figure 7
- centre). Because of the pre-tensioning,
this angle is only reached while driving.
All of the tine rows should penetrate the soil at the same depth (working depth), i.e. the frame must run
parallel to the ground.
To achieve this, the extension of the top link must also be adjusted. The parallelism of the frame to the
ground can be read on the spirit level on the centre frame, provided that you are on a horizontal plane.
CAUTION!
Only set the harrow with pre-tensioned springs on the ground when the vehicle is already
in motion. If the harrow is set down on the ground too rapidly at a standstill, there can be
damage to the implement.
CAUTION!
When the harrow is lowered, do not allow it to push or roll back with the tractor; otherwise,
the tines and bearing points can be damaged.
CAUTION!
After longer stretches of road transport or standstill, there can be differences in the pre-
tension in the hoses due to a change in temperature of the oil. For this reason, pre-tension
the tines completely and then loosen them again completely two times. Then you can set
the desired pre-tension (e.g. Level 2). This has to be done when the implement is lowered
onto the ground.
CAUTION!
Driving in curves is not permitted. If there is no other option, these curves must be driven
in a very large radius.
Figure 7: An angle of 90° - 100° is ideal

Page 14 Original operating manual - APV Tined Weeder Pro
6.5 Hydraulic tine adjustment
The tines are adjusted with multiple hydraulic cylinders connected in parallel. This allows the tine pre-
tension to be changed while driving.
All of the hydraulic cylinders (Figure 8) are connected by an oil circuit. Adjustments are made using a
double-acting control unit and the flow divider on the centre frame (Figure 9).
6.6 Additional adjustment options for ground adaptation
The slot in the cylinder working point on the side
frame further improves the ground adaptation of the
Tined Weeder Pro. If the laterally bolted, folding
locking plates are installed, the upward ground
adaptation of the side frame is fully available, but the
downward ground adaptation is limited. This has the
advantage that the harrow sags less, which is helpful
when turning. If the plates are removed, the ground
adaptation is fully available in both directions.
Figure 8
Figure 9: Flow divider on the centre frame
Figure 10: Folding locking plate on the side frame

Original operating manual - APV Tined Weeder Pro Page 15
7 Maintenance and care
7.1 General maintenance instructions
To maintain the implement in good condition even after a long service life, the following instructions must
be observed:
•Original parts and accessories are designed especially for the machines or implements.
•Please note that parts and accessories not supplied by us have also not been tested and approved
by us.
•The installation and/or use of such products can therefore possibly negatively change or impede the
constructional properties of your implement. The manufacturer rules out any liability for damages
resulting from the use of non-original parts and accessories.
•The manufacturer is not liable for any unauthorised modifications and the use of components and
mounted parts on the implement.
•All bolted connections should be re-tightened at the latest after 3 operating hours and again after 20
hours, and then checked regularly. Loose bolts can cause significant consequential damage, which
is not covered by the warranty.
•The grease points on the joints and bearings must be lubricated regularly (approx. every 10 operating
hours with universal grease).
•After the first 10 operating hours and subsequently every 50 operating hours, the hydraulic units and
tube lines must be checked for leaks and the bolted connections must be tightened if necessary.
•Check the hydraulic hoses for wear before every operation.
•Caution! Liquids escaping under high pressure can penetrate the skin. For this reason, a physician
must be consulted immediately in case of accident!
•After cleaning, lubricate all of the grease points and distribute the grease evenly in the bearing points
(e.g. perform a short test run).
•Do not use a high pressure cleaner to clean bearing and hydraulic parts.
•The paint can be damaged by cleaning with excessive pressure.
•During the winter, the implement should be protected against rust with an environmentally-friendly
product.
•Park the implement protected from weather conditions.
•Hydraulically as well as mechanically folded implement must only be parked in a folded state.
•Put down the implement in a way that the tines are not needlessly strained.
•Occasionally check the tyre inflation pressure (4 bar).
PLEASE NOTE!
When the implement is lifted off of the ground, the two side wings of the frame should be
pointing slightly down. If this is not the case or if the wings are pointing down too much,
the stop bolts on the joint must be adjusted.

Page 16 Original operating manual - APV Tined Weeder Pro
7.2 Tine change
To change broken or worn tines:
1. Loosen the nut (1) on the plastic piece (2).
2. Pull the bearing unit (bolt + nut + bearing shell)
and the tines out of the frame.
3. Reverse procedure for assembly.
4. The recommended tightening torque for the nut
is of 3 Nm. Ensure that the nut is not tightened
too much, so that the tine can fall downward
with its net weight. If this is not the case, the
tine cannot work properly when the pre-tension
is low.
7.3 Changing the springs
Overview: Diagram of the spring attachment
Figure 12: Diagram of the spring attachment
1
Plastic shell
2
Snap-fit
3
Fastening bolt
Figure 11: 1 = nut, 2 = plastic piece

Original operating manual - APV Tined Weeder Pro Page 17
1. Step
Unlock the snap-fits on one side of the spring assembly. To do so, press from the side in the hole
in the spring assembly with a bolt or a pin (8 mm diameter) – as shown in Figure 13 – until the pins
touch. As a result, the snap-fits on one side are pressed open.
2. Step
Push the pin out of the spring assembly. To do so, press with a bolt or a pin (8 mm diameter) into
the hole in the spring assembly on the opposite side. Now all of the pins can be pulled out of the
spring assembly, and the entire spring assembly is released from the frame.
3. Step
To install the new spring assembly, it must first be put in position.
Then the fastening bolt is pressed into the hole in the spring assembly as shown in Figure 15.
Ensure that all of the snap-fits are locked again. This is the case when the fastening bolt is pressed
far enough into the hole. It may be necessary to press it in further using a bolt or a pin (8 mm
diameter).
Figure 13: Step 1
Figure 14: Step 2

Page 18 Original operating manual - APV Tined Weeder Pro
7.4 Repairs and service
In case of failure or damage to the Tined Weeder Pro, please contact the manufacturer. The contact data
can be found in chapter 2 Service.
8 Information on nature conservation and environmental
protection
Reduction of noise pollution during use
Any loose parts (e.g. chains) should be attached to prevent unnecessary noise.
Energy-efficient use
The tines of the Tined Weeder Pro should not penetrate into the field deeper than necessary. By doing so,
the towing vehicle is not unnecessarily strained and fuel can be saved.
Recyclable raw materials during disposal
Many parts of the Tined Weeder Pro are made of steel or spring steel (such as the centre frame, side
frame, tine section, tines, ...) and can be accepted and recycled by a waste disposal plant.
Figure 15: Step 3

Original operating manual - APV Tined Weeder Pro Page 19
9 Technical data
Type designation: VS 600 M1 VS 750 M1 VS 900 M1 VS 1200 M1
Mode of operation:
With its unique tine spring system, the Tined Weeder Pro is a crop
cultivation implement that adapts precisely to the ground. The harrow
tines can be lifted and are pivot-mounted, so that the harrow can only
deflect up and down, not to the left and right.
Working width: 6.2 m 7.6 m 9.2 m 12.2 m
Transport dimensions,
folded (L x W x H in m):
2.40 x 3.00 x
2.85
2.40 x 3.00 x
3.55
2.40 x 3.00 x
3.55
2.40 x 3.00 x
3.55
Working depth: All models: 0-30 mm (depending on the soil conditions)
Number of tines: 178 tines 218 tines 264 tines 350 tines
Tine diameter: All models: 8 mm
Tine length: All models: 520 mm
Line distance: All models: 35 mm
Mounting/hitch (three-
point, …): Mounting – CAT 2 / CAT 2N
Feeler wheels 4 tines 4 tines 4 tines 6 tines
Net weight: 800 kg 900 kg 1100 kg 1500 kg
Parking supports: All models: 2 supports, if no feeler wheels are used at the rear
Working tools: Cranced tines with a diameter of 8 mm
Ground adaptation: Is achieved through the unique tine spring system
Minimum tractor
performance: 37 kW / 50 HP 44 kW / 60 HP 55 kW / 75 HP 66 kW / 90 HP
Accessories:
(see page 3030)
•
Mounting option for PS120 M1 – PS500 M2
•Warning sign with lighting
•Platform kit for the PS series
•Dispersion plate installation
•Rear feeler wheels
•Operating hours counter
•Top link sensor
•Wheel sensor
•GPSa sensor
•Carbide tines
•Manual tine lifting
Can be equipped with: PS 120 M1 – PS 500 M2 (see Point 9.2)

Page 20 Original operating manual - APV Tined Weeder Pro
9.1 Harrow array widths
VS600: VS750:
Figure 16: VS 600 Figure 17: VS 750
VS900:
Figure 18: VS 900
VS1200:
Figure 19: VS 1200