ARAG IBX100 4679004 Installation and operating instructions

INSTALLATION, USE AND MAINTENANCE
4679002
IBX100 ELECTRONIC CONTROL UNIT
Object Pool rel. 1.2.0

2
• LEGEND OF SYMBOLS
=Generic danger
=Warning
ECU =IBX100 remote control unit
OP =Object Pool
TC =Task Controller
This manual is an integral part of the equipment to which it refers and must accompany the equipment in case of sale or change of ownership. Keep it for any
future reference; ARAG reserves the right to modify product specications and instructions at any moment and without notice.
WARNING:
THE NATIVE CONTROLS INSIDE YOUR VIRTUAL
TERMINAL HAVE THE PRIORITY ON ALL THE CONTROLS
DERIVING FROM THE IBX100. PLEASE, KEEP THIS IN
MIND WHEN PROGRAMMING AND USING THE PRODUCT.
LEGEND OF SYMBOLS

3
CONTENTS
1 Risks and protections before assembly.................................4
2 Intended use .............................................................................4
3 Precautions ...............................................................................4
4 Package content .......................................................................4
5 Position on farming machine ..................................................5
5.1 System recommended composition.................................5
5.2 Control unit fixing .............................................................6
6 Wiring connections ..................................................................7
6.1 General precautions for a correct harness position .........7
6.2 Control unit (ECU) connection .........................................7
6.3 Connection of proportional hydraulic valves ....................8
6.4 Sensor connection...........................................................8
7 ISOBUS system cable connection ..........................................9
7.1 Connection of in-cab cable ..............................................9
7.2 Connection of ISOBUS cable...........................................9
8 “OBJECT POOL” loading .......................................................10
9 Control layout .........................................................................11
10 HOME.......................................................................................12
11 Data and Settings ...................................................................12
12 Implement settings.................................................................13
12.1 Basic settings.................................................................13
12.2 Tank ...............................................................................14
12.3 Belt.................................................................................14
12.4 Spinner ..........................................................................14
12.5 Speed ............................................................................15
12.6 System configuration .....................................................15
12.7 Calibration......................................................................16
12.8 Geometry.......................................................................16
13 Manage presets ......................................................................17
13.1 Calibration parameters...................................................18
13.1.1 Factor estimation.............................................................. 18
13.1.2 Weight comparison .......................................................... 19
13.1.3 Calibration procedure ...................................................... 20
13.2 Preset totals - Preset averages ......................................22
14 Working parameters ...............................................................23
15 Alarms .....................................................................................24
16 JOB DATA ................................................................................25
17 Capacity...................................................................................26
18 Status.......................................................................................27
18.1 Device status .................................................................27
18.2 ISOBUS .........................................................................28
18.2.1Auxiliary commands......................................................... 28
18.3 Test controllers...............................................................29
18.4 System settings..............................................................29
18.5 Registration....................................................................29
19 user preferences.....................................................................30
20 USE ..........................................................................................31
20.1 Alarms ...........................................................................31
21 Auto..........................................................................................32
21.1 Rate ...............................................................................32
21.2 Spinner speed................................................................33
21.3 Speed simulation ...........................................................33
22 Tank .........................................................................................34
22.1 Reset of tank content.....................................................34
22.2 Filled quantity manual setup..........................................35
22.3 Manual setting of tank content .......................................35
22.4 Tank filling ......................................................................35
23 Change target .........................................................................36
24 Main control ON/ OFF.............................................................37
24.1 Controls WITH Auxiliary Input ........................................37
24.2 Controls WITHOUT Auxiliary Input.................................37
25 Maintenance / diagnostics / repairs......................................38
25.1 Cleaning rules................................................................38
25.2 LED status key...............................................................38
25.3 Error messages .............................................................39
25.4 Troubleshooting..............................................................40
26 Technical data.........................................................................41
27 End-of-life disposal ................................................................41
28 Guarantee terms .....................................................................41
29 EU declaration of conformity.................................................41

4
FOREWORD
• MANUAL USE MODES
The section of this manual dedicated to the installation contains information for installers. For this reason we have used technical terms without
providing explanations which would be necessary for end users only.
THE INSTALLATION MUST BE CARRIED OUT BY AUTHORIZED AND SKILLED PERSONNEL ONLY. ARAG IS NOT RESPONSIBLE
FOR ANY OPERATION SPECIFIED IN THIS MANUAL CARRIED OUT BY UNAUTHORIZED OR UNSKILLED PERSONNEL.
• LIMITATIONS
The descriptions of the assembly phases refer to a "general" Virtual Terminal, so specic models will not be mentioned, unless a certain installation
procedure concerns exclusively one Virtual Terminal type.
• RESPONSIBILITY
The installer must carry out "workmanlike" installations and ensure to the end user the perfect operation of the whole system both with ARAG
components only and other brands' components.
ARAG always recommends using its components to install control systems.
The installer will be held responsible for any malfunction if he decides to use other brands' components even without actually changing the system
parts or harness.
The compatibility check with components and accessories of other manufacturers shall be carried out by the installer.
If the ARAG components installed together with other brands' components get damaged because of what stated above, no direct or indirect warranty
will be provided.
1 RISKS AND PROTECTIONS BEFORE ASSEMBLY
Installation works, except the main connection (ISOBUS system, Chap. 7) must be done with battery disconnected, using suitable
tools and any personal protective equipment deemed necessary.
Use ONLY clean water for treatment tests and simulations: using chemicals during simulated treatment runs can seriously injure
persons in the vicinity.
2 INTENDED USE
The apparatus you have purchased is a standard ISOBUS system compliant with ISO11783 to be applied to a granular fertilizer spreader machine
with belt conveyor.
This device is designed to work on agricultural machinery for granular fertilizer spreading with belt conveyor.
The machine is designed and built in compliance with ISO 14982 standard (Electromagnetic compatibility - Forestry and farming
machines), harmonized with 2014/30/EU Directive.
3 PRECAUTIONS
• Do not aim water jets at the equipment.
• Do not use solvents or fuel to clean the case outer surface.
• Do not clean equipment with direct water jets.
• Comply with the specied power voltage (12 VDC).
• In case of voltaic arc welding, remove connectors from the device and disconnect the power cables.
• Only use ARAG genuine spare parts and accessories.
4 PACKAGE CONTENT
Fi g . 1
Control unit
Harnesses must be ordered separately (Ref. ARAG general catalog).

5
INSTALLATION
5 POSITION ON FARMING MACHINE
5.1 System recommended composition
WARNING: DO NOT CONNECT ISOBUS CONNECTOR (chap. 7 on page 9).
THIS CONNECTION MUST BE CARRIED OUT LATER, ONLY AFTER INSTALLING ALL THE COMPONENTS.
To connect all parts of the system correctly, make sure to use the proper connection cables.
Consider any variants depending on system type.
ISOBUS
PLUG
VIRTUAL
TERMINAL
AUXILIARY
INPUTPLUG
24 5
1
10 m
3 m
1 m 0,2 m
3 3
5 m
5 m
GS
BS
SL SR
SPINNERLEFTSPINNERRIGHT
2
2
2
2
Legend of connection cables:
1Standard ISOBUS connector (ISOBUS PLUG)
2Sensors
3Proportional hydraulic valves
4Auxiliary ISOBUS Input
5ISOBUS Explorer Joystick
GS Speed sensor / Gate
BS RPM sensor / Spreading belt
SL RPM sensor / Left spreading spinner
SR RPM sensor / Right spreading spinner
Fi g . 2

6
INSTALLATION
5.2 Control unit xing
Fix the control unit in a visible position within easy reach as shown in the gure.
IBX100
Fi g . 3
Consider all necessary connections of the device (par. "Wiring harness connection"), the cable length, and make sure there is enough
space for connectors and cables.
For any reference to the system conguration read par. 5.1.
Respect the mounting direction of the control units, as specied in Fi g . 4 (connectors shall be facing down).
Fix the ECU using the 4 bolts tted into their slots (A, Fi g . 4 ).
No other type of assembly is allowed.
Fi g . 4
WIRING HARNESS CONNECTION OVERALL DIMENSIONS
No. OF CONNECTION POINTS
1Proportional hydraulic valves + Sensors
2Standard ISOBUS connector
(ISOBUS PLUG)
Fi g . 5 Unit of measurement: mm
Fi g . 6

7
INSTALLATION
6 WIRING CONNECTIONS
• Use original ARAG harnesses only.
• Take care not to break, pull, tear or cut the cables.
• Use of unsuitable cables not provided by ARAG automatically voids the warranty.
• ARAG is not liable for any damage to the equipment, persons or animals caused by failure to observe the above instructions.
6.1 General precautions for a correct harness position
• Securing the cables:
- secure the harness so that it does not interfere with moving parts;
- route the harnesses so that they cannot be damaged or broken by machine movements or twisting.
• Routing the cables to protect against water inltrations:
- the cable branches must ALWAYS be face down (Fi g . 7).
Fi g . 7
Fi g . 8
• Fitting the cables to the connection points:
- Do not force the connectors by pushing too hard or bending them: the contacts may be damaged and system operation may be compromised.
Use ONLY the cables and accessories indicated in the catalog, having technical features suitable for the use to be made of them.
6.2 Control unit (ECU) connection
WARNING: DO NOT CONNECT ISOBUS CONNECTOR (chap. 7 on page 9).
THIS CONNECTION MUST BE CARRIED OUT LATER, ONLY AFTER INSTALLING ALL THE COMPONENTS.
Connect harnesses as specied in par. "Wiring harness connection" ; each one of them shall be connected to the corresponding socket on the remote control unit.
Close the unused connectors with the relevant caps supplied in the package.
If they prove hard to insert, do not force them, but check the shown position.
Fi g . 9
Some connectors are supplied with separated slide.
Manually insert the slide in the most convenient position for connector insertion and removal.
• Open connector slide (1,Fi g . 9 ).
• To position connector (2), insert it inside socket (3), then press: during this operation, take care not to bend the electric contacts.
• Close slide (4) until it locks in place.

8
INSTALLATION
6.3 Connection of proportional hydraulic valves
Fi g . 10
The system is able to control one belt and two spreading spinners through proportional valves.
Fix the connectors to the relevant valve according to the initials indicated in your assembly general diagram (par. 5.1).
• Position seal (1) onto connector (2), then connect the latter pressing it fully home (3):
during this operation, take special care not to bend valve electric contacts.
• Insert screw inside connector, and screw it (4) until it is tightened.
The function of each switch on the hydraulic function control panel is described below.
• Connect connectors to the valve as shown in the table:
CONTROL MOVEMENT CONNECTOR
SPREADING BELT On BH
Off BH
SPREADING SPINNERS On SH
Off SH
6.4 Sensor connection
Fix the connectors to the relevant functions according to the initials indicated in your assembly general diagram (par. 5.1).
Harness cables are marked with a symbol denoting their functions: please see the table for correct harness connection.
Use ARAG sensors: use of unsuitable sensors not provided by ARAG automatically voids the warranty.
ARAG is not liable for damage to the equipment, persons or animals caused by failure to observe the above instructions.
ITEM CONNECTION
GS Speed sensor
BS RPM sensor / Spreading belt
SL RPM sensor / Left spreading spinner
SR RPM sensor / Right spreading spinner
- The products are supplied with the sensor installation instructions.
The following speed sensors can also be used as RPM sensors:
• inductive speed sensor (code 467100.086);
• magnetic speed sensor (code 467100.100).
All ARAG sensors use the same type of connector. Connect the sensor connector to the relevant harness; make sure it is correctly tted and push it
until locking it.
Fi g . 11 Fi g . 1 2

9
INSTALLATION
7 ISOBUS SYSTEM CABLE CONNECTION
After carrying out all the system connections, as described in the previous pages:
- Connect the ISOBUS PLUG and IN-CAB connectors.
- Switch on the Virtual Terminal.
- Wait for the OP complete loading (chap. 8).
IN-CAB
CONNECTION
ISOBUS
PLUG
Fi g . 1 3
7.1 Connection of in-cab cable
Use the cable supplied in the auxiliary input package:
ARAG Auxiliary Input control system is not compulsory on all systems, and must thus be ordered separately.
Some Virtual Terminals allow controlling spreading spinners and gate directly from monitor touch-screen panel.
7.2 Connection of ISOBUS cable
Use cable 1 (Fi g . 2 , par. 5.1 System recommended composition).
Connections: x the connectors (ISOBUS connection in Fi g . 13 ); make sure they are correctly tted and push until locking them.

10
OBJECT POOL LOADING
8 “OBJECT POOL” LOADING
Images and the relevant description texts contained in this manual are given as a reference as they can vary depending on the
Virtual Terminal used. If the descriptions do not correspond to the text displayed in your Virtual Terminal, refer to the manual
attached to the latter.
Press to display the OP selection
page of the ECU.
Press to enter the main screen.
Wait for the ECU OP to be fully
loaded.

11
USING THE KEYS
9 CONTROL LAYOUT
Fi g . 14
Goes back to main screen
Goes back to previous menu, or scrolls the pages of a menu (previous page)
Scrolls the pages of a menu (next page)
Saves the changes to current page
Fig. 15
Quits without conrming the changes
Saves the changes
ENTERING A NUMERICAL VALUE
Fig. 16
Deletes
Exits
Conrms
Fi g . 1 7
Read-only value or previously set in another menu.

12
HOME
10 HOME
MENU SELECTION BUTTONS
Data and Settings
Alarms
AUTO
Tank
Change target
Main control ON/OFF
Fig. 18
11 DATA AND SETTINGS
Fig. 19
Data and Settings
Allows setting all the Data and Settings items.
Before settting Data and Settings check:
• that all components are correctly installed;
• the correct connection to the power source;
Failure to correctly connect system components or to use specied components might damage the device or its components.
Upon rst switching on, enter the device basic settings
AT THE END OF THE DESIRED SETTINGS IT IS NECESSARY TO SAVE PAGE CHANGES USING BUTTON OTHERWISE THE
CONFIGURATION IS LOST.

13
IMPLEMENT SETTINGS
12 IMPLEMENT SETTINGS
1
Fig. 20 1 - 2 Congure farming machine settings.
2
Fig. 21
12.1 Basic settings
Allows conguring:
1 / 3
Belt actuator: type of device used to control spreading belts.
- Motorized valve: system with electric-activated valves - with gearmotor.
- PWM valve: system with solenoid valves.
2
/
3
Spinner sensing: number of sensors used to detect spreading spinner operation.
-
NO sensor
- 1 sensor
- 2 sensors
3
/
3
Spinner actuator: type of device used to control spreading spinners.
- Mechanical: spreading spinners are controlled through the farming machine.
- Motorized valve: system with electric-activated valves - with gearmotor.
- PWM valve: system with solenoid valves.

14
IMPLEMENT SETTINGS
12.2 Tank
Allows setting the tank data:
1 / 1
Tank settings:
- Reserve: indicate the reserve value under which the alarm is triggered
- Capacity: indicate the tank capacity.
12.3 Belt
Allows setting the spreading belt data:
1 / 3
Belt settings:
- Sensor constant: indicate the constant of the sensor installed on spreading belt roller. The value must be provided by the sensor manufacturer.
- Belt minimum speed: indicate the minimum spreading belt speed under which the alarm is triggered.
- Belt maximum speed: indicate the maximum spreading belt speed beyond which the alarm is triggered.
- Gate width: indicate the distribution gate width.
- Belt roller diameter: indicate the spreading belt roller diameter.
2 / 3
Belt alarms/display:
Alarms:
- Rate error: indicate rate tolerance percentage beyond which the alarm is triggered.
Display:
- Rate display cut-off: indicate the rate display tolerance percentage beyond which the alarm is triggered and the system displays the actual rate
value. Within the set percentage, the system continues displaying the preset rate even if different from the actual one.
3 / 3
Controller settings:
Belt:
- Valve: displays the type of device used to control spreading belts (“12.1 Basic settings" on page 13).
- Aggressiveness: adjusts the energy used by the valve to control the belt. Decreases aggressiveness. / Increases aggressiveness.
The ideal adjustment is obtained when belt movement is smooth.
12.4 Spinner
Allows setting the spreading spinners data:
1 / 2
Spinner settings:
- Mode: displays the type of spreading spinner control (“12.1 Basic settings" on page 13).
- Sensors number: displays the number of sensors for spreading spinner control (“12.1 Basic settings" on page 13).
- Sensor 1 constant: indicate the constant of spreading spinner sensors. The value must be provided by the sensor manufacturer.
- Sensor 2 constant: indicate the constant of spreading spinner sensors. The value must be provided by the sensor manufacturer.
- Display cut-off: indicate the spreading spinner speed display tolerance percentage beyond which the alarm is triggered and the system displays the
actual speed value. Within the set percentage, the system continues displaying the preset speed even if different from the actual one.
•
Disabled: function NOT enabled.
• 3%: 3% tolerance
• 5%: 5% tolerance
• Rate error: threshold of Spinner alarms settings Relative mode.
- Spinner max speed: enter the maximum RPM value of spreading spinner sensor.
- Link Spinner to "Main" sw.: enables or disables activation or
deactivation of spreading spinners through the control on switch box:
ON / OFF
- Spinner switch-OFF: enter the number of seconds between spreading spinner deactivation and actual spinner block.
2 / 2
Spinner alarms:
- Mode: displays the type of spreading spinner control (“12.1 Basic settings" on page 13).
• Disabled: function NOT enabled.
• Absolute: enter minimum and maximum speed values of spreading spinners. All the values outside the set range will trigger the alarm.
• Relative: enter the percentage value beyond which spreading spinner alarm is triggered.

15
IMPLEMENT SETTINGS
12.5 Speed
Allows setting the speed data:
1 / 1
Speed settings:
- Source: allows to select the source for speed calculation.
• Wheel sensor (ECU): when this option is enabled, speed is calculated through the pulses coming from the speed sensor, installed on the wheel
and connected to the ECU through proper harness. The wheel constant must be set in the following item.
• Tractor wheel:when this option is enabled, speed is calculated through the pulses coming from the speed sensor, installed on the wheel and
directly connected to the Virtual Terminal. The wheel constant must be set in the following item.
• Tractor radar: information concerning speed is received by the GPS, which is connected directly to the system.
• Simulated speed: Allows to enable speed simulation in order to carry out adjustment tests even when the machine is stationary.
- Wheel sensor constant: enter the wheel constant value calculated with the suitable formula:
The wheel constant can be calculated with a good approximation by detecting the distance traveled by the wheel with the speed sensor.
The longer the distance traveled, the more accurate the wheel constant calculation.
Kwheel = distance traveled (cm)
no. of detection points x wheel rpm
<distance traveled> distance expressed in cm covered by the wheel along measurement travel.
<no. of measurement points> number of measurement points (e.g., magnets, bolts, etc.), mounted on wheel.
<no. of wheel revolutions> number of wheel revolutions required to travel measurement distance.
Take measurements with tires at the operating pressure. This test must be performed on medium-hard terrain; for application to very soft or very hard
terrain, rolling diameter may vary, leading to inaccurate output calculation; when this is the case, repeat the procedure. During the test, cover the
distance with the tank lled up to half capacity with water.
- Simulated speed: enter the simulated speed value.
12.6 System configuration
Allows setting the system data:
1 / 3
Spreading:
- Rate control: Selects automatic activation or manual activation of rate control.
- Spinner control: Selects automatic activation or manual activation of spreading spinner control.
Menu item visible only ifSpinner actuator selected is Motorized valve or PWM valve.
2 / 3
Auxiliary commands: select the type of auxiliary control (Auxiliary Input) connected to the system.
• ARAG Direct Switches
• ARAG joystick
• User Direct Switches
• User joystick
- Auxiliary enable: enable / disable the auxiliary control (Auxiliary Input)
- Main switch: enable / disable the control that activates the gate.
- Belt/Spinner ON/OFF: enable / disable the control that activates or deactivates the spreading belt and spinners.
- Rate/Spinner speed: enable / disable the control of spreading spinner output and speed.
- AUTO/MANUAL: enable / disable the automatic or manual controls of spreading belt and spinners
3 / 3
Task controller: functions: some functions carried out by the system through the Task Controller can be performed ONLY if enabled in this menu.
- Job totals: enable / disable the job total counter control.
- Section control: enable / disable automatic deactivation of spreading spinners.
- Variable application: enable / disable the use of prescription maps for treatments with variable application.
Task controller: timings: allows managing valve timings depending on the system connected.
- Section switch-ON: indicate the time between the moment when the command is sent to the valves and the actual moment in which product output starts.
- Section switch-OFF: indicate the time between the moment when the command is sent to the valves and the actual moment in which product output stops.
- Rate setpoint latency: adjustment parameter for variable applications (with the use of prescription maps): this datum is used to indicate the advance time of application
rate adjustment when the machine approaches the area changeover of the prescription map.

16
12.7 Calibration
Allows setting the calibration data:
1 / 1
Calibration settings:
- Mode: selects the type of control to carry out calibration.
• Belt speed control: during calibration the system tries to keep the speed target set constant.
• Rate control during calibration the system tries to keep the rate target set constant.
- Accumulation time: enter the value that indicates the belt actuation time in full operational mode.
- Settling time: enter the value that indicates the belt stopping time.
- Minimum belt pulses: enter the value indicating the minimum number of pulses to start calibration of spreading belt roller.
- Simulated speed: enter the value indicating the simulated speed during calibration.
- Belt speed: enter the value indicating the spreading belt speed during calibration.
- Spinner speed: enter the value indicating the spreading spinner speed during calibration.
12.8 Geometry
Allows setting the equipment data:
Check Virtual Terminal settings: if a specic menu is available (varying based on your system) to program machine geometry, it has the priority over the ECU
menu.
1 / 1
Geometry settings:
- Hitch point: select the type of equipment connection.
- Distance Hitch-Axle:
m
3,500
Fig. 22
- Distance Hitch-Spinners:
m
4,000
Fig. 23
- Spreading distance:
m
5,000
Fig. 24
- Spinners lateral posit.:
difference between the equipment
central axis and the central point of
spreading spinners axis.
m
0,500
Fig. 25
IMPLEMENT SETTINGS

17
13 MANAGE PRESETS
Fig. 26
This menu allows:
- Setting 8 different treatment congurations: Preset.
- Activating one conguration among the preset ones.
- Consult job data of the treatment selected: Preset.
Number
of job
Name
of job
Rate
Fig. 27
Allows selecting and activating the Presets and setting them.
Preset active.
Preset not active.
1
2
3
4
5
6
Fig. 28
Features to set for each Preset:
1Type in the job name.
2Enter the Rate value.
3Enter the Spreading width value.
4Enter the Spinner speed value.
5Enter the density value suitable for Working density treatment start moment.
6 Displays the percentage value of the difference between Working density 5and
Density (“Fig. 29" on page 18).
MANAGE PRESETS

18
13.1 Calibration parameters
1
2
3
4
Fig. 29
Features of the selected Preset:
1Activates or deactivates Density value entry.
2Enter the product density value suitable for calibration start moment. THE VALUE
COULD BE DIFFERENT FROM THE NOMINAL VALUE
3Enter the Calibration factor value.
4Allows selecting Calibration methods if the current Calibration factor must be
updated.
1
2
3
Fig. 30
Allows selecting the calibration method to calculate the Calibration factor value.
1 estimation of the constant through the geometrical data of system conguration (par.
13.1.1).
2 comparison between weight own out of the tank and weight calculated by the application
(par. 13.1.2).
3 automatic calibration procedure:
comparison between revolutions made by the roller (spreading belt) and weight
own out of the tank (par. 13.1.3).
13.1.1 Factor estimation
1
2
4
3
5
Fig. 31
1Preset datum ("Fig. 29").
2Preset data (“12.3 Belt" on page 14)
3Enter the Gate height value, the system will calculate the “New” factor.
4Displays the new calibration constant value calculated by the system.
5Press Apply "new" factor value to apply the value and conrm the calibration.
MANAGE PRESETS

19
13.1.2 Weight comparison
WARNING: before starting the procedure, make sure that the spreading system is off (position OFF).
The spreading belt and spinners must NOT be in motion.
- Insert the material in the tank.
- Activate the spreading system.
WARNING:
The material starts owing out.
- Stop the system before full tank emptying.
- Weigh the quantity of product own out of the tank and enter the Applied product value 3.
- The system calculates the new calibration constant value “New” factor.
- Press Apply "New" factor value to apply the value and conrm the calibration.
The more product ows out of the tank the more accurate will calibration be.
3
2
4
5
1
Fig. 32
1Preset datum (“Fig. 29" on page 18).
2Weight of the applied product, calculated by the application.
3Quantity of product own out of the tank during calibration.
4Displays the new calibration constant value calculated by the system.
5Applies the calibration value.
MANAGE PRESETS

20
13.1.3 Calibration procedure
WARNING: before starting the procedure, make sure that the spreading system is off (position OFF).
The spreading belt and spinners must NOT be in motion.
- Insert the material in the tank.
- Check that the simulated speed is enabled and select the type of control to carry out the calibration (“12.7 Calibration" on page 16).
2
1
Fig. 33
1Displays the current phase of calibration procedure.
2Press START button to start calibration.
WARNING:
The material starts owing out.
3
4
5
6
Fig. 34
3The system activates the spreading belt roller and the material ows out of the tank.
4Number of pulses detected by the sensor on the spreading belt.
5 - 6 Speed detected by the spreading belt roller.
Depending on the type of calibration control selected (“12.7 Calibration" on page 16):
- Mode: Belt speed control:the system tries to keep the speed target set constant.
- Mode: Rate control the system tries to keep the rate target set constant.
7
Fig. 35
7 End the calibration by pressing STOP before the full tank emptying.
If the device signals a calibration error, check that conguration parameters are
correctly set (“12.7 Calibration" on page 16).
MANAGE PRESETS