Arbor Technology EasyBoard-882E User manual

1
EasyBoard-882E
User’s Manual
Version 1.2
Wide Range Temperature
3.5” Compact Board
85
2014.05
85

- 2 -
This page is intentionally left blank.

- i -
Revision History
Version Release Time Description
1.0 September 2013 Initial release
1.1 March 2014 P.3 Spec 4GB-->8GB
P.6 Change Dimension
P.8 Change Jumper Board Top
P.10,11 Correct JPWR1
& JBAT1 location
P.19 Revise USB 2,3
P.21 Revise COM2
1.2May 2014 P.10 Change JPWR1
Jumper default to ATX mode

- ii -
This page is intentionally left blank.

- iii -
Contents
Table of Contents
Revision History .................................................................................i
Table of Contents .............................................................................iii
Preface................................................................................................v
Copyright Notice ..................................................................................... v
Declaration of Conformity ....................................................................... v
CE.................................................................................................... v
FCC Class A ................................................................................... vi
RoHS .............................................................................................. vi
SVHC / REACH ..............................................................................vii
Warning..................................................................................................vii
Replacing Lithium Battery ......................................................................vii
Technical Support ..................................................................................vii
Warranty................................................................................................viii
Chapter 1 - Introduction....................................................................1
1.1. The Product .....................................................................................2
1.2. About this Manual ............................................................................ 2
1.3. Specications...................................................................................3
1.4. Inside the Package ..........................................................................4
1.5. Ordering Information ........................................................................ 4
Chapter 2 - Getting Started...............................................................5
2.1. Board Dimensions............................................................................6
2.2. Block Diagram..................................................................................7
2.3. Jumpers & Connectors ....................................................................8
2.3.1. Layout .................................................................................... 8
2.3.2. Jumpers ............................................................................... 10
2.3.3. Connectors .......................................................................... 15
2.4. Driver Installation Notes.................................................................36
Chapter 3 - BIOS..............................................................................39
3.1. Main ............................................................................................... 41
3.2. Advanced ....................................................................................... 42
3.2.1. ACPI Settings.......................................................................43
3.2.2. S5 RTC Wake Settings ........................................................ 44
3.2.3. CPU Conguration...............................................................46
3.2.4. SATA Conguration.............................................................. 48
3.2.5. AMT Conguration ............................................................... 51
3.2.6. USB Conguration ............................................................... 53
3.2.7. Super IO Conguration ........................................................ 54
3.2.8. Hardware Monitor ................................................................56
3.2.9. CPU PPM Conguration ...................................................... 57

- iv -
Contents
3.3. Chipset...........................................................................................58
3.3.1. PCH IO Conguration .......................................................... 59
3.3.2. System Agent (SA) Conguration ........................................ 63
3.4. Boot................................................................................................69
3.5. Security .......................................................................................... 71
3.6. Save & Exit ....................................................................................72
Appendices ......................................................................................75
Appendix A. AMI BIOS Checkpoints ..................................................... 76
A.1. Bootblock Initialization Code Checkpoints .............................76
A.2. Bootblock Recovery Code Checkpoints ................................. 78
A.3. POST Code Checkpoints ....................................................... 79
A.4. DIM Code Checkpoints ..........................................................82
A.5. ACPI Runtime Checkpoints ....................................................83
Appendix B. I/O Port Address Map ...................................................... 84
Appendix C. Interrupt Request Lines (IRQ) ..........................................87
Appendix D. BIOS Memory Map...........................................................92
Appendix E. Direct Memory Access......................................................93
Appendix F. Watchdog Timer (WDT) Setting ........................................94

- v -
Preface
Preface
Copyright Notice
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of the
manufacturer.
Declaration of Conformity
CE
The CE symbol on your product indicates that it is in compliance with the
directives of the Union European (EU). A Certicate of Compliance is available
by contacting Technical Support.
This product has passed the CE test for environmental specications when
shielded cables are used for external wiring. We recommend the use of shielded
cables. This kind of cable is available from ARBOR. Please contact your local
supplier for ordering information.
This product has passed the CE test for environmental specications. Test
conditions for passing included the equipment being operated within an
industrial enclosure. In order to protect the product from being damaged by ESD
(Electrostatic Discharge) and EMI leakage, we strongly recommend the use of
CE-compliant industrial enclosure products.
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

- vi -
Preface
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
RoHS
ARBOR Technology Corp. certies that all components in its products are
in compliance and conform to the European Union’s Restriction of Use of
Hazardous Substances in Electrical and Electronic Equipment (RoHS) Directive
2002/95/EC.
The above mentioned directive was published on 2/13/2003. The main purpose
of the directive is to prohibit the use of lead, mercury, cadmium, hexavalent
chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl
ethers (PBDE) in electrical and electronic products. Member states of the EU
are to enforce by 7/1/2006.
ARBOR Technology Corp. hereby states that the listed products do not contain
unintentional additions of lead, mercury, hex chrome, PBB or PBDB that exceed
a maximum concentration value of 0.1% by weight or for cadmium exceed
0.01% by weight, per homogenous material. Homogenous material is dened as
a substance or mixture of substances with uniform composition (such as solders,
resins, plating, etc.). Lead-free solder is used for all terminations (Sn(96-96.5%),
Ag(3.0-3.5%) and Cu(0.5%)).

- vii -
Preface
SVHC / REACH
To minimize the environmental impact and take more responsibility to the earth
we live, Arbor hereby conrms all products comply with the restriction of SVHC
(Substances of Very High Concern) in (EC) 1907/2006 (REACH --Registration,
Evaluation, Authorization, and Restriction of Chemicals) regulated by the
European Union.
All substances listed in SVHC < 0.1 % by weight (1000 ppm)
Warning
Single Board Computers and their components contain very delicate
Integrated Circuits (IC). To protect the Single Board Computer and its
components against damage from static electricity, you should always follow the
following precautions when handling it :
1. Disconnect your Single Board Computer from the power source when you
want to work on the inside.
2. Hold the board by the edges and try not to touch the IC chips, leads or
circuitry.
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that comes
with the Single Board Computer, whenever components are separated from
the system.
Replacing Lithium Battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery type
recommended by the manufacturer.
Do not throw lithium batteries into the trash-can. It must be disposed of in
accordance with local regulations concerning special waste.
Technical Support
If you have any technical difculties, please do not hesitate to call or e-mail our
customer service.
http://www.arbor.com.tw
E-mail:[e-mail]

- viii -
Preface
Warranty
This product is warranted to be in good working order for a period of two years
from the date of purchase. Should this product fail to be in good working order
at any time during this period, we will, at our option, replace or repair it at no
additional charge except as set forth in the following terms. This warranty does
not apply to products damaged by misuse, modications, accident or disaster.
Vendor assumes no liability for any damages, lost prots, lost savings or any
other incidental or consequential damage resulting from the use, misuse of, or
inability to use this product. Vendor will not be liable for any claim made by any
other related party.
Vendors disclaim all other warranties, either expressed or implied, including but
not limited to implied warranties of merchantability and tness for a
particular purpose, with respect to the hardware, the accompanying product’s
manual(s) and written materials, and any accompanying hardware. This limited
warranty gives you specic legal rights.
Return authorization must be obtained from the vendor before returned
merchandise will be accepted. Authorization can be obtained by calling or
faxing the vendor and requesting a Return Merchandise Authorization (RMA)
number. Returned goods should always be accompanied by a clear problem
description.

- 1 -
1Chapter 1
Introduction
Chapter 1 - Introduction

- 2 -
Introduction
1.1. The Product
The EasyBoard-882E is a 3.5” compact CPU board
loaded with Intel®Core™ i7-3517UE processor,
Intel®PCH QM77 chipset and Intel®Graphics Media
Accelerator 4000. The board is provided with two
serial ports with RS232/RS422/RS485 supports, six
USB ports, two serial ATA port and one CFast socket
for storage, and one DVI-I port for video output. The
board supports dual independent display to answer the market need for video
performance.
1.2. About this Manual
This manual is intended for experienced users and integrators with hardware
knowledge of computers. If you are not sure about the description in this manual,
consult your vendor before further handling.
We recommend that you keep one copy of this manual for the quick reference
for any necessary maintenance in the future. Thank you for choosing ARBOR
products.

- 3 -
Introduction
1.3. Specications
Form Factor 3.5" Compact Board
CPU Soldered onboard Intel® Core™ i7-3517UE 1.7 GHz processor
Chipset Intel® PCH QM77
System Memory 1 x 204-pin SO-DIMM socket, supporting up to 8GB 1333/1600MT/s
DDR3 SDRAM
Graphics Chipset Integrated Intel® HD Graphics 4000
Graphics Interface
DVI-I: Analog RBG support up to 2048 x 1536 @60Hz or TMDS
support up to 1920 x 1200 via Chrontel CH7318
LCD: Dual-channel 24-bit LVDS
Dual independent displays support
Ethernet
1 x Intel® 82579LM PCIe GbE PHY with iAMT support
1 x Intel®82583V PCIe GbE controller
Super IO Chipset Fintek F71869ED
BIOS AMI®PnP Flash BIOS
Audio Realtek ALC662 HD Audio CODEC, MIC-in/ Line-out/Line-in
Storage
2 x Serial ATA ports with 600MB/s HDD transfer rate
1 x CFast socket
Serial Port 2 x COM ports (1 x RS-232 port, 1 x RS-232/422/485 port selectable)
Universal Serial Bus
4 x USB 2.0 ports
2 x USB 3.0 ports
Expansion Bus
1 x Mini-card socket
1 x micro SIM socket
Power Requirement +12V DC
Power Consumption 3A@+12V (typical)
Operating Temp. -40°C ~ 85°C (-40°F ~ 185°F)
Operating Humidity 10% ~ 95% @ 85°C (non-condensing)
Watchdog Timer 1~255 levels reset
Dimension (L x W) 146 x 102 mm (5.7” x 4.0”)

- 4 -
Introduction
1.4. Inside the Package
Before starting to install the single board, make sure the following items are
shipped:
1 x EasyBoard-882E WT 3.5" Compact Board with cooler
1 x Driver CD
1 x Quick Installation Guide
If any of the aforelisted items is damaged or missing, contact your vendor
immediately.
1.5. Ordering Information
EasyBoard-882E 3.5” Intel®Core™ i7-3517UE Compact Board
CBK-06-77M3-00
Cable Kit
1 x SATA cable
1 x SATA power cable
2 x USB dual port cables
1 x Audio cable
1 x COM port cable

- 5 -
2Chapter 2
Getting
Started
Chapter 2 - Getting Started

- 6 -
Getting Started
2.1. Board Dimensions
42,3~42.6
5,3
6,7 3,38
98,58
8,84
142,77
21 60
104
101,96
146
Ø3,1
(22)
(34)
Unit: mm

- 7 -
Getting Started
2.2. Block Diagram
COM1~COM2
DDR3-1600/1333 MHz
Dual Channels 24-bit LVDS
1 x LVDS Connector
MIC/ Line-in / Line-out
HD Audio Link Realtek ALC662
HD CODEC MIC-in/ Line-in/ Line-out
GbE LAN
GbE LAN
Analog RGB
SATA 2
USB 3.0 Port 0 ~ 1
USB 2.0 Port 2 ~ 5
SATA0, 1
PCIe x1
(Lane6)
Intel 82579LM
GbE PHY
PCIe x1
(Lane5)
Intel 82583V
GbE Controller
LPC I/F
EmCORE-i77M3
EasyBoard-882E
3.5” form factor
System Block Diagram
Intel®
QM77
PCH
DMI2
(x4)
FDI
Soldered
onboard
Intel® Core
i7-3517UE
Processor
1 x RJ-45 Connector
1 x RJ-45 Connector
Fintek
F71869ED
1 x DVI-I
1 x DDR3
SO-DIMM socket
1 x CFast socket
2 x USB ports (Type A)
2 x SATA connectors
USB Port 8
PCIe x1
Mini-Card socket
Micro SIM socket
4 x USB ports (PH)
Power input
+12VDC
Display Port B
(2 x 600MB/s HDD transmitter rate)
Chrontel
CH7318C
Level shifter to DVI
DVI
COM1: RS-232
COM2: RS-232/422/485

- 8 -
Getting Started
2.3. Jumpers & Connectors
The board comes with some connectors to join some devices and also some
jumpers to alter the hardware conguration. The following in this chapter will
explicate each of these components one-by-one.
2.3.1. Layout
This section will provide an overview of this board, both the top and bottom sides.
Board Top
PWR1
ATX1
JFRT1
AUDIO1
USB2
USB3
COM2
CON1
PWROUT1
CPUF1
SATA2
SATA1
BAT1
LVDS1
COM1
INV1
DVI1
USB1
LAN2
LAN1
SIM1 CF1
12
17
15
18
16
51
52
203
204
7274
7173 1
2
MC1
DIMM1
JPWR1
JBAT1
JRS1
JSATA1
JVLCD1

- 9 -
Getting Started
Board Bottom
PWR1
ATX1
JFRT1
AUDIO1
USB2
USB3
COM2
CON1
PWROUT1
CPUF1
SATA2
SATA1
BAT1
LVDS1
COM1
INV1
DVI1
USB1
LAN1
LAN2
SIM1 CF1
12
17
15
18
16
51
52
203
204
7274
7173 1
2
MC1
DIMM1
JBAT1
JPWR1
JRS1
JSATA1
JVLCD1

- 10 -
Getting Started
2.3.2. Jumpers
JPWR1
Function: Sets the power mode between AT and ATX
Jumper Type: 2.00 mm pitch 1x3-pin header
Setting: Pin Description
1-2 ATX mode (default)
23 1
2-3 AT mode
23 1
Note to make consistent setting in BIOS | Advanced menu | ACPI Settings
| Power-Supply Type to avoid possible conict. See 3.2.1. ACPI Settings on
page 43.
Board Top
JPWR1