Arbor Technology ETX-PC/104+ User manual

- 1 -
Quick Installation Guide
Version 1.2
Em104P-i2313
85
Wide Range Temperature
ETX-PC/104+ Complex
Form Factor
ETX®CPU Module
CPU
Soldered onboard
Intel®Atom™ E3800
Processor
Video
Dual Channel 24-bit
LVDS, Analog RGB
and DDI supported
LAN
Realtek RTL8106E
PCIe 10/100 Base-T
Ethernet Controller
&
Realtek ASIX AX88179
USB GbE Controller
Audio
Realtek ALC886 HD
CODEC, MIC-in/ Line-in/
Line-out
I/O
PC/104+/ USB/ IDE/
COM/ LPT/ FDD/ CF
II/ SATA
If you have any technical di󰀩culties, please consult the user’s manual rst at:
ftp://ftp.arbor.com.tw/pub/manual
Please do not hesitate to call or e-mail our customer service when you still can not
nd out the answer.
http://www.arbor.com.tw
E-mail: [e-mail]
♦ Technical Support
Copyright® 2021 All Rights Reserved. 4041231300120P
85
Declaration of Conformity
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Technical Support
If you have any technical di󰀩culties, please consult the user’s manual rst at:
http://www.arbor-technology.com
Please do not hesitate to e-mail our customer service when you still cannot nd
out the answer.
E-mail:[e-mail]

- 2 -
Ordering Information
Em104P-i2313-WT-E3825
Wide Range Temperature EmETX-i2304 ETX
®
CPU
Module w/Intel
®
Atom™ Processor E3825 R2.0 + PBE-
1101 R1.0 ETX
®
carrier board
Em104P-i2313-WT-E3845
Wide Range Temperature EmETX-i2304 ETX
®
CPU
Module w/Intel
®
Atom™ Processor E3845 R2.0 + PBE-
1101 R1.0 ETX
®
carrier board
Before you begin installing your single board, please make sure that the following
materials have been shipped:
Packing List
Em104P-i2313 PC/104 plus module kit:
1 x EmETX-i2304 ETX
®
CPU Module
1 x PBE-1101 ETX
®
Carrier Board
1 x Quick Installation Guide
HS-2304-F1 Heat Spreader (114 x 95 x 18mm)
CBK-15-1101-00
Cable kit for PBE-1101
1 x Audio cable
2 x USB cables
2 x COM-port cables
1 x IDE cable
1 x LPT cable
2 x Ethernet cables
1 x VGA cable
1 x KB/MS cable
2 x SATA cables
1 x power cable (4 wires)
1 x power cable (2 wires)
Optional Accessories

- 3 -
Driver (7.8A) Installation
Windows 7
Driver Path
AUDIO \Audio\32bit_Win7_R273
\Audio\64bit_Win7_R273
CHIPSET \Chipset\Win32_64_10.1.17
Ethernet \Ethernet\Install_Win7_7076_11222013
Graphic \Graphic\32bit_36.15.0.1073
\Graphic\64bit_37.15.0.1073
Processor IO \Processor IO
TXE \TXE Patch
USB3.0 \USB3.0
Windows 10
Driver Path
AUDIO \Audio\Win32
\Audio\Win64
GPIO I2C\GPIO I2C\windows10 32_64
Graphic \Graphic\Win32
\Graphic\Win64
INF \INF\Win32_64_10.1.17
LAN \LAN\0023-Install_Win10_10025_03202018\Install_Win10_10025_03202018
TXE \TXE\11.07

- 4 -
Specifications
Form Factor ETX-PC/104-Plus Complex CPU Module
CPU Intel® Atom™ Processor E3825 dual-core 1.33GHz
or E3845 quad-core 1.91GHz
System Memory 1 x 204-pin SO-DIMM socket up to 8GB DDR3L 1333MT/s
SDRAM
Graphic Chipset SoC integrated Intel® Gen 7 graphic
Ethernet
1 x Realtek RTL8106E 10/100 Base-T Ethernet from CPU
module
1 x ASIX AX88179 USB GbE from PBE-1101
BIOS Insyde BIOS
Serial ATA 2 x Serial ATA with 300MB/s HDD transfer rate
IDE Interface 1 x IDE (Ultra ATA 33), support 2 IDE devices
Serial Port 4 x COM ports
(COM1,3,4: RS-232, COM2: RS-232/422/485 selectable)
Parallel Port/ Floppy 1 x SPP/EPP/ECP mode
KB/MS One 1x6-pin wafer connector for PS/2 interface for keyboard
and mouse
Universal Serial Bus 4 x USB 2.0 ports
Graphics Interface
Analog RGB supports resolution up to 2048 x 1536
24-bit Dual Channel LVDS supported via eDP to LVDS NXP
PTN3460
1 x DDI port connector on the module
Expansion Interface
1 x CF II socket shared with IDE1
1 x PCI/104 PCI bus
1 x PC/104 ISA bus
Operating Temp. -40ºC ~ 85ºC (-40ºF ~ 185ºF)
Watchdog Timer 1~255 levels Reset
Dimension (L x W) 114 x 95 mm (4.5” x 3.7”)

- 5 -
Board Dimensions
0
2.5
9.91
89.92
92.5
0313.46
313.46
111
99.19
2.5
13.72
92.5
95
114
111
99.19
87.38
Unit: mm
3
50
1
2526
+
21
910
21
9 10
2
9
10 2
1
9
10
10
91
2
1
20
19
1 2
2019
1 2
A1
B1
A32 B32
D19
C19
D0 C0
1
220
19
1
44
43
2
1
1
1
1
1
1
2
9 10
1
2
1 1 1
4
3
21
1 14
13 26
2
30
29 1
D1 C1 B1 A1
D30C30B30A30
6
1
S
1
1
8
5
1
16
15
12
12VGND

- 6 -
Connectors Quick Reference
3
50
1
2526
+
21
910
21
9 10
2
9
10 2
1
9
10
10
91
2
1
20
19
1 2
2019
1 2
A1
B1
A32
B32
D19
C19
D0
C0
1
2
20
19
1
44
43
2
1
1
1
1
1
1
2
9 10
1
2
1
1
1
4 3
21
1 14
13 26
2
30
29 1
D1
C1
B1
A1
D30C30B30A30
6
1
S
1
1
8
5
1
16
15
12
12VGND
DIO1
1
AUDIO1
2
USB2
3
USB1
4
VGA1
5
COMB
6
COMA
7
LPT1
8
KBM1
9
FAN2
10
PWR1
12
JFRT1
14
TV1
11
JCOM1
13
LVDS1
15
INV1
16
IR1 17
JBAT1 26
JVLCD1 24
JBLON1 27
PC104+ 31
FAN1 30
JCFD1 29
CFD1 28
JRS2 23
IDE1 18
CONA1 19
LAN2 21
LAN1 22
LANLED 20
JWT1 25
Em104P-i2313

- 7 -
Em104P-i2313
Unit:mm
SO-DIMM
DDI
SATA1
SATA2
32
33
34

- 8 -
JumpersJumpers
JBAT1: Clear CMOS Setting (26)
Connector type: 2.00mm pitch 1x3-pin headers.
Pin Mode
1-2 Keep CMOS (Default)
23 1
2-3 Clear CMOS
23 1
JVLCD1: LCD Panel Voltage Selection (24)
The voltage of LCD panel could be selected by
JVLCD1 in +5V or +3.3V.
Connector type: 2.00mm pitch 1x3-pin headers.
Pin Voltage
1-2 +5V
23 1
2-3 +3.3V (Default)
23 1
JCFD1: CF IDE1 mode Selection (29)
Connector type: 2.00mm pitch 1x2-pin headers.
Pin Mode
Short Master 1 2
Open Slave (Default)
1 2
JWT1: WDT Mode Setting (25)
Connector type: 2.00mm pitch 1x3-pin headers.
Pin Mode
1-2 NMI
23 1
2-3 RST_SW (Default)
23 1
None Disable WatchDog Timer
JBLON1: LCD Backlight Selection (27)
The LCD panel backlight active mode could be
selected by JBLON1 in High or Low.
Connector type: 2.00mm pitch 1x3-pin headers.
Pin Mode
1-2 Active High (Default)
23 1
2-3 Active Low
23 1
JRS2: COM2 RS-232/422/485 Selection (23)
It can be congured COM2 to operate in RS-232,
RS-422 or RS-485 mode.
Connector type: 2.00mm pitch 2x3-pin headers.
Mode RS-232
(Default) RS-422 RS-485
1-2 ON OFF OFF
3-4 ON ON OFF
5-6 OFF ON ON
6
5
2
1
65
2
1
65
2
1

- 9 -
ConnectorsConnectors
DIO1: Digital I/O Connector (1)
DIO1 supports 8-bit In/ 8-bit Out.
Connector type: 2.00mm pitch 2x10-pin headers
Pin Description Pin Description
12
2019
1 DO0 2 DO1
3 DO2 4 DO3
5DO4 6 DO5
7DO6 8 DO7
9 GND 10 GND
11 DI0 12 DI1
13 DI2 14 DI3
15 DI4 16 DI5
17 DI6 18 DI7
19 +5V 20 +12V
AUDIO1: AC97 Connector (2)
Connector type: 2.00mm pitch 2x5 box headers.
Pin Desc. Pin Desc.
1 2
9 10
1Line_In_Left 2Line_In_Right
3GND 4GND
5MIC 6 N/C
7 GND 8GND
9 Speaker Left 10 Speaker Right
USB1 ~ 2: USB Connectors (4, 3)
Connector type: 2.00mm pitch 2x5-pin headers.
Pin Desc. Pin Desc.
1
9
2
10
1+5V 2+5V
3USBD- 4USBD-
5 USBD+ 6USBD+
7 GND 8GND
9 GND 10 N/C (Key)
Connector type: 2.00mm pitch 2x13-pin box headers.
Pin Description Pin Description
1
13
14
26
1STROBE# 14 AFD#
2 PTD0 15 Error#
3 PTD1 16 INIT#
4 PTD2 17 SLIN#
5PTD3 18 GND
6 PTD4 19 GND
7 PTD5 20 GND
8 PTD6 21 GND
9 PTD7 22 GND
10 ACK# 23 GND
11 Busy 24 GND
12 PE 25 GND
13 Select 26 N/C
COM A~B: RS-232 Connectors (6, 7)
Connector type: 2.00mm pitch 2x10-pin box headers.
Pin Description Pin Description
12
2019
1DCD#1 / 3 2RXD1 / 3
3TXD1 / 3 4DTR#1 / 3
5 GND 6DSR#1 / 3
7 RTS#1 / 3 8CTS#1 / 3
9 RI#1 / 3 10 N/C
11 DCD#2/ 4 12 RXD2/ 4
13 TXD2/ 4 14 DTR#2/ 4
15 GND 16 DSR#2/ 4
17 RTS#2/ 4 18 CTS#2/ 4
19 RI#2/ 4 20 N/C
VGA1: Analog RGB Connector (5)
Connector type: 2.00mm pitch 2x8-pin box headers.
Pin Description Pin Description
1
2
16
15
1 RED 2 GREEN
3BLUE 4 N/C
5 GND 6GND
7 GND 8GND
9N/C 10 GND
11 N/C 12 VDDAT
13 HSYNC 14 VSYNC
15 VDCLK 16 N/C
LPT1: Parallel Port Connector (8)

- 10 -
KBM1: Keyboard & Mouse Connector (9)
Connector type: 2.0mm pitch 1x6-pin box wafer
connector.
Pin Description
1KB_DATA
2GND
3MS_DATA
4KB_CLK
5 KB_VCC
6MS_CLK
FAN2: Fan Power Connector (10)
FAN2 is a 3-pin headers for the fan. The fan must be
a +12V fan.
Pin Description
1
2
3
1GND
2+12V
3 N/C
TV1: TV-out Connector (11)
Connector type: 2.00mm pitch 1x6-pin box wafer
connector
Composite Video
1CVBS 2GND
3Unused 4GND
5Unused 6GND
S-Video
1Unused 2GND
3Luminance 4GND
5Chrominance 6GND
JCOM1: RS-422/485 Connector (13)
Connector type: 2.00mm pitch 1x4 box wafer
connector.
Pin RS-422 RS-485
1
2
3
4
1TX+ DATA+
2TX- DATA-
3RX+ N/C
4RX- N/C
PWR1: Power Supply Connector (12)
Connector type: Terminal blocks.
Pin Description
1
2
3
4
5
6
1+12V
2GND
3GND
4GND
5 +5V
6+5V
JFRT1: Switches and Indicators (14)
It provides connectors for system indicators that
provides light indication of the computer activities
and switches to change the computer status.
Connector type: 2.00mm pitch 2x5-pin headers.
Pin Description Pin Description
109
1 2
1RESET+ 2GND
3POWER_LED+ 4POWER_LED-
5 HDD_LED+ 6HDD_LED-
7 SPEAKER+ 8SPEAKER-
9None 10 GND

- 11 -
Pin Desc. Pin Desc.
1
2930
2
2 VDD 1 VDD
4TX2CLK+ 3TX1CLK+
6TX2CLK- 5 TX1CLK-
8GND 7 GND
10 TX2D0+ 9 TX1D0+
12 TX2D0- 11 TX1D0-
14 GND 13 GND
16 TX2D1+ 15 TX1D1+
18 TX2D1- 17 TX1D1-
20 GND 19 GND
22 TX2D2+ 21 TX1D2+
24 TX2D2- 23 TX1D2-
26 GND 25 GND
28 TX2D3+ 27 TX1D3+
30 TX2D3- 29 TX1D3-
LVDS1: LVDS LCD Connector (15)
The LVDS connector on board 30-pin headers and
supports 18/36-bit
INV1: LCD Inverter Connector (16)
Connector type: 2.00mm pitch 1x5-pin box wafer
connector.
Pin Description
1
2
3
4
5
1+12V
2GND
3Backlight on/o󰀨
4Brightness control
5 GND
IDE1: Primary IDE Connector (18)
Connector type: 2.00mm pitch 2x22-pin box headers
1 2
43 44
Pin Description Pin Description
1RESET# 2GND
3DATA7 4DATA8
5DATA6 6DATA9
7DATA5 8 DATA10
9DATA4 10 DATA11
11 DATA3 12 DATA12
13 DATA2 14 DATA13
15 DATA1 16 DATA14
17 DATA0 18 DATA15
19 GND 20 N/C
21 DREQ 22 GND
23 IOW# 24 GND
25 IOR# 26 GND
27 IRDY 28 IDSEL
29 ACK# 30 GND
31 IRQ 32 N/C
33 AD1 34 ATA66 DETECT
35 AD0 36 AD2
37 CS#2 38 CS#3
39 ACT# 40 GND
41 +5V 42 +5V
43 GND 44 GND
CONA1: PC/104 ISA bus Slot (19)
IR1: Infrared Connector (17)
Connector type: 2.54mm pitch 1x5-pin headers.
Pin Description
1
2
3
4
5
1+5V
2 N/C
3IRRX
4GND
5 IRTX

- 12 -
LANLED: LAN LED Indicators (20)
Connector type: 2.54mm pitch 2x2-pin headers
Pin Description
21
43
1-2 -ACTLED
3-4 -LILED
LAN1~2: Ethernet Connectors (21, 22)
Connector type: 2.00mm pitch 2x5-pin headers
Pin Desc. Pin Desc.
1
9
2
10
1TX_MDI0+ 2TX_MDI0-
3RX_MDI1+ 4MDI2+
5MDI2- 6RX_MDI1-
7MDI3+ 8MDI3-
9N/C 10 N/C (Key)
CFD1 : Compact Flash Disk socket
(share with IDE1) (28)
FAN1: System Fan Power Connector (30)
FAN1 is a 3-pin headers for the CPU fan. The fan
must be a +5V fan.
Pin Description
1
2
3
1 N/C
2+5V
3GND
PC104+: PC/104+ PCI Bus Expansion
Slot (31)