Arbor Technology Em104P-i2313 User manual

1
Em104P-i2313
Wide Range Temperature
ETX-PC/104-Plus Complex
User’s Manual
Version 1.2
85
2021.03
85

- 2 -
Revision History
Version Release Time Description
1.0 Nov, 2014 Initial release
1.1 Sep,2016
1.Modify Orderding information
- Delete CBK-16-1100-02
- Add CBK-16-1100-01
2.Modify LVDS’s pin denition
1.2 Mar, 2021
1. Update the Windows 10 driver
2. 2.1 Block Diagram: Update “Innodisk
6DB368L048”, “IDE”, “Realtek ALC886”
and “Realtek RTL8106E”.
3. Update 1.3 Specications.
4. Update 1.4 Board Dimension
5. Update 2.2.2 and 2.2.3 Jumpers and
Connectors.

- i -
Contents
Preface .............................................................................................iii
Copyright Notice....................................................................... iii
Declaration of Conformity......................................................... iii
CE ..................................................................................... iii
RoHS................................................................................. iv
SVHC / REACH................................................................. iv
About This User’s Manual ......................................................... v
Warning .....................................................................................v
Replacing the Lithium Battery ................................................... v
Technical Support...................................................................... v
Warranty................................................................................... vi
Chapter 1 - Introduction ..................................................................1
1.1. Packing List ........................................................................2
1.2. Ordering Information ..........................................................2
1.3 Specications .....................................................................4
1.4. Board Dimensions ..............................................................5
Chapter 2 - Installation ....................................................................7
2.1. Block Diagram ...................................................................8
2.2. Jumpers and Connectors ...................................................9
2.2.1. Quick Reference ......................................................9
2.2.2. Jumpers & Connectors Location............................10
2.2.3. Jumpers.......................................................................... 11
2.2.4. Connectors.....................................................................12
KBM1: Keyboard & Mouse Connector (9) .............................15
Chapter 3 - BIOS.............................................................................21
3.1. Main..................................................................................24
3.2. Advanced..........................................................................25
3.2.1. Boot Conguration .................................................26
3.2.2. IDE Conguration...................................................26
3.2.3. USB Conguration .................................................26
3.2.4. Audio Conguration................................................27
3.2.5. LAN Conguration..................................................27
3.2.6. LPSS & SCC Conguration....................................27
3.2.7. Miscellaneous Conguration ..................................28
3.2.8. Security Conguration............................................28

- ii -
Contents
3.2.9. Video Conguration................................................29
3.2.10. SATA Conguration ..............................................31
3.2.11. ACPI Table/Feature Control..................................32
3.2.12. Super I/O Conguration ......................................32
3.3. Security ............................................................................33
3.4. Power ...............................................................................34
3.4.1 Advanced CPU Control ...........................................35
3.5. Boot ..................................................................................37
3.6. Exit ...................................................................................39
Appendix.........................................................................................41
Appendix A. Watchdog Timer (WDT) Setting ..........................42

- iii -
Preface
Copyright Notice
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
Declaration of Conformity
CE
The CE symbol on your product indicates that it is in compliance with the
directives of the Union European (EU). A Certicate of Compliance is available
by contacting Technical Support.
This product has passed the CE test for environmental specications when
shielded cables are used for external wiring. We recommend the use of
shielded cables. This kind of cable is available from ARBOR. Please contact
your local supplier for ordering information.
This product has passed the CE test for environmental specications. Test
conditions for passing included the equipment being operated within an
industrial enclosure. In order to protect the product from being damaged by
ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the
use of CE-compliant industrial enclosure products.
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

- iv -
Preface
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference
that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
RoHS
ARBOR Technology Corp. certies that all components in its products are
in compliance and conform to the European Union’s Restriction of Use of
Hazardous Substances in Electrical and Electronic Equipment (RoHS) Directive
2002/95/EC.
The above mentioned directive was published on 2/13/2003. The main
purpose of the directive is to prohibit the use of lead, mercury, cadmium,
hexavalent chromium, polybrominated biphenyls (PBB), and polybrominated
diphenyl ethers (PBDE) in electrical and electronic products. Member states of
the EU are to enforce by 7/1/2006.
ARBOR Technology Corp. hereby states that the listed products do not
contain unintentional additions of lead, mercury, hex chrome, PBB or PBDB that
exceed a maximum concentration value of 0.1% by weight or for cadmium
exceed 0.01% by weight, per homogenous material. Homogenous
material is dened as a substance or mixture of substances with uniform
composition (such as solders, resins, plating, etc.). Lead-free solder is used for all
terminations (Sn(96-96.5%), Ag(3.0-3.5%) and Cu(0.5%)).
SVHC / REACH
To minimize the environmental impact and take more responsibility to the
earth we live, Arbor hereby conrms all products comply with the restriction

- v -
Preface
of SVHC (Substances of Very High Concern) in (EC) 1907/2006 (REACH
--Registration, Evaluation, Authorization, and Restriction of Chemicals)
regulated by the European Union.
All substances listed in SVHC < 0.1 % by weight (1000 ppm)
About This User’s Manual
This user’s manual provides general information and installation instructions
about the product. This User’s Manual is intended for experienced users and
integrators with hardware knowledge of personal computers. If you are not
sure about any description in this booklet. Please consult your vendor before
further handling.
Warning
Single Board Computers and their components contain very delicate
Integrated Circuits (IC). To protect the Single Board Computer and its
components against damage from static electricity, you should always follow
the following precautions when handling it :
1. Disconnect your Single Board Computer from the power source when you
want to work on the inside.
2. Hold the board by the edges and try not to touch the IC chips, leads or
circuitry.
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that comes
with the Single Board Computer, whenever components are separated
from the system.
Replacing the Lithium Battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery type
recommended by the manufacturer.
Do not throw lithium batteries into the trash-can. It must be disposed of in
accordance with local regulations concerning special waste.
Technical Support
If you have any technical di󰀩culties, please do not hesitate to call or e-mail our
customer service.
http://www.arbor-technology.com
E-mail:[e-mail]

- vi -
Preface
Warranty
This product is warranted to be in good working order for a period of two years
from the date of purchase. Should this product fail to be in good working order
at any time during this period, we will, at our option, replace or repair it at no
additional charge except as set forth in the following terms. This warranty does
not apply to products damaged by misuse, modications, accident or disaster.
Vendor assumes no liability for any damages, lost prots, lost savings or any
other incidental or consequential damage resulting from the use, misuse of,
or inability to use this product. Vendor will not be liable for any claim made by
any other related party.
Vendors disclaim all other warranties, either expressed or implied, including
but not limited to implied warranties of merchantability and tness for a
particular purpose, with respect to the hardware, the accompanying product’s
manual(s) and written materials, and any accompanying hardware. This limited
warranty gives you specic legal rights.
Return authorization must be obtained from the vendor before returned
merchandise will be accepted. Authorization can be obtained by calling or
faxing the vendor and requesting a Return Merchandise Authorization (RMA)
number. Returned goods should always be accompanied by a clear problem
description.

1Chapter 1
Introduction
Chapter 1 - Introduction

- 2 -
Introduction
1.1. Packing List
Before starting with the installation, make sure the following items are
shipped. If any item appears damaged or is missing, contact your vendor
immediately:
Em104P-i2313 PC/104 plus module kit:
1 x EmETX-i2304 ETX CPU Module
1 x PBE-1100-RG R3.3 ETX 3.0 Carrier Board
1 x Quick Installation Guide
If any of the above items is damaged or missing, contact your vendor
immediately.
1.2. Ordering Information
Em104P-i2313-WT-
E3825
Wide Range Temperature EmETX-i2304 ETX
®
CPU
Module w/Intel
®
Atom™ Processor E3825 R2.0 + PBE-
1101 R1.0 ETX
®
carrier board
Em104P-i2313-WT-
E3845
Wide Range Temperature EmETX-i2304 ETX
®
CPU
Module w/Intel
®
Atom™ Processor E3845 R2.0 + PBE-
1101 R1.0 ETX
®
carrier board
HS-2304-F1 Heat Spreader (114 x 95 x 18mm)
CBK-15-1101-00
Cable kit for PBE-1100
1 x Audio cable
2 x USB cables
2 x COM-port cables
1 x IDE cable
1 x LPT cable
2 x Ethernet cables
1 x VGA cable
1 x KB/MS cable
2 x SATA cables
1 x power cable (4 wires)
1 x power cable (2 wires)
Optional Accessories

- 3 -
Introduction
Driver (7.8A) Installation
Windows 7
Driver Path
AUDIO \Audio\32bit_Win7_R273
\Audio\64bit_Win7_R273
CHIPSET \Chipset\Win32_64_10.1.17
Ethernet \Ethernet\Install_Win7_7076_11222013
Graphic \Graphic\32bit_36.15.0.1073
\Graphic\64bit_37.15.0.1073
Processor IO \Processor IO
TXE \TXE Patch
USB3.0 \USB3.0
Windows 10
Driver Path
AUDIO \Audio\Win32
\Audio\Win64
GPIO I2C\GPIO I2C\windows10 32_64
Graphic \Graphic\Win32
\Graphic\Win64
INF \INF\Win32_64_10.1.17
LAN \LAN\0023-Install_Win10_10025_03202018\Install_Win10_10025_03202018
TXE \TXE\11.07

- 4 -
Introduction
1.3 Specications
Form Factor ETX-PC/104-Plus Complex CPU Module
CPU Intel®Atom™ Processor E3825 dual-core
1.33GHz or E3845 quad-core 1.91GHz
Memory 1 x 204-pin SO-DIMM socket, up to 8GB DDR3L
1333 MT/s SDRAM
Graphic Chipset SoC integrated Intel®Gen 7 graphic
Ethernet
1 x Realtek RTL8106E 10/100 Base-T Ethernet from CPU
module
1 x ASIX AX88179 USB GbE from PBE-1101
BIOS Insyde BIOS
Serial ATA 2 x Serial ATA with 300MB/s HDD transfer rate
IDE Interface 1 x IDE (Ultra ATA 33), support 2 IDE devices
Serial Port 4 x COM ports
(COM1,3,4: RS-232, COM2: RS-232/422/485 selectable)
Parallel Port 1 x SPP/EPP/ECP mode
KB/MS One 1x6-pin wafer connector for PS/2 interface for keyboard
and mouse
Universal Serial Bus 4 x USB 2.0 ports
Graphics Interface
24-bit Dual Channel LVDS supported via eDP to LVDS NXP
PTN3460
1 x DDI port connector on the module
Expansion Interface
1 x CF II socket shared with IDE1
1 x PCI/104 PCI bus
1 x PC/104 ISA bus
Operating Temp. -40ºC ~ 85ºC (-40ºF ~ 185ºF)
Watchdog Timer 1~255 levels Reset
Dimension (L x W) 114 x 95 mm (4.5” x 3.7”)

- 5 -
Introduction
1.4. Board Dimensions
0
2.5
9.91
89.92
92.5
0313.46
313.46
111
99.19
2.5
13.72
92.5
95
114
111
99.19
87.38
Unit: mm
3
50
1
2526
+
21
910
21
9 10
2
9
10 2
1
9
10
10
91
2
1
20
19
1 2
2019
1 2
A1
B1
A32 B32
D19
C19
D0 C0
1
220
19
1
44
43
2
1
1
1
1
1
1
2
9 10
1
2
1 1 1
4
3
21
1 14
13 26
2
30
29 1
D1 C1 B1 A1
D30C30B30A30
6
1
S
1
1
8
5
1
16
15
12
12VGND

- 6 -
This page is intentionally left blank.

2Chapter 2
Installation
Chapter 2 - Installation

- 8 -
Installation
2.1. Block Diagram
1 x SO-DIMM
socket
Audio AC Link
Analog R.G.B.
SATA 0,1
USB ports x4
COM1, 2
LPT1/ FDD
IrDA
KB, MS
LPC
4 x PCI
PCIe x1
USB 2.0
USB 2.0
PCIe x1
10/100
BASE-T
DDI Dual Cannels
24-bit LVDS
DP
Single Channel DDR3L
1333MT/s
PCIe x1
LPC
4 x USB
Audio
PCI-104
GbE
COM3, 4
ISA Bus
PC/104
KB, MS
LPT
IrDA
LVDS
VGA
1 x IDE
1 x CF
IDE
1 x LAN
Master
FINTEK
F85226AF
PCIe to PCI
TI XIO2001
Realtek
ALC886
COM3~4
FPC
Connector
NXP
PTN3460BS
COM1~2
Primary
Super IO
F71869
2 x SATA
Coonector
Intel®Atom
E3825 1.33GHz
E3845 1.91GHz
Processor
1 x LAN
2nd LAN
Controller
ASIX
AX88179
USB to UART
FT2232
Innodisk
6DB368L048
1st LAN
Controller
Realtek
RTL8106E

- 9 -
Installation
2.2. Jumpers and Connectors
Jumpers
Label Function
(29)JCFD1 CF IDE1 mode Selection
(27)JBLON1 LCD Backlight Selection
(26)JBAT1 Clear CMOS Setting
(25)JWT1 WDT Mode Setting
(24)JVLCD1 LCD Panel Voltage Selection
(23)JRS2 COM2 RS-232/422/485 Selection
Connectors
Label Function
(1)DIO1 Digital I/O Connector
(2)AUDIO1 AC97 Connector
(3, 4)USB1 ~ 2 USB Connectors
(5)VGA1 Analog RGB Connector
(6, 7)COM A~B RS-232 Connectors
(8)LPT1 Parallel Port Connector
(9)KBM1 Keyboard & Mouse Connector
(10)FAN2 Fan Power Connector
(11)TV1 TV-out Connector
(12)PWR1 Power Supply Connector
(13)JCOM1 RS-422/485 Connector
(14)JFRT1 Switches and Indicators
(15)LVDS1 LVDS LCD Connector
(16)INV1 LCD Inverter Connector
(17)IR1 Infrared Connector
(18)IDE1 Primary IDE Connector
(19)CONA1 PC/104 ISA bus Slot
(20)LANLED LAN LED Indicators
(21, 22)LAN1~2 Ethernet Connectors
(28)CFD1 Compact Flash Disk socket (share with IDE1)
(31)PC104+ PC/104+ PCI Bus
2.2.1. Quick Reference

- 10 -
Installation
2.2.2. Jumpers & Connectors Location
Em104P-i2313
3
50
1
2526
+
21
910
21
9 10
2
9
10 2
1
9
10
10
91
2
1
20
19
1 2
2019
1 2
A1
B1
A32
B32
D19
C19
D0
C0
1
2
20
19
1
44
43
2
1
1
1
1
1
1
2
9 10
1
2
1
1
1
4 3
21
1 14
13 26
2
30
29 1
D1
C1
B1
A1
D30C30B30A30
6
1
S
1
1
8
5
1
16
15
12
12VGND
DIO1
1
AUDIO1
2
USB2
3
USB1
4
VGA1
5
COMB
6
COMA
7
LPT1
8
KBM1
9
FAN2
10
PWR1
12
JFRT1
14
TV1
11
JCOM1
13
LVDS1
15
INV1
16
IR1 17
JBAT1 26
JVLCD1 24
JBLON1 27
PC104+ 31
FAN1 30
JCFD1 29
CFD1 28
JRS2 23
IDE1 18
CONA1 19
LAN2 21
LAN1 22
LANLED 20
JWT1 25

- 11 -
Installation
2.2.3. Jumpers
JBAT1: Clear CMOS Setting (26)
Connector type: 2.00mm pitch 1x3-pin headers.
Pin Mode
1-2 Keep CMOS (Default)
23 1
2-3 Clear CMOS
23 1
JCFD1: CF IDE1 mode Selection (29)
Connector type: 2.00mm pitch 1x2-pin headers.
Pin Mode
Short Master 1 2
Open Slave (Default)
1 2
JWT1: WDT Mode Setting (25)
Connector type: 2.00mm pitch 1x3-pin headers.
Pin Mode
1-2 NMI
23 1
2-3 RST_SW (Default)
23 1
None Disable WatchDog Timer
JBLON1: LCD Backlight Selection (27)
The LCD panel backlight active mode could be selected by JBLON1 in High or Low.
Connector type: 2.00mm pitch 1x3-pin headers.
Pin Mode
1-2 Active High (Default)
23 1
2-3 Active Low
23 1

- 12 -
Installation
2.2.4. Connectors
JVLCD1: LCD Panel Voltage Selection (24)
The voltage of LCD panel could be selected by JVLCD1 in +5V or +3.3V.
Connector type: 2.00mm pitch 1x3-pin headers.
Pin Voltage
1-2 +5V
23 1
2-3 +3.3V (Default)
23 1
JRS2: COM2 RS-232/422/485 Selection (23)
It can be congured COM2 to operate in RS-232, RS-422 or RS-485 mode.
Connector type: 2.00mm pitch 2x3-pin headers.
Mode RS-232
(Default) RS-422 RS-485
1-2 ON OFF OFF
3-4 ON ON OFF
5-6 OFF ON ON
6
5
2
1
6
5
2
1
6
5
2
1
DIO1: Digital I/O Connector (1)
DIO1 supports 8-bit In/ 8-bit Out.
Connector type: 2.00mm pitch 2x10-pin headers
Pin Description Pin Description
12
2019
1 DO0 2 DO1
3 DO2 4 DO3
5 DO4 6 DO5
7 DO6 8 DO7
9 GND 10 GND
11 DI0 12 DI1
13 DI2 14 DI3
15 DI4 16 DI5
17 DI6 18 DI7
19 +5V 20 +12V