Arbor Technology FPC-7200 Series User manual

FPC-7200 Series
Fanless Intel® Atom™ D2700 Box PC
User’s Manual
Version 1.0
2012.03
P/N: 4012720000100P

This page is intentionally left blank.

- I -
Index
Contents
Chapter 1 - General Information..................................................................1
1.1 Introduction..................................................................................2
1.2 Packing List..................................................................................3
1.3 Ordering Information...................................................................3
1.4 The Installation Paths of CD Driver............................................4
1.5 Specications...............................................................................5
1.6 Dimensions...................................................................................7
1.7 Locating Controls and Connectors............................................8
1.8 Connecting Peripherals...............................................................8
1.8.1 DVI-I/DVI-D Video Outputs...............................................9
1.8.2 Serial Ports (COM1 ~4) ....................................................9
1.8.3 LAN Ports........................................................................10
1.8.4 USB Ports .......................................................................10
1.8.5 Keyboard and Mouse.....................................................11
1.8.6 Expansion PCIe Slot......................................................11
1.8.7 Audio Line-out/Mic-in.....................................................11
1.8.8 DC Power Input and Power ON/OFF Button................12
Chapter 2 - The Engine of FPC-7200.........................................................13
2.1 Board Layout..............................................................................14
2.2 Jumpers and Connectors..........................................................15
2.2.1 Jumpers & Connectors List..........................................15
2.2.2 Jumper Setting...............................................................16
JBAT1: Clear CMOS Setting.........................................16
JP1: RS485 AUTOFLOW Selector................................16
JP2: COM3, COM4 PORT RS232/485 MODE Selector16
JP3: COM3 PORT RS232/485 MODE Selector............17
JP4: COM4 PORT RS232/485 MODE Selector............17
2.2.3 Pin Assignments for Connectors .................................18
DIO1: Digital I/O Box Header........................................18
BZ1: Buzzer Pin Header ...............................................18
DP1: External 80 Port Pin Header................................18
RSTB1: Reset Button Pin Header................................19
FAN1-2: FAN Connectors.............................................19
Chapter 3 - Installation and Maintenance.................................................21
3.1 Memory & Mini-card Installation...............................................22
3.1.1 Removing Top Cover.....................................................22
3.1.2 Installing Memory Module.............................................23
3.1.3 Installing HSUPA/WiFi Module......................................24
3.2 How to Access CFast/SIM Card................................................27

- II -
Index
3.3 Hard Disk Drive & Riser Card Installation................................29
3.3.1 Removing Bottom Cover...............................................29
3.3.2 Installing Hard Disk Drive..............................................29
3.3.2 Installing Riser Card......................................................31
3.4 Wall Mounting (Optional)...........................................................32
3.5 Grounding the Box PC...............................................................32
3.6 Wiring the DC-Input Power Source ..........................................33
Chapter 4 - Driver & AP..............................................................................35
4.1 Preliminary work........................................................................36
4.2 Drivers.........................................................................................37
4.2.1 CHIPSET..........................................................................37
4.2.2 VGA .................................................................................40
4.2.3 Audio...............................................................................43
4.2.4 LAN..................................................................................46
Chapter 5 - BIOS.........................................................................................49
5.1 BIOS Main Setup........................................................................50
5.2 Advanced Settings.....................................................................51
5.2.1 ACPI Settings.................................................................52
5.2.2 CPU Conguration ........................................................53
5.2.3 IDE Conguration..........................................................54
5.2.4 USB Conguration ........................................................55
5.2.5 F81866 Super IO Conguration ...................................56
5.2.6 F81866 H/W Monitor......................................................57
5.3 Chipset Settings.........................................................................58
5.3.1 Host Bridge....................................................................59
5.3.2 South Bridge..................................................................60
5.4 Boot Settings..............................................................................61
5.5 Security.......................................................................................62
5.6 Save & Exit..................................................................................63
Appendix.....................................................................................................65
Appendix A: I/O Port Address Map.................................................66
Appendix B: Interrupt Request Lines (IRQ)...................................70
Appendix C: Memory Mapping .......................................................75
Appendix D: Digital I/O Setting.......................................................77
Appendix E: Watchdog Timer (WDT) Setting ................................79

- i -
Copyright Notice
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All
rights are reserved. No part of this document may be reproduced by any me-
chanical, electronic, or other means in any form without prior written permis-
sion of the manufacturer.
Declaration of Conformity
CE
The CE symbol on your product indicates that it is in compliance with the di-
rectives of the Union European (EU). A Certicate of Compliance is available
by contacting Technical Support.
This product has passed the CE test for environmental specications when
shielded cables are used for external wiring. We recommend the use of
shielded cables. This kind of cable is available from ARBOR. Please contact
your local supplier for ordering information.
Warning
This is a classAproduct. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference
that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class Adigital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment gen-
erates, uses, and can radiate radio frequency energy and, if not installed and

- ii -
used in accordance with the instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
RoHS
ARBOR Technology Corp. certies that all components in its products are in
compliance and conform to the European Union’s Restriction of Use of Haz-
ardous Substances in Electrical and Electronic Equipment (RoHS) Directive
2002/95/EC.
The above mentioned directive was published on 2/13/2003. The main pur-
pose of the directive is to prohibit the use of lead, mercury, cadmium, hexava-
lent chromium, polybrominated biphenyls (PBB), and polybrominated diphe-
nyl ethers (PBDE) in electrical and electronic products. Member states of the
EU are to enforce by 7/1/2006.
ARBOR Technology Corp. hereby states that the listed products do not con-
tain unintentional additions of lead, mercury, hex chrome, PBB or PBDB that
exceed a maximum concentration value of 0.1% by weight or for cadmium
exceed 0.01% by weight, per homogenous material. Homogenous material
is dened as a substance or mixture of substances with uniform composition
(such as solders, resins, plating, etc.). Lead-free solder is used for all termina-
tions (Sn(96-96.5%), Ag(3.0-3.5%) and Cu(0.5%)).
SVHC / REACH
To minimize the environmental impact and take more responsibility to the
earth we live, Arbor hereby conrms all products comply with the restriction of
SVHC (Substances of Very High Concern) in (EC) 1907/2006 (REACH --Reg-
istration, Evaluation, Authorization, and Restriction of Chemicals) regulated
by the European Union.
All substances listed in SVHC < 0.1 % by weight (1000 ppm)

- iii -
Important Safety Instructions
Read these safety instructions carefully
1. Read all cautions and warnings on the equipment.
2. Place this equipment on a reliable surface when installing. Dropping it or
letting it fall may cause damage
3. Make sure the correct voltage is connected to the equipment.
4. For pluggable equipment, the socket outlet should be near the equipment
and should be easily accessible.
5. Keep this equipment away from humidity.
6. The openings on the enclosure are for air convection and protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
7. Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
8. Never pour any liquid into opening. This may cause re or electrical
shock.
9. Never open the equipment. For safety reasons, the equipment should be
opened only by qualied service personnel.
10. If one of the following situations arises, get the equipment checked by
service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according
to the user’s manual.
e. The equipment has been dropped or damaged.
f. The equipment has obvious signs of breakage.
11. Keep this User’s Manual for later reference.

- iv -
Warning
The Box PC and its components contain very delicately Integrated Circuits
(IC). To protect the Box PC and its components against damage caused by
static electricity, you should always follow the precautions below when han-
dling it:
1. Disconnect your Box PC from the power source when you want to work on
the inside.
2. Use a grounded wrist strap when handling computer components.
3. Place components on a grounded antistatic pad or on the bag that came
with the Box PC, whenever components are separated from the system.
Replacing the Lithium Battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery type
recommended by the manufacturer.
Do not throw lithium batteries into the trashcan. It must be disposed of in
accordance with local regulations concerning special waste.
Technical Support
If you have any technical difculties, please consult the user’s manual rst
at: ftp://ftp.arbor.com.tw/pub/manual
Please do not hesitate to call or e-mail our customer service when you still can-
not nd out the answer.
http://www.arbor.com.tw
E-mail:[e-mail]
About This User’s Manual
This User’s Manual is intended for experienced users and integrators with
hardware knowledge of personal computers. If you are not sure about any
description in this User’s Manual, please consult your vendor before further
handling.

- v -
Warranty
This product is warranted to be in good working order for a period of one year
from the date of purchase. Should this product fail to be in good working order
at any time during this period, we will, at our option, replace or repair it at no
additional charge except as set forth in the following terms. This warranty does
not apply to products damaged by misuse, modications, accident or disaster.
Vendor assumes no liability for any damages, lost prots, lost savings or any
other incidental or consequential damage resulting from the use, misuse of, or
inability to use this product. Vendor will not be liable for any claim made by any
other related party.
Vendors disclaim all other warranties, either expressed or implied, including but
not limited to implied warranties of merchantability and tness for a particular
purpose, with respect to the hardware, the accompanying product’s manual(s)
and written materials, and any accompanying hardware. This limited warranty
gives you specic legal rights.
Return authorization must be obtained from the vendor before returned mer-
chandise will be accepted. Authorization can be obtained by calling or faxing
the vendor and requesting a Return MerchandiseAuthorization (RMA) number.
Returned goods should always be accompanied by a clear problem description.

- vi -
This page is intentionally left blank.