Arbor Technology EmCORE-i2702 User manual

- 1 -
Quick Installation Guide
Version 1.1
4041270200110PCopyright®2011 All Rights Reserved.
If you have any technical difculties, please consult the user’s manual rst at:
ftp://ftp.arbor.com.tw/pub/manual
Please do not hesitate to call or e-mail our customer service when you still can not
nd out the answer.
http://www.arbor.com.tw
E-mail: [e-mail]
♦ Technical Support
EmCORE-i2702
3.5” Miniboard
Form Factor
3.5” MiniBoard
VGA
Dual Channels 18-bit
LVDS/ Analog RGB /
TV-out
I/O
Mini-PCI/ SATA/ USB/
COM/ LPT
CPU
Soldered onboard Intel®
Atom™ N270 1.6GHz
CPU
LAN
2 x Realtek 8111C PCIe
Gigabit Ethernet
Audio
Realtek ALC655 AC97
Audio Codec, Line-in/ Line-
out/ Mic-in
Chipset
Intel® 945GSE
Intel® ICH7M
Declaration of Conformity
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

- 2 -
Ordering Information
Before you begin installing your single board, please make sure that the following
materials have been shipped:
Packing List
1 x EmCORE-i2702 3.5” Compact Board
1 x Driver CD
1 x Quick Installation Guide
EmCORE-i2702 Intel® N270 3.5” Compact Board
CBK-08-2702-00
Cable Kit
1 x USB Cable
1 x Ethernet Cable
1 x Audio Cable
1 x COM Cable
1 x IDE Cable
1 x LPT Cable
1 x KB/MS Y-Cable
1 x SATA Cable

- 3 -
The Installation Paths of CD Driver
Windows 2000 & XP
Driver Path
CHIPSET \CHIPSET\INF 9.2.0.1021
VGA \GRAPHICS\INTEL_2K_XP_32\1432
LAN \ETHERNET\REALTEK\8111_WINXP_5764
AUDIO \AUDIO\REALTEK_AC97\Win2K_XP_A406
Windows 7
Driver Path
CHIPSET \CHIPSET\INF 9.2.0.1021
VGA \GRAPHICS\INTEL_WIN7_32\1930
LAN Windows 7 built-in LAN driver
AUDIO \AUDIO\REALTEK_AC97\Win7_32_64_6305

- 4 -
Specications
Form Factor 3.5” Compact Board
CPU Intel® Atom™ N270 CPU 1.6GHz w/ 533MHz FSB
Chipset Intel® 945GSE + Intel® ICH7M
System Memory
1 x 200-pin DDR2 SO-DIMM Socket supporting 533MHz SDRAM
up to 2GB
(Optional soldered onboard 1GB DDR2 SDRAM)
Display Integrated Intel® Graphics Media Accelerator 950, Dual Channels
18-bit LVDS/ Analog RGB
Ethernet 2 x Realtek 8111C Gigabit Ethernet
I/O Chips ITE 8718F
BIOS Phonix-Award PnP Flash BIOS
Audio Realtek ALC655 AC97 Audio CODEC, MIC-in/Line-In/Line-Out
Storage
1 x Ultra ATA, support 2 IDE devices
2 x Serial ATA ports with 150MB/s HDD transfer rate
1 x CompactFlash Type II Socket (Shared with IDE1)
Serial Port 2 x COM ports (COM1: RS-232, COM2: RS-232/422/485
selectable)
Parallel Port 1 x LPT Port (SPP/EPP/ECP mode selectable)
KBMS 6-pin Mini-DIN connector for PS/2 standard Keyboard and Mouse
via Y-cable
Universal Serial Bus 4 x USB 2.0 ports
Expansion Interface 1 x Mini-PCI Socket
Operation Temp. 0oC ~ 60oC (32oF ~ 140oF)
Watchdog Timer 1~255 levels Reset
Dimension (L x W) 146 x 102 mm (5.7” x 4.0”)

- 5 -
Board Dimensions
0.00
0.00
8.84
142.77
Unit: mm
3.38
98.58
68.50
65.50
27.41
12.80
8.15
61.65
31.50
26.76
16.80
13.90
13.00
3.43
10.55
10.00
24.88
32.64
22.49
14.59
17.15
17.15
51.30

- 6 -
Jumpers/ Connectors Quick Reference
Connectors
Label Function
PWR1&2 DC 12V Power Input
AUDIO1 Audio Connector
COM1~2 Serial Port Connectors
DIO1 Digital I/O Connector
SYSF1 Fan Connector
IDE1 IDE Connector
INV1 LCD Inverter Connector
J8 SATA Power Connector
JCOM2 COM2 RS-422/485 Selection
JFRT1 Switches and Indicators
JSMB1 External SMBus Connector
CN2 LAN2 LED Indicator
RN1 Reset Button
CF1 Compact Flash TypeII Socket
SO-DIMM DDR2 SO-DIMM Socket (but-
tom Side)
KBMS1 Keyboard & Mouse
Connector
LAN1,
LAN2 Ethernet Connectors
LPT1 Parallel Port Connector
LVDS1 LVDS Connector
MINI-PCI1 Mini-PCI Socket
PWR3 ATX Feature Connector
SATA1~2 Serial ATA Connectors
TV1 TV-out Connector
USB1 USB Type A Connectors
USB2 USB Ports Pin Headers
VGA1 Analog RGB Connector
Jumpers
Label Function
JRS2 COM2 RS-232/422/485
Selection
JBAT1 Clear CMOS Setting
JPWR1 AT/ATX Power Mode Selection
JVLCD1 LCD Voltage Selection
J2 CF Master/ Slave Selection

- 7 -
Jumpers & Connectors Location
123 124
2
1
1
111
43
44
1
SATA1
SATA2
LPT1
COM2
JCOM2
AUDIO1
USB2
JFRT1
USB1
JRS2
LAN1
LAN2
VGA1
RN1
KBMS1
DIO1 MINI-PCI1
JPWR1
PWR3
JBAT1
COM1
PWR1&2
J8
SYSF1
TV1
INV1 JVLCD1
LVDS1
SO-DIMM
(On bottom side)
CN2
IDE1
CF1
(On bottom side)
JSMB1
J2
2
10
9
2
1
43
21
1
1
1
1 2
9 10
1
20
12
1
1
1
2
2
2
910 9
9
10
19
13
6
5
2
1
29
30
1
11
1
14
2
4
3
2
1
12
3
4
2
3 4 1
9
1
2
200
199
41 39
42
2
1
25
50
1
26

- 8 -
Jumpers
JVLCD1: LCD Panel Voltage Selection
The voltage of LCD panel could be selected by
JVLCD1 in +5V or +3.3V.
Connector type: 2.54mm pitch 1x3-pin headers.
Pin Voltage
1-2 +5V
23 1
2-3 +3.3V (Default)
23 1
JPWR1: AT/ATX Power Mode Selection
Connector type: 2.54mm pitch 1x2-pin headers.
Pin Mode
Short AT mode 1 2
Open ATX Mode (Default)
1 2
JRS2: COM2 RS-232/ 422/ 485 Selection
Connector type: 2.00mm pitch 2x3-pin headers.
Mode RS-232
(Default) RS-422 RS-485
1-2 Short Open Open
3-4 Open Short Open
5-6 Open Open Short
65
2
1
65
2
1
65
2
1
J2: CF IDE1 Mode Selection
Connector type: 2.00mm pitch 1x3-pin headers.
Pin Mode
1-2 Slave (Default)
2-3 Master
JBAT1: Clear CMOS Setting
Connector type: 2.00mm pitch 1x3-pin headers.
Pin Mode
1-2 Keep CMOS (Default)
23 1
2-3 Clear CMOS
23 1
Connectors
PWR1&2: ATX +12V Connector
PRW1&2 supplies the CPU operation ATX +12V
(Vcore).
Pin Desc. Pin Desc.
2
4
1
3
2 GND 1 GND
4+12V 3 +12V
J8: Small 4P Power Connector
Connector type: 2.54mm pitch 1x4-pin wafer one wall
90D connector
Pin Description
1
1+5V
2 GND
3GND
4+12V
INV1: LCD Inverter Connector
Connector type: 2.00mm pitch 1x5 box wafer
connector.
Pin Description
1
2
3
4
5
1+12V
2 GND
3 Backlight on/off
4 Brightness control
5GND
TV1: TV-out Connector
Connector type: 2.00mm pitch 1x6-pin box wafer
connector
Composite Video
1CVBS 2 GND
3Unused 4 GND
5Unused 6GND
S-Video
1Unused 2 GND
3Luminance 4 GND
5Chrominance 6GND
PWR3: ATX Feature Connector
Connector: onboard 3-pin power connector
Pin Desc.
1
1PS-ON
2 GND
3 5S_VB
23 1
23 1

- 9 -
JSMB1: External SMBUS Connector
Connector type: 2.54mm pitch 1x3 box-pin wafer
connector.
Pin Description
1
2
3
1SMB_Data
2SMB_Clock
3 SMB_Alert#
LVDS1: LVDS Connector
Connector type: DF-13-30DP-1.25V connector.
Pin Desc. Pin Desc.
1
2930
2
2 VDD 1 VDD
4TX2CLK+ 3 TX1CLK+
6TX2CLK- 5TX1CLK-
8 GND 7 GND
10 TX2D0+ 9TX1D0+
12 TX2D0- 11 TX1D0-
14 GND 13 GND
16 TX2D1+ 15 TX1D1+
18 TX2D1- 17 TX1D1-
20 GND 19 GND
22 TX2D2+ 21 TX1D2+
24 TX2D2- 23 TX1D2-
26 GND 25 GND
28 N/C 27 N/C
30 LVDS_DATA 29 LVDS_CLK
IDE1: Primary IDE Connector
Connector type: 2.00mm pitch 2x22-pin box headers.
1
2
43
44
Pin Description Pin Description
1RESET# 2 GND
3DATA7 4DATA8
5DATA6 6DATA9
7DATA5 8 DATA10
9DATA4 10 DATA11
11 DATA3 12 DATA12
13 DATA2 14 DATA13
15 DATA1 16 DATA14
17 DATA0 18 DATA15
19 GND 20 N/C
21 DREQ 22 GND
23 IOW# 24 GND
25 IOR# 26 GND
27 IRDY 28 IDSEL
29 ACK# 30 GND
31 IRQ 32 N/C
33 AD1 34 ATA66 DETECT
35 AD0 36 AD2
37 CS0# 38 CS1# (HD SELECT1#)
39 ACT# 40 GND
41 +5V 42 +5V
43 GND 44 N/C
SATA1~2: Serial ATA Connectors
Connector type: lockable SATA connectors with
housing. Support 150MB/s HDD transfer rate.
Pin Description
1 GND
2TX+
3TX-
4 GND
5RX-
6 RX+
7 GND

- 10 -
CF1: Compact Flash Type II Socket
Pin Description Pin Description
1 GND 26 GND
2PDD3 27 PDD11
3PDD4 28 PDD12
4PDD5 29 PDD13
5 PDD6 30 PDD14
6PDD7 31 PDD15
7PDCS1# 32 PDCS3#
8 GND 33 GND
9 GND 34 PDIOR#
10 GND 35 PDIOW#
11 GND 36 +5V
12 GND 37 PIDEIRQ
13 +5V 38 +5V
14 GND 39 CSEL#
15 GND 40 N/C
16 GND 41 IDERST#
17 GND 42 PIORDY
18 PDA2 43 PDDREQ
19 PDA1 44 PDDACK#
20 PDA0 45 HD_LED1#
21 PDD0 46 PDIAG#
22 PDD1 47 PDD8
23 PDD2 48 PDD9
24 N/C 49 PDD10
25 N/C 50 GND
JCOM2: RS-422/485 Output Connector
Connector type: 2.00mm pitch 1x4-pin box wafer
connector.
Pin RS-422 RS-485
1
2
3
4
1TX+ DATA+
2 TX- DATA-
3 RX+ N/C
4 RX- N/C
AUDIO1: AUDIO Connector
Connector type: 2.00mm pitch 2x5-pin box headers.
Pin Desc. Pin Desc.
1 2
9 10
1 Line_In_Left 2 Line_In_Right
3GND 4 GND
5 MIC 6 MIC2
7 GND 8 GND
9Speaker Left 10 Speaker Right
LPT1: Parallel Port Connector
Connector type: 2.00mm pitch 2x10-pin headers.
Pin Description Pin Description
1
19
2
20
1STB# 2AFD#
3PTD0 4 ERROR#
5PTD1 6 INIT#
7 PTD2 8 SLIN#
9PTD3 10 GND
11 PTD4 12 GND
13 PTD5 14 N/C (Key)
15 PTD6 16 BUSY
17 PTD7 18 PE
19 ACK# 20 SELECT