Arec LS-110 User manual

LS-110
Media Station
ENGLISHQuick Installation Guide
AREC Inc.© All Rights Reserved 2021. l www.arec.com
All information contained in this document is Proprietary

LS-110 Quick Installation Guide
FCC
Federal Communication Commission interference statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: -Reorient or relocate the receiving antenna. -Increase the
separation between the equipment and receiver. -Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. -Consult the dealer or an
experienced radio/TV technician for help.
RF Exposure Warning
The equipment complies with RF exposure limits set forth for an uncontrolled environment. The
antenna(s) used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
You are cautioned that changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may
cause undesired operation
This equipment should be installed and operated with a minimum distance of 20 centimeters
between the radiator and your body.
Notice: Any changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
CE
Hereby, AREC Inc., declares that this Media Station is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU.
1

2
LS-110 Quick Installation Guide
CB
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
– the ventilation should not be impeded by covering the ventilation openings with items, such as
newspapers,table-cloths, curtains, etc.:
– no naked flame sources, such as lighted candles, should be placed on the apparatus;
– attention should be drawn to the environmental aspects of battery disposal;
– the use of apparatus in tropical climates.
the instructions for use shall state that the apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

LS-110 Quick Installation Guide
3
Introduction
Specifications
Package Contents
Featuring a compact and stand-alone design, AREC LS-110 Media Station consists of diverse
features and functionality, including multi-signals capturing, recording synchronously, codec,
streaming online, live broadcasting, and web-based monitor page, providing complete
presentation or lecture capture solution.
Terminal Block
AREC Media Station
Media Station
LS-110
200mm(L) x 178mm(W) x 43mm(H)
1.37kg
12V/2A
24W (Max.)
0ºC ~ 40ºC / 90%
Supports two video inputs, including 1 video signal
interface (HDMI input) and up to two IP Cam/stream
signals. And output the transcoded video/audio to the
HDMI port and the HDMI loop.
Product Name
Model Name
Dimension
Weight
Power Requirement
Power Consumption (Max.)
Operating Temperature / Humidity
Maximum normal load description
Quick Installation Guide Power Adapter

LS-110 Quick Installation Guide
4
Product Appearance
Front Panel
Rear Panel
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Record function key
Streaming function key
Power
Front USB port
Power port
Audio input
Audio output
HDMI Loop(Video Output)
HDMI In(Video Input)
HDMI Out(Video Output)
Back USB port
Network port
RS-232
Reset button
NOTE: The LS-110 can detect and record to USB storage devices using FAT32, NTFS file systems.
NO. Name Brief introduction
Control the Record and Stop function
Turn live streaming on or off
Power on / off the device
1.For external USB storage device*
2.Firmware update via USB disk
3.Available for USB mouse, keyboard
4.Available for USB audio input (Note: Connecting an USB
audio device via an USB hub is not recommended. It may
cause compatibility issues.)
12V / 2A
Line audio input
Line audio output
HDMI loop through from input
HDMI input source
HDMI previe output
Available for external hard drive to increase storage
RJ-45 Ethernet connector for network connection
Captive screw connector for control over RS-232
Restoring devices to its factory default state
4
1 2 3
6 11 12 13 14 7 1098
5

LS-110 Quick Installation Guide
5
Connection
DV
USB
USB
RS-232
Speakerphone
Power
Line audio input
amplifier
projector
TV
projector
TV
Video output HDMI Video output HDMI
Speaker
Audio output
notebook
document cam
Video input HDMI
network
external hard disk
USB drive
USB Keyboard
USB mouse

LS-110 Quick Installation Guide
6
Accessing the Administrator pages
Log in Administrator with default username admin and password admin, then entering
System Administration webpages.
Use the RJ-45 Ethernet cable to connect an IP-based network to the LAN port. Enter the IP
address displayed in the lower right side of the screen in your browser to access the System
Administration webpage.
http://10.2.0.172
http://10.2.0.172
10.2.0.172

LS-110 Quick Installation Guide
7
Make sure the network camera are connected under the
same IP network (LAN)* and go to the [ Network device
manager ] page. After the scanning is done, click the
Login button and the authentication dialog will pop up.
Enter the username and password of the camera to
complete the authenticationand change the status to
[ OK ]. Then the camera is ready for video input
selection. Select the desired camera by its IP address.
For video source of encoder, enter RTSP or RTP
connection URL.
* For instance, the camera and LS-110 connected under
the same router with the same LAN address.
Setup
Step 1: Set up video input name, video source, PTZ control in [ Video inputs ] of [ Media I/O ].
The capture source can be from HDMI input, network camera, or encoder input.
If the desired video source is network camera, a login authentication with the camera is
required firstly in the [ Network device manager ] setup tab of [ Media I/O ].
Router(192.168.0.1)
LS-110(192.168.0.10)
IP Camera(192.168.0.20)

LS-110 Quick Installation Guide
8
Start a recording from the front panel
Press [ ] button and recording begins. The LED indicator of [ ] button is red to indicate
active recording.
Press [ ] button to end a recording.
Getting start a recording
Step 2: Set up audio volume in [ Audio ] of [ Media I/O ].
Step 3: Set up date and time of host machine in [ System settings ] of [ System ].

9
LS-110 Quick Installation Guide
The Online director allows user to control recording and have a live stream view of the output
video. The control panel makes it easy to apply layout, select background, and control the audio
recorded during the recording process.
Start a recording via the Online director
Entering the Online director webpage via [System Administration] by clicking the [ ] button
and opening a new tab; or log in Online director from the initial login page with default username
director and password director. Both ways lead to the Online director control panel for
web-based users.

LS-110 Quick Installation Guide
10
Important Security Policy
Precautions
1.Please open the product package carefully; we recommend you keep this packaging for
future transport, storage or maintenance use.
2.There are no switches or adjustment buttons required for operation inside this product, so
for your safety, please do not open the casing on your own, or vigorously rotate, shake or
use any other inappropriate ways to operate this product in order to avoid electrical shocks
and voiding the warranty. You can contact a local dealer directly if you have any questions.
3.Heat will be generated during the use of this product; therefore there must be sufficient
ventilation for the temperature of the unit to remain at a stable status. So please use the
product under normal environments to prolong the usage life, and avoid installing it in the
following environments.
Locations that are unstable or have incomplete planes
Locations with powerful magnetic fields
Locations where it is damp or may have water leakage
Locations that are too hot, close to heaters and air hoses, or be exposed to direct sun
light for long periods of time
Locations that are dusty
Locations where there are possible shocks
Locations close to power amplifiers
4.If you notice smoke or odor coming from the product, please quickly remove the power cable
and send it to a maintenance center for processing.
5.To avoid electrical shock, the plug of the adapter should be stably and completely inserted
into the power outlet and cannot be exposed; it must also have sufficient capacity to
withstand the current transmission. Please do not plug the adapter into the power outlet
before connecting the cable in order to avoid danger.
6.If not used for long periods of time, please unplug the power plug, and to ensure electrical
safety, when unplugging the adapter, please hold the plastic part of the adapter with dry
hands and then unplug the adapter. Please properly connect the cables according to the
printed instructions on the installation manual and the machine to ensure optimized usage
effects.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS

AREC Inc.© All Rights Reserved 2021. l www.arec.com
All information contained in this document is Proprietary
Made in Taiwan
Date : 2021.3.1
Version : 2.20