Argos 257/2471 User manual

MADE IN
BRITAIN
Dimensions
Width - 79.5cm
Depth - 44.5cm
Height - 73cm
Occasional Animal Print - Dressing Table
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 30/05/14
Important - Please read these instructions fully before starting assembly
ALR3051
257/2471

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 17kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
12 3
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
4 5
Top (DF1349)
(795 x 444mm)
Modesty (D1917A)
(761 x 280mm)
Drawer Base (T352-347)
(352 x 347mm) x 2
Left Drawer Front (DF821)
(377 x 126mm)
Divider (DF820)
(114 x 353mm)
Cross Rail (D1919A)
(761 x 96mm)
Left Side (D1915A)
(706 x 395mm)
7
10
6
Right Drawer Front (DF822)
(377 x 126mm)
Left Drawer Side (W453LH)
(350 x 95mm) x 2
Right Drawer Side (W453RH)
(350 x 95mm) x 2
Drawer Back (W341-95)
(341 x 95mm) x 2
Right Side (D1916A)
(706 x 395mm)
8 9
11
12

Please check you have all the fittings listed below
Tools required
Glue Safety - Take care when using glue, please follow the advice below
Skin contact: Remove contami-
nation by washing with soap and
water. This procedure should be
followed prior to aeting and
drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
3
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• From time to time check that
there are no loose screws on
this unit.
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 2
B
Metal dowel (F901) x 16
C
D E
Large locking
nut (F900) x 12
F
IG H
K
J
Rule Scissors Hammer Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Small locking
nut (F3) x 4
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Knock-in Peg (F171GY) x 8
T
Wedgefix (F639) x 4
S
M
Drawer runner (F1004) x 4
V
Plastic Nail (F91) x 4
L
N
9mm Screw (F73) x 8 9mm Screw (F74) x 4
19mm Screw (F461) x 4
13mm Screw (F79) x 1
Bracket (F327) x 1
Handle (F923) x 2

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 2 x 2
x 2
7 8
B
B
B
C
C
CC
10 11
Step 2
Prepare the 2 drawer
fronts
Screw 2 metal dowels
into the left drawer front
. and the right drawer
front .
Note: Tighten the metal
dowels up fully against
the panels.
B
7
8
Prepare the 2 pair of
drawer sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
10
11
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts and .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
10
11
7 8
C
C
10
11
10
11
B
B
7
B
B
Note: The right drawer
front has a shallow
identification mark.
8

Assembly Instructions
5
Step 4
x 2
x 2
x 2
x 2
E
E
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front and .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
12
10 11
7 8
9
10 11
12
9
9
E
Attach the handles
Attach a handle to
each of the drawer fronts
. and using 2
screws .
N
F
7 8
10 11
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
J
E
E
J
J
J
12
10
9
10
11
12
11
7 8
F
F
7 8 N

Assembly Instructions
6
Step 8
2
1
1
D
D
B
B
B
Finished
front edge
H
M
Finished front edge
Finished front edge
Finished front edge
a:
b:
c:
Prepare the left side
a: Place a runner on
the left side .
Slide back the top of
runner and use the 1st
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
on the left side .
c: Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
Screw 3 metal dowels
into the left side .
1
H
H
D
1
M
M
1
H
M
H
B
1
D

Assembly Instructions
7
Step 9
Prepare the right side
a: Place a runner on
the right side .
Slide back the top of
runner and use the 1st
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
on the right side .
c: Insert 2 large locking
nuts into the right
side .
Screw 3 metal dowels
into the right side .
2
H
H
D
2
M
M
2
B
2
Finished
front edge
Finished
front edge
H
M
H
M
2
Finished
front edge
2
Finished
front edge
2
H
D
B
D
B
B
a:
b:
c:

Assembly Instructions
8
Step 10
A
Prepare the cross rail
Insert 2 large locking
nuts into the cross rail
. .
Tap 2 wooden dowels
into the cross rail .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
D
D
A
10mm
A
D
5
A
5
plain chipboard surface
5
Finished
front edge
Finished
front edge
Step 11
Finished
front edge
B
D
Join the right side and
cross rail
Push the cross rail
onto the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the cross
rail .
Note: Turn the large
locking nut as far as it
will go - more than 1/2 a
turn.
5
2
5
2
D
5
D
D
D
D
D
plain chipboard surface
Prepare the modesty
Insert 4 large locking
nuts into the modesty
. .
Step 12
D
44
plain chipboard surface

Assembly Instructions
9
Step 13
Fit the modesty
Push the modesty
onto the right side .
Use a screwdriver to
tighten the 2large locking
nuts fitted to the
modesty .
2
4
2
4
E
Note: Support the
modesty until the left
side has been fitted in
the next step.
Note: The modesty
must be flush with
the top edge of the
right side.
4
Step 14
Fit the left side
Push the left side
onto the modesty
and the cross rail .
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the modesty and
cross rail .
1
4
4
D
5
1
6
5
plain chipboard surface
4