Argos Home Venice 806/9627 User manual

MADE IN
BRITAIN
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0330 016 1114
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Assembly Instructions - Important:Retain these instructions
for future reference
More help is available throughout this
booklet by scanning in the QR codes
or typing in the links
WARNING!
In order to prevent overturning, this product must be
used with the wall attachment device provided
Dimensions
Width - 152.3cm
Depth - 39.1cm
Height - 47.1cm
Venice - 1500 Wide TV Unit
Issue 6 - 20/11/19
806/9627
CR
CR
804/8411
803/8304

Components - Panels
Please check you have all the panels listed below
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• Regularly check all fastenings
to ensure that they are properly
tightened.
• Warning: This unit weighs
approximately 36kgs.
Please lift with care.
• Assembly to be carried out by
a competent adult only.
• Check you have all the
components and tools listed on
pages 1, 2, 4 and 4.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions
- otherwise a safety risk can
occur if incorrectly installed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall
using the overbalance
protector kit supplied.
• Dispose of all packaging
carefully and responsibly.
• Do not use this item if any
components are missing or
damaged.
Left Drawer Front (DF-00012886)
(71.9 x 21.6cm)
1Right Drawer Front (DF-00012887)
(71.9 x 21.6cm)
2
Drawer Base (TDF-00020643)
(67.6 x 34.7cm) x 2
5
Left Drawer Side (WRP-000000412LH)
(35 x 16.5cm) x 2
3Right Drawer Side (WRP-000000413RH)
(35 x 16.5cm) x 2
4
Drawer Back (WRP-000000414BCK)
(66.6 x 16.5cm) x 2
6

Components - Panels
Please check you have all the panels listed below
2
7 8Left Side (DF-00012879)
(43.6 x 38.9cm)
Right Side (DF-00012880)
(43.6 x 38.9cm)
Small Divider (DF-00017805)
(10.6 x 19.3cm)
10
Top (DF-00012878)
(152.3 x 39.1cm)
11
Fixed Shelf (DF-00012883)
(144.7 x 36.9cm)
13
Divider (DF-00012884)
(20.4 x 36.7cm)
9
Bottom Rail (DF-00012881)
(144.7 x 12.8cm)
14
Back Rail (DF-00012993)
(144.7 x 9.6cm)
15
Plinth Rail (DF-00012882)
(144.7 x 9.6cm) x 2
16
Back (X624-346)
(62.4 x 34.6cm) x 2
12

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
3
Bag 2
Bag 1
A C
Knock-in Peg (F171GY) x 8
D E
19mm Screw (F461) x 4
B
F
13mm Screw (F63) x 8
Small locking cam
nut (F3) x 4
Metal dowel (F901) x 4
A E
13mm Screw (F63) x 4
Metal dowel (F901) x 14
Large locking cam
nut (F900) x 14
G
H
Wooden dowel (F22) x 14
K
Hollow core
locking nut
(F892) x 4
L
Small metal dowel (F893) x 8
I
40mm Screw (F910) x 2
J
9mm Screw (F73) x 12
15mm Screw (F284) x 4
M
Nail (F51) x 24
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Wedge fix (F532) x 4
N

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
4
Pb
Pa
350mm long
CL
CR
CR Runner (F424) x 2
CL Runner (F422) x 2
Pc
Pd
Individual Fittings Bags
DR
DL
DL Runner (F425) x 2
DR Runner (F426) x 2
Overbalance protector
kit (F474) x 1
Q
R
Handle (FBARH128) x 2
336mm long
Drawer Brace (F420) x 2
O
Tools required
Rule
Scissors
Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
Bradawl
Flat-head
screwdriver
Spirit level

1 2
Assembly Instructions
5
Step 1
x 2
x 2
x 2
A
Prepare the left and
right drawer front
Screw 2 metal dowels
into each of the 2 drawer
fronts and .
Note: Tighten the metal
dowels up fully against
the panels.
A
1 2
A
A
A
A
12
hps://www.youtube.com/watch?v=HclfJdkm-Lg
Standard Drawer Box Assembly
B
A
B
B
BB
34
Step 2
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
B
3
4
Attach the drawer
sides to the drawer
fronts
Push the left drawer
sides . and right
drawer sides onto
the back of the drawer
fronts and .
Turn the small locking
nuts on the left
drawer sides and
right drawer sides .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
3
4
1 2
B
B
3
4
3
4
Step 1Use the Bag 2 for Steps 1 - 8
Note: Shallow
identification hole

1 2
Assembly Instructions
6
Step 4
C
C
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front and .
Step 5
5
34
1 2
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
6
3 4
5
6
6
C
3 4
C
C
5
3
4
6
5
3
4
Step 6
Attach the handles
Attach a handle to
each drawer front
and using screws .
D
1
2
x 2
x 2
x 2
R
R
D
D
1 2

Assembly Instructions
7
Step 7
Step 8
x 2
x 2
Fit runners to the
drawers
Fit the DL runner to
the bottom edge of the
left drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front and . Use a
bradawl to mark the
fixing positions, then
secure with 2 screws .
Fit the DR runner to
the bottom edge of the
right drawer side
using the same method.
4
P c
3
21
E
P d
4
3
P c
DL
E
E
DL
Runners must be
pushed up against
the drawer front
P d
E
E
DR
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounted Runners
Bradawl
Bradawl
Bradawl
Fit the drawer braces
Turn the 2 drawer
assemblies over and
hook a drawer brace
onto the bottom edge of
the drawer back .
Fix it to the drawer front .
. and and drawer
back using 2 screws
. .
O
F
O
F
O
F
FF
O
1 2
6
1 2
6
1 2
6

Assembly Instructions
8
Step 9
Prepare the right side
a: Fit a CR runner
to the right side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Mark the top hole of
the runner with a
bradawl and then fit a
screw .
c: Screw 6 metal
dowels into the right
side .
d: Push 2 hollow core
locking nuts into the
right side , making
sure that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut .
P b
8
8
J
J
E
P b
K
K
K
A
8
P b
J
1st
screw
Front edge
CR
Front edge
P b
Bradawl
K
KK
a:
b:
c:
d:
CR
J
J
J
P b
CR
E
CR
AA AA
A
CR
K
K
AA
Finished
front edge
Finished
front edge
Finished
front edge
Finished
front edge
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounted Runners
8
8
8
8
Use the Bag 1 for Steps 9 - end

Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 10
Step 11
Prepare the top
Screw 6 small metal
dowels into the holes
in the top .
Fit the bracket from the
overbalance protector kit
. to the shallow
mark-hole drilled into the
top using 1 of its
screws.
Note: Only fit 1 of the
screws, the other 1 will
be fitted later.
L
11
11
Q
Finished
front edge
Q
L
L
L
L
L
11
Fit the right side to
the top
Slide the right side
onto the top .
The 2 hollow core locking
nuts fitted to the right
side must slide over
the 2 small metal dowels
. fitted to the top .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
8
11
L
K K
L
8
11
K
K
CR
11
8
L
L