Argos Amalfi 1455056 User manual

Issue 1 -28/10/13
Important - Read these instructions fully before starting assembly
Assembly Instructions - Please keep for future reference 1455056
If you need help or have damaged or missing parts, call the Customer Helpline: 08456400800
Dimensions
Amalfi Table
Width - 91.5cm
Depth - 157.5cm
Height - 74cm

Important - Read these instructions fully before starting assembly
1
Care and maintenance
• This table top is a manufactured
composite materials made using mainly
PVC and processed wood powder, and
will keep it's beautiful natural looking
appearance with very little care and
maintenance. The use of harsh chemicals
or application of paint or varnish is not
approved and maybe affect the durability
of your product.
• Wash the table surface with mild soap
and water, rinse thoroughly and dry
completely.
• Do not use washing powders or any
abrasive substances which may scratch
the surface.
• As with natural wood products the
surface of your table can be damaged
by the effects of heat or radiation from
an external source such as a barbecue
grill, hot pans or reflection from glass in
extreme heat conditions, so please take
care with your table .
• Inspect and tighten all bolts and
fasteners on a regular basis to ensure
proper performance and safety of your
table.
• When moving the table, remove the
umbrella and lift. Do not drag this table.
• We recommend the use of furniture
covers when not in use.
• In order to prolong the life and beauty of
your table, we recommend that it be stored
in a dry and protected area when not in use.
• Do not use the table surface as a
chopping board or strike it with hard or
pointed items.
• Check you have all the components and
tools listed on page 2.
• Remove all fittings from the plastic bags
and separate them into their groups.
• Keep children and animals away from
the work area, small parts could choke if
swallowed.
• Make sure you have enough space to
layout the parts before starting.
• Do not stand or put weight on
the components during assembly, this
could cause damage.
• Assembly on a soft level surface to
avoid damaging the unit or your floor.
• Parts of the assembly will be easier
with 2 people.
• Dispose of all packaging carefully and
responsibly.
• Do not sit or stand on this table.
• A weighted umbrella base must be used
when using an umbrella with this table.
• Do not put very hot items directly on the
table surface.
• Warning: The unit weighs approximately
25.3 kgs. Please lift with care.
Safety and Care Advice
!

Note: The quantities below are the correct amount to complete the assembly.
6mm Hex Key
M6 x 50mm Bolt x 10 M6 x 16mm Bolt x 8
d6.5 x D10 x 1.6 Washer x 8 Bolt Cap M6 x 8
d6.5 x D13 x 1.0 Washer x 8
Components - Parts
Table Top x 1 Leg x 2 Support x 2
Ruler - Use this ruler to help correctly identify the screws
Tools required
Please check you have all the parts listed below
Components - Fittings
Please check you have all the fittings listed below
2
AB
E
Bolt Cap M6 x 10
F
C
D
12 3
16

Lay the table top on to a flat
even surface, such as carpet with
underside facing upwards.
Attached the legs to the
underside of the table top rim
by using bolts a shown in the
diagram. Do not tighten the bolts
at this time.
Step 1
Step 2
Assembly Instructions
3
2
3
3
3
C
B
D
1
1
2
A
F
A
B
Attach the supports to the
legs by using bolts ,
washers and .
Do not tighten the bolts this time.
B
C
CD
D
2
2
2
2
2
2
3
3
3
Incorrect assembly
3
2
1
1
Note:
The arrows on the legs indicate
the correct edge to fit to the table
rim and ensure correct
assembly-see diagram.
Note:
1. The arrow marks on the
supports should coincide
with Figure to ensure proper
assembly.
2. The tabs on the supports
should be facing towards the
inside to ensure proper
assembly.
!

4
Step 3
If you need help or have damaged or missing parts, call the Customer Helpline: 08456400800
Retailer: Argos
Address: 489-499 Avebury Boulevard Saxon Gate West, Central Milton Keynes Bucks, MK9, 2NW
Assembly Instructions
F
A
Fasten the supports to the
underside of the table top
rim by using bolts .
3
1
A
3
3
3
1
1
Step 4
Turn the table to its upright
position.
Note:
To use an umbrella with this
table, remove the plastic center
plug and put the umbrella pole
through the table top.
Assembly is completed.
At this point tighten all bolts and
cover with bolts and caps.
E
E