Argos Cheval 147/5634 User manual

MADE IN
BRITAIN
Dimensions
of each
cupboard
Width - 76cm
Depth - 39.5cm
Height - 50cm
Cheval - Overbed Cupboards
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 20/01/14
Important - Please read these instructions fully before starting assembly
ALR2971
147/5634
151/3314
146/9918
144/1390
We recommend that you assemble any
Cheval Robe(s) you may have purchased
BEFORE you assemble these cupboards.
This will enable you to measure the correct
space and height required for the cupboards.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: The combined
weight of the units is
approximately 47kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
brackets supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
12
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
4 5
6 7
Left Side (D2761A)
(484 x 372mm) x 3
Door (D2765A)
(480 x 373mm) x 6
Right Side (D2762A)
(484 x 372mm) x 3
Back (X738-476)
(738 x 476mm) x 3
Base (D2764A)
(728 x 371mm) x 3
Shelf (D2773A)
(727 x 350mm) x 3
3Top (D2763A)
(760 x 393mm) x 3

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
see malibu fitment mk2 for large number of panels and fittings
A
Wooden dowel (F22) x 12
B
Metal dowel (F901) x 24
C
D E
Large locking
nut (F900) x 24
F
G H I
J K
19mm Screw (F461) x 20
13mm Screw (F63) x 24
Handle (F273) x 6
25mm Screw (F50) x 12
Hanging bracket
(F849) x 6
Wall bracket (F198) x 6
Tools required
Rule
Scissors
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
Square
mm 10 20 30 40 50 60 70 80 90 100 mm 10 20 30 40 50 60 70 80 90 100
Connecting Sleeve (F432) x 8 Shelf stud (F110) x 12
L M
Hinge plate
(F523) x 12 Hinge (F518) x 12

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Prepare the left side
Screw 2 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Fit 2 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
Fit a hanging bracket
to the left side using
2 screws , making
sure that the hook is
towards the back edge.
Step 2
B
1
C
1
80% C
C
C
Prepare drawer fronts
and wraps x 3
a: Screw 2 metal dowels
. into the holes on the
back of the drawer fronts
. .
Note: Tighten the metal
dowels up fully against
the panels.
B
20
B
B
B
J
FF
L
L
L
1
L
1
J
F
1
Prepare the right side
Screw 2 metal dowels
into the right side .
Insert 2 large locking
nuts into the right
side .
Fit 2 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
Fit a hanging bracket
to the right side using
2 screws , making
sure that the hook is
towards the back edge.
B
2
C
2
L
2
J
F
2
C
C
B
B
J
F
F
L
L
L
2
Finished
front edge
Finished
front edge
These instructions will show you
how to build 1 overbed cupboard

Finished
front edge
A
Assembly Instructions
5
Fit the base to the
right side
Push the base onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 3
Step 4
C
C
C
C
A
A
A
10mm
A
Prepare the base
Tap 4 wooden dowels
into the base .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into the base .
A
5
C5
Finished
front edge
5
C
B
C
C
5
2
5
5
2
Fit the back
Slide the back along
the groove in the base
and on into the groove in
the right side .
Important: Make sure
that the cut-outs on the
back are at the top of
the assembly.
Step 5
2
6
5
Note: Support the
back panel until the
left side has been
fitted in the next step.
7
5
2
Cut-outs
at the top
7
7

Assembly Instructions
6
Step 6
Fit the left side
Push the left side
onto the base
making sure that the
back slots into the
groove.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Hold the back in
place and carefully stand
the unit up
C
1
5
7
5
1
5
7
7
Prepare the top
Screw 4 metal dowels
into the top .
B
3
B
B
B
B
Step 7
Fit the top
Lower the top down
onto the assembly,
making sure that the
back slots into its
groove.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the sides and .
Step 8
3
Finished
front edge
3
7
7
1 2
C
1
2
3

K
K
722mm
Assembly Instructions
7
Step 9
Step 10
18mm
37mm
722mm
18mm
K K
Outline of
the unit
To adjust the height of
the unit on the wall,
turn the bottom screw
Pull the unit up
against the wall
by tightening
the top screw
J
K
Warning: The
unit is heavy.
Lift with care.
Fit the unit to the wall
To fix the unit to the wall,
place the unit in the
required position and
lightly mark the outline of
the top corners of the
unit with a pencil.
Fit the 2 wall brackets
to the dimensions shown
in the top diagram.
The screws and plugs
are not supplied as they
need to be the correct
type to suit your wall.
Place your unit onto the
wall brackets , via the
hanging brackets
which you have fitted to
the sides and of
the unit.
Turn the lower screw in
the wall brackets to
adjust the height of the
unit.
Finally, pull the unit up
against the wall by
tightening the top screw
in the hanging brackets
. .
Warning: Take
care when
drilling the wall
that you do not drill into
any pipes, wires etc. If in
doubt, consult an expert.
K
K
J
1 2
J
J
IMPORTANT
If you are fitting these cupboards between
two robes or, a robe and a wall, please
measure the space required to fit the
cupboards and the height of the robe(s)
1
2

Assembly Instructions
8
Step 10
Joining units together
Fittings have been
supplied so you are able
to join the units together.
If required, position any
robes that you have
assembled up against
the cupboards.
Using a 5mm drill bit,
drill through the two
5mm part-drilled holes in
the side panel into the
adjoining side panel of
the other unit.
Push the connecting
sleeves into the holes
and then screw the
screws in from the
other side.
G
E
5mm G
E

Assembly Instructions
9
Step 11
Step 10
Hx 4
Fit the shelf
Insert 4 shelf studs at
the required height.
Lower the shelf down
onto the shelf studs .
4
H
4
H
Step 12
M
DD
90
M
Prepare the 2 doors
Push fit 2 hinges into
each of the doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
M
6
M
DD
6
M
DD
M
DD
6
D