Argos Harrington User manual

Harrington - 2 Drawer 2 Door Sideboard
614/4238
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call t h e A rgos Customer Helpline: 08456 400 800
Important  Please read these instructions fully before starting assembly
Dimensions
Width - 93cm
Depth - 45cm
Height - 80cm
137/6939
or Homebase Customer Helpline: 0845 077 8888.
Issue 1 - 10/09/13

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
for
inserting screws,
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

underside
Top panel (93 x 45cm)
1
Base panel (84,4 x 39,5cm)
2
Shelf (84,2 x 37,4cm)
3
Right side panel (77,5 x 40,8cm)
4
Left side panel (77,5 x 40,8cm)
5
Door x2
16
(43,6 x 36,8cm)
Drawer front x2
17
(36,8 x 14,9cm)
Drawer back x2
20
(33,3 x 14cm)
top
2
Front plinth (92,2 x 6,7cm)
15
Top front frame (79,2 x 4,7cm)
8
Middle front frame (79,2 x 4,7cm)
9
Bottom front frame (79,2 x 4,7cm)
10
Back column (69 x 4,7cm)
11
Vertical frame (44,1 x 4,6cm)
12
Small vertical frame
13
(15,4 x 4,7cm)
Side drawer runner
22
x2 (35 x 3,7cm)
Back panel x2 (71,8 x 42,7cm)
25
Middle drawer runner
21
(37,6 x 6,8cm)
Drawer bottom x2
24
(34,7 x 34,3cm)
Right front frame (77,5 x 4,6cm)
6
Left front frame (77,5 x 4,6cm)
7
Block x4
23
(6,5 x 2cm)
Components - Panels
Please check you have all the panels listed below
top
Side plinth x2
(
41,9 x 6,7cm)
14
18 Drawer right side x2
(35 x 14 cm)
19 Drawer left side x2
(35 x 14 cm)

3
Components - Fittings
Please check you have all the fittings listed below
If you have damaged or missing components,
Note:
fittings may be supplied than are required.
The quantities below are the correct amount to complete the assembly. In some cases more
Ruler- Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
2m
ABC
Wooden dowel x 56 30mm Screw x 64
F
G
Shelf support x 4
Door
hinge x 4
E
J
Nail x 32
Clip x 2 Plug x 2
HI
16mm Screw x 27
D
Drawer
handle x 4
K
Bracket x 1
L
Washer x 2
M
Wall strap x 1
35mm Screw x 4
or Homebase Customer Helpline: 0845 077 8888.
call the Argos Customer Helpline: 08456 400 800

Step 2
Step 1
Assembly Instructions
4
a: b: c:
C
23 C
4
6
Fixing right front frame
to the right side panel
.
(Two people required for
an easier assembly)
Insert right side panel
into right front frame
through joints.
a:
Note:
Before fixing the
blocks into
place it is important to
ensure that the slot and
groove of parts and
are fully pushed together
and lined up correctly at
the top and bottom.
C
c:
.
Fix through blocks
into front frame using
screws
b:Place blocks in the
to the side panel using
screws .
positions shown. First fix
C
6
4
46
23
23
23
Yes!No!
Top
30mm
23
23
4
a: b: c:
C
23 C
5
7
Yes!No!
23
5
23
7
30mm
Fixing left front frame
to the left side panel
.
(Two people required for
an easier assembly)
Insert left side panel
into left front frame
through joints.
a:
Note:
Before fixing the
blocks into
place it is important to
ensure that the slot and
groove of parts and
are fully pushed together
and lined up correctly at
the top and bottom.
C
c:
.
Fix through blocks
into front frame using
screws
b:Place blocks in the
to the side panel using
screws .
positions shown. First fix
C
5
5
7
23
23
23
7
0mm
0mm
(-)
(+)
(+)
(-)

Assembly Instructions
5
Step 3
Step 4
Insert dowels into the
indicated parts.
A
Insert shelf support pins
into side panels
F
4and .5
4
5
A
A
A
A
A
A
F
F
F
F
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
2
8
9
10
12
21
13
Assembling parts.
Put parts , , ,
and together as
shown in the diagram.
8 9 10 12
13 8
912
10
13
A
A
11
Note: Correct
position of parts as shown.
A
A
22
2x
(2x)
(2x)
18
19 A
A
Chanfred edges to be
facing down.

Assembly Instructions
6
Step 5
Insert the assembled
frame into the holes on
left side panel .
5
Step 6
Fixing panels.
Attach base panel to
the left side panel
using screw .
2
C
5
8
10
5
2
C
C
C
5
Step 7
4
2
C
C
C10
2
C
4Fit right side panel to
the front frames and base
panel, then fix it to the
base panel using
screws .
Attention to the holes

Assembly Instructions
7
Step 8
Step 9
a: b:
Fixing middle drawer
runner.
Important:
With help,
carefully stand the
product upright.
Fit middle drawer runner
to the small vertical
frame then fix using
screw .
13
C
21
C
21
I
K
10
2I
10
2
a: Fix bracket to the
pre drilled holes on base
panel using screws ,
as shown in the diagram.
b: Fix bracket to the
bottom front frame
using screw .
2I
I
10
K
K
Fixing bracket

Assembly Instructions
8
Step 10
Step 11
Fixing back column.
Fit back column to
the base panel and
middle drawer runner
then fix it using screw .
21
11
C
2
11
21
C
C
1
1
C
C
C
C
C
Fixing top panel
With help, fit top panel
to the cabinet, then attach
it using screws .
C

Assembly Instructions
9
Step 13
Step 12
22
22
C
C
C
22
With help, carefully
lay down the product.
Important:
a:Fix side plinths to
the side panels using
screws .
Make sure
side plinths are
aligned to the bottom and
front edges of the side
panels.
Note:
b:Fix front plinth
to the bottom front frame
using screws .
Make sure front
plinth is aligned to the
bottom edge of the side
panels and in line to the
side plinths.
Note:
14
C
15
10 C
15
b:
a:
a:
15
14
14
C
C
C
C
C
C
C
C
C
C
C
Fit the two drawer runners
, one in each side as
shown in the diagram and
fix them using screws .
Chanfred
edges to be facing up.

Assembly Instructions
Step 14
10
other door.
Repeat step 14 for the
Step 15
16
16 I
I
Fixing door.
With help, attach doors to
the pre drilled holes in the
cabinet using screws ,
as shown.
I
16
E
E
I
I
E
E
Attention
I
I
Profile View
With help carefully
stand the product upright.
Fitting hinges to doors.
I
E
Note
correct
position of the hinge as
shown in the diagram.
With doors facing
upwards, attach hinges
to the pre drilled holes in
the doors using screws .
Ensure countersunk detail
on hinge is uppermost.

Assembly Instructions
11
Step 17
Step 16
Attach handles to the
doors using screw .
B
D
I
H
B
B
D
D
I
H
I
a: b:
I
I
G
G
I
G
I
G
G
Repeat Step 17 for the
other door.
G H
I
Attach plug to the
pre-drilled holes in the
doors using screws .
a: Close the doors and
insert clips into plugs .
b: Fix clips using
screws .
Make sure doors are fully
closed and flush to the
front frames before fixing
clips .
G
Attention!

Assembly Instructions
12
Step 18
3
Insert shelf into the unit
on the support pins.
Make sure rounded edge
is facing front.
3
Rounded edge
Step 19
25
25
J
J
Fixing back panels.
MUST
Important:
Cabinet be
upright and square when
back panels are attached.
Attach the back panels
using nails .
J
25
3
Attention!

Assembly Instructions
Step 20
Step 21
17
18
19
24 20
a: b: c:
d:
(2X)
C
C
C
C
B
D
A A
Insert drawers into unit.
With the back of the
drawers past the front
frames, use a hammer to
tap dowels in flush to
drawer sides.
A
A
A
d:Using screw attach
the drawer handle to
the drawer front.
Drawer assembly.
a: Attach drawer sides
and to the drawer
using screws .
b:
C
B
D
24
17
18
20
C
19
front
c:
Slide drawer bottom
into slots on drawer sides
Attach drawer back
using screws .
Repeat Step 20 for the
other drawers.
This is a safety catch to
stop drawer falling out.
13

Assembly Instructions
14
Step 22 Note:Wall plugs are not supplied.
The correct type of fixing must
be used for your wall, seek
professional advice if in doubt.
wall
L
M
L
I
Fixing to wall.
Furniture must be fixed to
a wall. Fix wall strap to
top of furniture using
washer and screw .
With help, move furniture
into position.
M
I
L
Assembly is complete.
If you need help or have damaged or missing parts, c a l l t h e Customer Helpline: 08456 400 800

Important note:
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualifed
tradesperson if you are unsure.
1: General rule:
2:
3:
4:
5:
Hints:
Always use a larger screw and wall plug
if you are not sure.
Ensure you use the recommended drill bit to match the wall
plug and hole size.
Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls You can use one of the following types of wall plug if your
walls are made of brick, breeze block, concrete, stone or wood.
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
For use with plasterboard partitions or
hollow wooden doors.
For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
No.1General Purpose wall plug No.3Cavity Fixing wall plug No.5Hammer Fixing wall plug
No.2Plasterboard wall plug
No.4Cavity Fixing-Heavy Duty
wall plug
No.6Shield Anchor wall plug
Heavy loads
A Guide to -Wall Mounting & Fixings
Care &
Maintenance
Safety:Always check the fitting
and location to ensure your safety
in and around the home.
Fitting:From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.