Argos 617/3113 User manual

Storage Cupboard
Assembly Instructions -
Please keep for future reference
Dimensions
Depth - 35cm
Width - 70.1cm
Height - 86.5cm
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Verson 2 Date: 24/08/12
617/3113
617/3481

Care and maintenance
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals away
from the work area, small parts
could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand on the product,
this could cause damage.
• Assemble the item as close to
its nal position (in the same
room) as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
oor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Do not use this item if any
components are missing or
damaged.

2
Components - Panels
Please check you have all the panels listed below
Left side panel (78 x 32cm)
1
Right side panel
(78 x 32cm)
2
Top panel
(70 x 34.6cm)
3
Bottom panel (70 x 34.6cm)
5
Shelf
(65 x 31.9cm)
6
Back panel (80.7 x 67.6cm)
7
Door panel x 2 (77.4 x 33.8cm)
4
If you have damaged or missing components,
call the Customer Helpline: 08456 400800
Pilot holes for guidance only
Pilot holes for guidance only
Pilot holes for guidance only
Pilot holes for guidance only

15mm Locking nut x 2
3
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
Components - Fittings
110 120 130 140 1500 10 20 30 40 50 60 70 80 90 100
0 1 2 3 4 5 6
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Bradawl
(or sharp point)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Ruler - Use this ruler to help correctly identify the screws
ABC
DEF
GHI
JKL
14mm Screw x 17
Shelf support x 4
O
30mm Dowel x 4
50mm Screw x 4 39mm Locking pin x 2
30mm Screw x 4
15mm Screw x 16
(This screw is included in
the door hing bag)
Door hinge x 4
Nail x 20
Support cover x 4 Handle x 2
Wall plug x 1
MN
P
Front castor x 2 Castor x 2
Wall strap x 1
(This screw is
included in the
wall strap bag)
x 1

4
Assembly Instructions
Step 1
b:
Door hinges ‘back
plates’onto the Left side
panel and Right side
panel .
B
A
Attaching hinges
A
B
B
A
Step 2
a: F
F
H
H
2
1
3
3
1
2
a: Screw Locking pins
into the Top panel .
Attaching top panel
F
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
3
Use a screwdriver to turn
Locking nuts clockwise
to lock.
3
1
2
Finished
front edge
Finished
front edge
1
2
Finished
front edge
Finished
front edge
b:
H
Carefully place the Top
panel onto the unit.
Insert 2 Locking nuts
into the Left side panel
and Right side panel .
H
A
B
A
BG
G
G
G
G
Insert Dowels into the
Left side panel and
Right side panel .
1
2
F
A
B
H

Step 3
Assembly Instructions
5
Step 4
Step 5
5
5
E
E
E
E
Attaching bottom
panel
Finished
front edge
Bottom panel onto the
unit.
E
Note: The Front castors
feature a locking arm.
We recommend you lock
the castors when you have
in place.
Fixing castors
M
Front castors and
Castors onto the unit.
C
M
N
Fixing back panel
7
Back panel onto the
unit.
L
Important:
The cabinet MUST
be ‘square’ when the
back is attached.
C
C
C
C
M
N
M
N
1
2
f
7
Finished
ront edge
back surface
L
5
5
2

Step 6
Assembly Instructions
Step 7
Attaching door hinges
Attach Handles to the
outside of the Doors
using Screws .
D
K
4
6
a: Bb:
B
Hanging doors
Fix 2 Door hinges to each
Doors using Screws .
B
4
A
a:
With help, slot Door
hinges onto ‘hinge plates’.
B
b:
Tighten screw shown to
lock hinges in position.
See ‘Hinge adjustment’
in step 9 if the doors need
adjusting.
Repeat a and b for
opposite door.
X 2
K
A
B
4
4
B
B
B
B
K
D
D
D
D
4
B
A
A
B
c:
K
D
D
c:

Step 8
Assembly Instructions
b:
Slide the Shelf into
the unit.
6
a:
b:
Attaching shelf
a:
SIide Support covers
onto Shelf supports .
lnsert Shelf supports
(Support covers are
included) into the unit.
before inserting the Shelf.
JI
I
Note:
Set the shelf
supports to the desired
height.
J
6
7
JI
J+I
Finished
front edge

Step 9
Assembly Instructions
b:
To move doors in or out:
loosen screw shown and
move doors to suit.
Re-tighten screws.
c:
To move doors left or
right: loosen screw shown
and move doors to suit.
Re-tighten screws.
a:
b:
c:
8
Hinge adjustment
a:
To move doors up or
down: loosen screws
shown and move doors to
suit.
once doors are aligned,
re-tighten Screws .
A
b:
Door
c:
Door
a:
Door
A

Step 10
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Assembly is complete.
With help, move storage
cupboard into position.
remove storage cupboard.
Drill a hole and insert Wall
plug .
Reposition storage cupboard
Screw .
Fixing to wall
Warning:
The sotrage
cupboard is heavy.
Lift with care.
Warning:
Before drilling,
check wall for
hidden pipes and
cables.
9
O
P
wall
C
P
Top panel
O
P
PPO
Note: Wall plugs supplied are
for solid wall only.
be used for your wall, seek
professional advice if in doubt
It is recommended that the
a wall.
top panel using Screws .
P
Fix Wall strap to back of
C

A Guide to - Wall Mounting & Fixings
Revision 2 - 7/10/09
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5:
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
responsibility of the installer.