Argos Winchester 408/5571 User manual

MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Winchester - Coffee Table
Assembly Instructions - Please keep for future reference
ALR3164
408/5571
Width - 99.6cm
Depth - 49.5cm
Height - 46.6cm
Issue 1 - 15/07/15

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 29kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
2
80%
12 3
4
Left Side (DF2796)
(44.4 x 45.5cm)
Divider (DF2799)
(19.8 x 45.1cm)
Shelf (DF2798)
(92.6 x 45.3cm)
Right Side (DF2797)
(44.4 x 45.5cm)
Top (DF3356)
(99.6 x 49.5cm)
Rail (DF2791)
(92.6 x 9cm) x 4
Side Plinth (DF2800)
(45.5 x 9.1cm) x 2
Back (DF2801)
(45.55 x 19.8cm) x 2
Front Plinth (DF2792)
(98.8 x 9.2cm) x 2
Drawer Front (DF2787)
(44.9 x 19cm) x 2
Drawer Back
(W370-124)
(42.3 x 12.4cm) x 2
Drawer Base (T434-367)
(43.4 x 36.7cm) x 2
Left Drawer
Side (W370-124LH)
(37 x 12.4cm) x 2
Right Drawer
Side (W370-124RH)
(37 x 12.4cm) x 2
5
6 7
8 9 10
11 12 13
14

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D F
G H I
L
N
Small locking
nut (F3) x 4
C
M
J K
Drawer runner (F1004) x 4
Large locking
nut (F900) x 22
Metal dowel (F901) x 26
Wooden dowel (F22) x 26
25mm Screw (F50) x 8 9mm Screw (F74) x 4
9mm Screw (F73) x 8 Plastic Nail (F91) x 4
Wedgefix (F639) x 4
Knock-in Peg (F171GY) x 8
E
Handle
(F463) x 2
38mm Screw (F81) x 2
Large wooden dowel (F40) x 2
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver

10
Assembly Instructions
4
Step 1
x 2
x 2
80%
x 2
x 2
x 2
A
A
C
C
C
C
11 12
Step 2
Prepare the 2 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
10
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
11
12
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
11
12
10
C
C
11
12
11
12
A
A
10

10
Assembly Instructions
5
Step 4
K
K
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
14
11 12
10
13
11 12
14
13
13
K
Attach the handles
Attach a handle to
each of the drawer fronts
. using screw .
Note: Do not
overtighten the screw.
N
G
10
11 12
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
F
x 2
x 2
x 2
K
K
x 2
F
F
F
14
11
13
11
12
14
12
G
N
10

D
D
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 8
Prepare the left side
a: Place a runner on
the left side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Screw 6 metal
dowels into the left
side .
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into the left side . .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
1
J
J
B
1
1
M
M
A
1
D
1
a:
b:
c:
J
M
J
M
J
A
A
A
A
B
B
A
10mm
D
1
1
1
B
A

D
D
Assembly Instructions
7
Step 9
Prepare the right side
a: Place a runner on
the right side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
c: Screw 6 metal
dowels into the right
side .
Insert 2 large locking
nuts into the right
side .
Tap 2 wooden dowels
into the right side .
2
J
J
B
2
2
M
M
A
2
a:
b:
c:
D
2
J
M
J
J
B
A
A
A
A
A
B
A
Finished
front edge
Finished
front edge
Finished
front edge
2
2
2
M

Assembly Instructions
8
Step 10
D
D
B
B
D
Prepare the shelf
Screw 2 metal dowels
into the shelf .
Insert 4 large locking
nuts into the shelf . .
Tap 4 wooden dowels
into the shelf . .
5
B5
D
B
B
D
A
A
A
5
5
Step 11
A
B
2
Fit the shelf
Push the shelf onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
2
5
B
5
5
B

Turn the
divider over
D
D
Assembly Instructions
9
Step 12
Prepare the divider
a: Place a runner on
the divider as shown.
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the divider .
Tap 2 wooden dowels
into the divider .
Turn the divider over
c: Place a runner on
the divider as shown.
Slide back the top of
runner and use the 2nd
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the divider .
Insert 2 large locking
nuts into the divider .
3
J
J
3
M
M
3
J
J
3
M
M
D
3
a:
c:
d:
b:
J
M
J
M
J
J
M
J
B
B
B3
Note: Due to the manufacturing
process, the 2 holes for the
large locking nut can be on
either surface of the divider.
J
M
Note: The 2 large locking nuts can
be on either surface of the divider.
Fit the divider
Push the divider onto
the shelf .
Use a screwdriver to
tighten the large locking
nut fitted to the
divider .
5
3
B
3
5
3
Step 13
3
3
3
3