Argos Jenson 937/8032 User manual

Spare Parts
Visit: www.argos-support.co.uk
Email: [email protected]
Call: 0330 016 1114
Customer Support
Call: 0345 640 2020
JENSON
Gloss
937/8032 922/8058
Issue 1 - 11/12/20

Safety
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 56kgs.
Please lift with care.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions -
otherwise a safety risk can
occur if incorrectly installed.
• Do not use this item if any
components are missing or
damaged.
Care Advice
• Check you have all the
components and tools listed on
relevant pages.
• Remove all fittings from the
specified plastic bag and
separate them into their groups.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall using
the 2 overbalance protector kits
supplied.
• A unit that is allowed to topple
can cause serious or fatal injury.
In addition to wall fixing the unit,
place heavy items on the lower
shelves, do not put any heavy
objects on top of the unit and
never allow children to climb or
hang on drawers, doors or
shelves.
• Refer to guide after section 31
for wall fixing information.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Assembly videos are
available throughout
these instructions by
scanning in the QR
codes.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean with a damp cloth.

Cabinet Panels Please do NOT remove any protective film until after assembly
548.2 x 6.0cm x 4
DF-00023784
967.7 x 49.3cm x 2
XDF-00023780
12 48.2 x 39.6cm x 2
DF-00023785
13 47.1 x 39.6cm
DF-00023781
14 63.7 x 49.5cm x 3
DF-00023778
10 67.7 x 48.3cm
XDF-00023791
11 149.9 x 45.0cm
DF-00023783
847.1 x 6.0cm x 2
DF-00023782
747.1 x 41.4cm
DF-00023777
673.3 x 41.5cm
DF-00023789
273.3 x 42.9cm
DF-00023253
373.3 x 41.5cm
DF-00023787
448.2 x 41.4cm x 2
DF-00023786
173.3 x 42.9cm
DF-00023252

Fittings Use these drawings to
correctly identify the fittings
Main Bag
F22
Cx 22
F137
Jx 4
F901
Bx 16
Kx 8
F646
F639
Ix 10
F900
Ax 32
F110
Hx 12
F40
Ex 10
F566
Dx 8 Fx 13 Gx 4
F276
F63
Lx 12
Mx 2 Nx 6
F277
Tools
Only used for
drilling walls
F474
F328

1
2
1
Cx 6
Finished
front edges
1
2
2
Ax 4
Main Bag
F22
Cx 22
F137
Jx 4
F901
Bx 16
Kx 8
F646
F639
Ix 10
F900
Ax 32
F110
Hx 12
F40
Ex 10
F566
Dx 8 Fx 13 Gx 4
F276
F63
Lx 12
F277

1
2
4
Ax 2 Cx 3
5
3
Ax 4 Cx 3
Finished
front edge
Finished
front edge
3
Bx 8
4

1
4
6
7
Ax 4 Cx 2
5
5
Finished
front edge
Finished
front edge
x 2

8
9
D
F
Ex 5
Finished
front edge
4
3
5
5
x 2

6
10
11
Ax 2 Cx 3
Finished
front edge
x 2
x 2
3
x 4
D

12
13
Finished
front edge
Ax 4
7
7
3
Finished
front edge x 2

8
8
14
Ax 4
8
8
15
x 2

16
Ex 5
Finished
front edge
17
6
6
x 2
x 2
x 4
D

18
4
Ax 4 Cx 3
Finished
front edge
4
Finished
front edge
x 2
19

20
21
Ax 4 Cx 2
5
5
5
5
x 2

22
23
x 8
K
2
Finished
front edge
x 2
x 2

24
25
www.youtube.com/watch?v=FeaI6541z7o
Squaring up a Chest and fitting the Back Panels
A = B
Make sure measurements
are the same.
The Back panels must be
flush with the Back Rail.
9
9
10
AA
A
B

10
9
9
26
x 9
F
10
9
9
27
Gx 4
Fx 4
IMPORTANT:
You will need to keep 4
nails for the next step

29
IMPORTANT:
The Back panel must
slot into the groove
in the Top panel
11
11
28
Bx 8 Mx 2
Finished
front edge
Finished
front edge
Only use 1 Screw
to fit each Bracket

30 Ix 10

31
Top
WARNING!
In order to prevent overturning
this product must be used with the 2
wall attachment devices provided
Slide the Brackets against the wall. Fit the 2nd screws supplied
with the Brackets into the underside of the Top panel.
Mark the slot at the back of the Brackets for drilling into the wall.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill
into any pipes, wires etc.
If in doubt, consult an expert.
See the next section for a guide
to wall mounting and fixings