Argos Hygena Genoa 481/2380D User manual

Hygena Genoa Slatted Sideboard
Dimensions
Width - 120cm
Depth - 40cm
Height - 69cm
Issue 1 - 16/09/15
Important –Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Assembly Instructions- Please keep for future reference 481/2380D

1
Note: if require the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Remove all fittings from the
plastic bags and separate them
into their groups.
Safety and Care Advice
Important– Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 & 3.
• Keep children and animals
• Make sure you have enough
space to layout the parts before
starting.
away from the work area, small
parts could choke if swallowed.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance

2
Components- Panels
Please check you have all the panels listed below
Bottom panel
(1200 x 390 mm)
Foot x 5
(60 x 60 mm) (1200 x 390mm)
123Top panel
Left side panel
(524 x 389mm)
Right side panel
(524 x 389mm) (524 x 325mm)
456Divider
Rear panel
(1186 x 548mm)
Adjustable shelf x 4
(573 x 320mm) (578 x 518mm)
7
Left side door
(587 x 518mm)
10 Right side door rail
(518 x 61mm)
11
89Right side door

3
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Components- FittingsIf you have damaged or missing components,
call the Customer Helpline: 03456 400800
Please check you have all the fittings listed below
50mm Screw
x
x
5
A
B C
14 mm Screw x 20
D
E
Metal cam x 6
F
Shelf pin
x
16
Ruler- Use this ruler to help correctly identifythescrews
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
105
Metal dowel
x
6
G
H I
J
Tools required
Phillips screwdriver
(medium & small)
Flatblade screwdriver
Small wood dowel x 12Cover pad x 9
40mm Screw
6
x
25mm Screw
3
Large wood dowel x 10

4
Assembly Instructions
Step
1
Lay Bottom Panel on
its long taped edge on a
flat soft surface.
Push Legs onto the
wood dowels in Bottom
panels and fasten using
50mm Screws .
Step
2
1
2
B
Lay Side Panels
and Divider on their
taped edges on a flat
soft surface.
Push Wood dowels
into ends of side
panels and .
Push Bottom panel
onto the wood dowels in
the end of panels and
fasten using 40mm
Screws .
4
6
45
1
5
6
H
I
1
2
Untaped edge.
A
B
1
6
5
4
Untaped edge.
Untaped edge. Untaped edge.
Untaped edge.
H
I
Push Large wood dowels
into indicated holes in
Bottom panel.
A

5
Assembly Instructions
Step
3
Step
5
Screw 6 Metal dowels
into the threaded holes in
Top Panel as
shown.
C
3
Insert the 6 Metal Cams
into the 6 holes on
the Panels so
that they are flush.
Note: Longer
leg of the cross
on the Metal
Cams must face towards
end of panel (as shown).
Then, using a Philips
Screwdriver, screw all 6
Metal Cams
clockwise until they are
‘hand tight’.
D
654
D
Step 4
3
C
3
6
4
5
Untaped edge.
I
dowels and wood
dowels enter
corresponding holes.
C
A
Insert Small wood dowels
into the middle holes in
Side panels and Divider.
I
Firmly push the Top
Panel onto the ends
of the panels and
, ensuring the Metal
dowels and wood
dowels enter
corresponding holes.
C
3
6
4 5
I
Turn the unit upright,
cover all visible cam
holes with Cover pads .
D
G
Note: Longer leg of
the cross on the
Metal Cams must
face towards end
of panel.

Tape.
6
Step
6
Step
7
Unfold Rear Panel .
Secure the Rear Panel
into the rear edges
of side panels, top panel
and bottom panel
using 14mm Screws .
Note - make sure
cabinet is square
before securing
rear panel in place.
7
7
7
F
F
Assembly Instructions
8
Taped edge.
E
Push 4 Shelf Pins
into each side of the
side panels and divider
at desired height.
E
Place adjustable
shelves onto the
Shelf Pins.
8
Measure on the back
across the 2 diagonals
to make sure cabinet is
square.
Y
X

Insert the bottom rollers
of Door in the inner
groove in the bottom
panel, holding the door
and push the top edge to
line up with the inner
groove in top panel.
Push the release button
to release the pin into the
top inner groove.
7
Step
8
Make sure the pin in the
top lock in the Door
is down, if not, push it
down until it locks.
9
9
Secure Right side door
rail on to the Right
side door using
Screws from the
counter sunk hole as
shown.
Cover the visible screw
holes with Cover pads .
Insert the bottom rollers
of Door in the outer
groove in the bottom
panel, holding the door
and push the top edge
to line up with the outer
groove in top panel.
Push the release button
to release the pin into the
top outer groove.
Make sure the pin in the
top lock in Left side
door is down, if not,
push it down until it locks.
10
10
11
11
Pin 2 people needed for this step.
If you need help or have damaged or missing parts, call the Customer Help Line: 03456 400800
Home Retail Group plc. Avebury, 489-499 Avebury Boulevard. Milton Keynes. MK9 2NW
Assembly Instructions
J
J
G
Step 9
Step 10
9
9
Assembly is complete.
Release button