Argos 642/0110 User manual

Impressions - Overbed Unit
642/0110
Assembly Instructions - Please keep for future reference
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call Customer Helpline 0844 880 6770
Dimensions
Width - 228cms
Depth - 41.5cms
Height - 51.5cms
642/1841
KA5882/02

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
2
• Check you have all the
components and tools listed on
pages 2, 3 and 4.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Tools required
Cross slot screwdriver
Hammer
Bradawl
Tape measure
5mm
DRILL BIT
The next page can be cut out and used as reference throughout the assembly.
Keep this page with these instructions for future reference.

Components - Panels - Exploded Veiw
Please check you have all the panels listed below
3
Components - Fittings
Please check you have all the fittings listed below
If you have damaged or missing components,
call the Customer Helpline 0844 880 6770
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may
be supplied than are required.
Plan view of panels on page 4
Panel pins x 50
E
Half cranked hinge x 12
F
Angle bracket x 6
D
15mm Screw x 30
C
Metal cam x 36
A
Metal Dowel x 36
B
Hinge plate x 12
G
Connector bolt x 8
I
25mm Screw x 6
H
96mm Handle x 6
J
19mm Bolt x 12
K
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 5550 60 65 70 75 80 85 100 10590 95 110 115 120 125 130 135 140 145 150 155 160 165 170
11
1
1
1
1
2
2
2
2
2
2
3
3
3
3
3
3
4
4
4
5
5
5
5
5
6
6
6
5

Components - Panels - Plan Veiw
Please check you have all the panels listed below
4
Side (50 x 40 cm) x 6
Top/base (73 x 39.6cm) x 6
Corniche/Batton (76 x 8 cm) x 6
Shelf (73 x 28 cm) x 3
Door (49.5 x 37 cm) x 6
Back (74.8 x 49.5 cm) x 3
1
2
3
4
5
6

Front edge
Assembly Instructions
Step 1
5
Fitting metal dowels
Screw metal dowels
into panel
Note: Insert metal dowels as
far as shown.
Repeat for the other five panels
Do not over tighten.
Fitting hinge plates
Screw hinge plates into
panel
Note: Unscrew centre screw
on hinge plate before attaching
to panel (see illustration)
Repeat for the other five panels
Do not over tighten
Do not use power/electric screw drivers to attach the hinge plates.
Please use a normal screw driver to attach it gently as shown here.
DO NOT OVERTIGHTEN THE SCREWS AS IT WILL STRIP OUT THE HOLES.
Step 2
Long leg
forwards
Front
edge
1
G
X 6
X 6
X 3
Fitting metal cams
Press metal cams firmly
into holes in the top/base
Repeat for the other five
panels.
Press metal cams firmly
into holes in the shelf
Repeat for the other two panels.
G
G
GG
B
B
1
G
1
B
B
B
B
BB
G
1
2
A
A
A
A
4
A
A
A
A
2
4
A
A

Assembly Instructions
Step 3
6
Step 4
Cam lock in open
position
Cam lock in closed
position
Attaching panels
Position top/base and side
secure by turning cam
locks clockwise
Do not over tighten.
Position shelf onto
side and by turning cam
locks clockwise
Do not over tighten.
Note:
Repeat above to make two
further sections.
X 3
Attaching panels
Position top/base and side
secure by turning cam
locks clockwise
Do not over tighten.
Note:
Repeat the process on the
other two sections.
X 3
1
4
2
A
A
A
A
2
1
A
1
4
A
1
4
2
2
A
A
2
1
A

Assembly Instructions
Step 5
7
Important note:
Two people required to
turn unit over
Square up unit
Using a tape measure,
ensure the distance from top
left corner to bottom right
corner is equal to the
distance from top right corner
to bottom left corner
Note:
Repeat the process on the
other two sections.
Attaching panels
Position side to top ,
base and shelf secure
by turning cam locks
clockwise
Do not over tighten.
Note:
Repeat the process on the
other two sections.
X 3
Step 6
A to B = C to D
X 3
Back of unit
Front
edge
Attaching back panels
Position back panel onto
the back of the unit and secure
using panel pins
Note:
Repeat the process on the
other two sections.
E
6
E
6
X 3
A
A
A
A
A
A
1
4
2
2
1
1 2
A
2 4
E
E
6
E
1
21
6

Assembly Instructions
Step 7
8
Step 8
Attaching to the wall
Mark the wall so the top
lines up with the underneath
of the top of the adjoining
robe. (see illustration)
2
C
D
Important note:
It is essential that this
product is fixed to a wall
using the bracket
supplied
Fixing Safety brackets
Postion safety brackets
as shown on the back
edge of the top secure
using screws
Note:
Repeat the process on the
other two sections.
X 3
Mark wall at correct height
2
CC
1
2
1
2
4
2
C
D
D
D
2
2
4

Assembly Instructions
Step 9
9
Step 10
Attaching panels
Secure the reamining cabinets
and robe by the same method
as in step 9 using connecting
bolts
Do not over tighten.
DO FIRST
DO SECOND
Important note:
To join the robes
together, carefully drill
through the holes as
shown. It is best joining
together in position,
before attaching to a
wall.
Connecting to another robe
Drill though the holes in unit
sides using a 5mm drill bit.
(see illustration)
Position units together and
screw together using
connecting bolts
(see illustration)
Connect to the end unit
as in stage 9
Connect to the next 2
cabinets as in step 9
I
2
I
I

Assembly Instructions
Step 11
10
Step 12
Attaching panels
Secure battons to the wall
beneath each cabinet using
suitable wall fixing
(Wall fixings not supplied)
Do not over tighten.
For additional support attach
the battens to the wall
beneath the cabinets
(Wall fixings not supplied)
Attaching door hinges
Attach hinges to doors
using 15mm screws
(see illustration)
Repeat for the other five doors
BACK OF
DOOR
X 6
3
3
3 3 3
5
F
C
F
CF
C
5
F
C
5