Argos Adult Malibu User manual

MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
531/3637
544/0366
555/8722
557/1730
555/3057
Adult Malibu - 3+2 Wardrobe
Assembly Instructions - Please keep for future reference 553/2724
543/5041
560/9712
558/3924
555/9518
Width - 74.8cm
Depth - 49.8cm
Height - 180.5cm
Issue 1 - 18/05/16
CR
CR
CR
More help is available throughout this booklet by scanning
in the QR codes or typing in the links

Rule
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Step
ladder
Electric drill
(only use
when drilling
into walls)
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 50kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1 to 4.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: To prevent
possible overbalancing this unit
must be secured to a wall
using the overbalance protector
kit supplied or, an alternative
fixing method of your choice.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below When applicable, remove any
protective film before use
2
Horizontal (DF5862)
(71.4 x 47.2cm)
Left Side (DF6010)
(179 x 49.6cm)
Right Side (DF6011)
(179 x 49.6cm)
Top (DF6014)
(74.8 x 49.8cm)
Drawer Front (DF5996)
(70.8 x 15.7cm) x 3
Drawer Back (W665-130)
(66.5 x 13cm) x 3
Left Drawer Side
(WB450-130LH)
(45 x 13cm) x 3
Left Door (DF6012)
(119.6 x 35.25cm)
Right Drawer Side
(WB450-130RH)
(45 x 13cm) x 3
Drawer Base (T676-447)
(67.6 x 44.7cm) x 3
Right Door (DF6013)
(119.6 x 35.25cm)
1 2
4
3
Hanging Rail (FHR708)
(70.8cm long)
5
Plinth (DF5856)
(71.4 x 9.2cm) x 2
Cross Rail (DF5858)
(71.4 x 6cm) x 2
Back Rail (DF5866)
(71.4 x 9.2cm)
6
7
8
9 10 11 12
13
14 15
Back (X1709-740)
(170.9 x 74cm)
16

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
3
Drawer Fittings Bag marked ‘drw kit’
A
Quickfit dowel (F545) x 6
C
Knock-in Peg (F171GY) x 12
D E
19mm Screw (F461) x 6
Large locking cam nut (F607) x 6
B
13mm Screw (F79) x 6 13mm Screw (F63) x 12
F
HG
9mm Screw (F73) x 18
Main Fittings Bag
A
Quickfit dowel (F545) x 14
D
19mm Screw (F461) x 2
M
Wooden dowel (F22) x 26
I
Nail (F51) x 34
J
B
Small locking cam nut (F607) x 14
K
Rail Holder (F891) x 2
L
Plastic Nail (F91) x 5
F
13mm Screw (F63) x 6
Door Buffer (F137) x 4
13mm Screw (F52) x 4

Components - Fittings
4
Individual Fittings Bags
P
O
Handle (F418) x 8
Pre-mounted
hinge (F419) x 6
436mm long
Drawer Brace (F427) x 3
Q
M
RCR Runner (F609) x 3
b
DL Runner (F610) x 3
Rc
CL Runner (F608) x 3
Ra
DR Runner (F611) x 3
Rd
450mm long
CR
CL
DR
DL
Overbalance protector
kit (F474) x 1
N

5
Step 1
Assembly Instructions
Step 2
Fit the drawer sides
to the 3 drawer fronts
Push the left drawer
sides . and right
drawer sides . down
onto the back of the 3
drawer fronts .
Turn the large locking
cam nuts clockwise
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
11
9
12
Prepare the drawer
sides
a: Insert a large locking
cam nut into the left
drawer sides and the
right drawer sides .
Note: The arrow on the
locking cam nut must
point towards the
hole in the end of the
panel.
b: Push 1 of the quickfit
dowels as far as it will
go into the 6 left drawer
sides and the 6 right
drawer sides .
Note: Only the plastic
thread of the quickfit
dowel sticks out from the
panel.
A
11
12
B
11
12
x 3
11 9
12
B
B
a:
b:
B
x 3 x 3
11 12
BB
A
x 3 x 3
11 12
AA
Use the Drawer Fittings Bag marked ‘drw kit’ for Steps 1 - 7
hps://www.youtube.com/watch?v=HclfJdkm-Lg
Standard Drawer Box Assembly

Assembly Instructions
6
Step 3
Fit the drawer bases
Slide a drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 4
Fit the drawer backs
Fit a drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
13
1211
9
10
11 12
13
10
10
C
11 12
x 3
x 3
x 3
Step 5
Fit the handles
Attach 2 handles to
each drawer front
using screws .
O
D
9
D
O
D
O
9
9
12
11
13
12
13
C
C
11
C
C
10

7
Step 6
Assembly Instructions
x 3
Fit the drawer braces
Turn the 3 drawer
assemblies over and
hook a drawer brace
onto the bottom edge of
the drawer back .
Fix it to the drawer front
and drawer back using 2
screws .
Q
E
Q
E
Q
E
E
E
Q
x 3
R d
Fit runners to the
drawers
Fit the DL runner to
the bottom edge of the
left drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit the DR runner to
the bottom edge of the
right drawer side
using the same method.
12
R c
11
9
F
R d
DR
Step 7
12
11
9
DL
F
F
F
F
R c
DL
10
10
Runners must be
pushed up against
the drawer front
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounter Runners

Finished
front edge
Finished
front edge
M
M
AM
A
Finished
front edge
Assembly Instructions
8
Step 8
Prepare the left side
a: Fit 3 CL runners
to the left side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
Fit a rail holder , to the
left side using 2
screws .
c: Insert 2 large locking
cam nuts into the left
side .
Push 2 of the quickfit
dowels as far as they
will go into the left side
. .
Tap 3 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
R a
1
H
H
F
B
1
1
R a a:
b:
c:
A
M
1
K
G
1
R a
H
1st
screw
Finished
front edge
CL
Finished
front edge
F
CL
H
R a
H
H
CL
H
R a
H
H
CL
H
R a
H
H
CL
F
CL
F
CL
F
G
G
K
B
10mm
M
A
B
CL
CL
CL
1
1
1
B
Use the Main Fittings Bag for Steps 8 - end
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounter Runners

M
M
AM
A
9
Step 9
Assembly Instructions
Prepare the right side
a: Fit 3 CR runners
to the right side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
Fit a rail holder , to the
right side using 2
screws .
c: Insert 2 large locking
cam nuts into the
right side .
Push 2 of the quickfit
dowels as far as they
will go into the right side
. .
Tap 3 wooden dowels
into the right side .
R b
2
H
H
F
B
2
2
R b
A
M
2
a:
b:
c:
R b
H
1st
screw
Finished
front edge
CR
Finished
front edge
F
CR
F
CR
F
CR
F
CR
H
R b
H
H
CR
H
R b
H
H
CR
H
R b
H
H
CR
CR
CR
B
B
Finished
front edge
2
Finished
front edge
2
Finished
front edge
2
A
B
G
G
K
K
G
2

M
M
Finished
front edge
Finished
front edge
M
M
A
A
M
Assembly Instructions
10
Step 10
Prepare the horizontal
Insert 4 large locking
cam nuts into the
horizontal .
Push 4 of the quickfit
dowels as far as they
will go into the horizontal
. .
Tap 6 wooden dowels
into the horizontal .
A
4
4
4
B
Finished
front edge
B
B
B
A
M
M
A
M
4
Fit the horizontal to
the right side
Push the horizontal
onto the right side .
Turn the 2 large locking
cam nuts clockwise
as far as it will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
4
2
CR
CR
CR
M
B
4
2
Step 11
Note: The cross rails have no
holes drilled on either surface
M
M
Prepare the 2 cross
rails
Tap 4 wooden dowels
into each of the 2 cross
rails .
M
7
Step 12
7
Finished
front edge
x 2
B
hps://www.youtube.com/watch?v=9C7tgv5xnbE
Carcase Assembly

Finished
front edge
11
Step 13
Assembly Instructions
CR
CR
CR
2
7
Finished
front edge
7
Fit the 2 cross rails to
the right side
Push the 2 cross rails
onto the right side as
shown.
7
2
Step 14
Prepare the 2 plinths
and the back rail
Insert 2 large locking
cam nuts into the
each of the 2 plinths
and the back rail . .
Push 2 of the quickfit
dowels as far as they
will go into the each of
the 2 plinths and the
back rail . .
Tap 2 wooden dowels
into the each of the 2
plinths and the back
rail . .
A
6
8
6
8
6
8
B
M
A
M
A
M
6
A
M
A
M
8
Finished
top edge
Note: The 2 plinths and the
back rail are similar but, the
back rail has a finished top edge
x 2
B
B
B
B

Finished
front edge
Note: Support these 2 panels until
the left side is fitted in the next step
Assembly Instructions
12
Step 15
Step 16
CR
CR
CR
2
6
Finished
top edge
6
8
CR
CR
CR
Fit the 2 plinths
and the back rail
Push the 2 plinths
and the back rail
onto the right side .
Turn the 3 large locking
cam nuts clockwise
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
6
8
2
CR
CR
CR
Fit the left side
Push the left side
onto the assembly.
Turn the 5 large locking
cam nuts clockwise
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
1
1
B
B

Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Finished
front edge
13
Step 17
Assembly Instructions
CR
CR
CR
CR
CR
CR
Fit the top
Push the top onto
the assembly.
Turn the 4 large locking
cam nuts clockwise
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
3
3
Step 18
16
I
16
yy
y
y
x
x
CR
CR
CR
CR
CR
CR
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
x
x
17
16
B
b:
I
16
www.youtube.com/watch?v=udEKmXmPEW0
Squaring up a Robe and tting the Back Panel

CR
CR
CR
CR
CR
CR
17
Assembly Instructions
14
Step 19
Fit the 5 plastic nails
Tap 2 plastic nails
into the bottom edge of
each side and .
Tap the remaining plastic
nail into the bottom
edge of the plinth at
the front of the unit.
Carefully stand the
unit up for the next
step and place it in its
final position in the
room.
J
J
1
6
2
Warning: The
unit is heavy.
Lift with care.
J
J
J
1
2
6
J
J

15
Step 20
Assembly Instructions
Fit the overbalance
protector kit
a: Before fitting the
overbalance protector
kit, use a spirit level to
check the base (or top)
of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level.
a: To prevent possible
overbalancing this unit
must be secured to a
suitable wall by fitting of
the overbalance
protector kit to the
unit, or an alternative
fixing method of your
choice.
Wall fixings are not
supplied as they will
need to suit the wall
type.
Note: Take care when
drilling the wall that you
do not drill into any
pipes, wires etc.
If in doubt, consult an
expert.
N
a:
b:
CR
CR
CR
N
N

Assembly Instructions
16
Step 21
CR
CR
CR
Fit the hanging rail
and drawers
Push the hanging rail
into the rail holders
fitted to the side panels.
Slide the wheels of the
runners fitted to the
drawers, over the wheels
of the runners fitted to
the side panels and push
the drawers into position.
Side
panel
Drawer
5
5
K
5
K
Step 22
L
14
15
Prepare the 2 doors
Push fit 3 hinges into
each door and .
Secure each hinge by
tighteng up its 2 screws.
P
14 15
P
P
P
P
P
P
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounter Runners
hps://www.youtube.com/watch?v=b4NeCGnpjP8
Pre-mounted Hinge Fitting & Adjustment

17
Step 23
Assembly Instructions
O
Fit the doors and the
handles
2 people are needed
here
Fit 1 door and at
a time, by lining up the 2
screws in the top hinge
with the 2 holes at the
top of the panel and
push them in.
Working down the door,
push in the other hinges.
When all of the hinges
have been pushed into
place, tighten the 2
screws on each hinge.
Attach a handle to
each door using screw
. .
Press the screws into
the holes in the panels
When the hinges have
been pushed in,
tighten up their screws
P
P
Warning: The
doors are heavy.
Lift with care.
P
O
D
14 15
CR
CR
CR
Note: Fit the
top hinge 1st
15
D
14
O
hps://www.youtube.com/watch?v=b4NeCGnpjP8
Pre-mounted Hinge Fitting & Adjustment

Assembly Instructions
18
Step 24
b:
c:
d:
a:
A
A
B
C
Adjust the doors if
needed
a: Before adjusting the
doors, use a spirit level
to check the base (or
top) of the unit is level,
front-to-back and
side-to-side in the 3
positions shown.
Use suitable packing
pieces (not supplied) to
make the unit level
BEFORE making any
adjustment to the hinges,
as shown.
b: Height adjustment.
Loosen screws A on
hinge plates and move
door up or down as
required.
Retighten screw A.
c: Forward and Back
adjustment.
Loosen screw B on hinge
plate and move door in
or out as required.
Retighten screw B.
d: Sideways
adjustment.
To move door ‘out’
loosen screw C.
To move door ‘in’ tighten
screw C.
hps://www.youtube.com/watch?v=b4NeCGnpjP8
Pre-mounted Hinge Fitting & Adjustment