Argos Haversham 376/6066 User manual

Haversham - Dining Table
376/6066
Assembly Instructions
- Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Important – Please read these instructions fully before starting assembly
Dimensions
Width - 150cm
Depth - 80cm
Height - 78cm
Issue 1 - 12/11/14

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
. Check you have all the
components and tools listed on
pages 2 and 3.
. Remove all fittings from the
plastic bags and separate them
into their groups.
. Keep children and animals
away from the work area, small
parts could choke if swallowed.
. Make sure you have enough
space to layout the parts before
starting.
. Do not stand or put weight on
the product, this could cause
damage.
. Assemble the item as close
to its final position (in the same
room) as possible.
. Assemble on a soft level
surface to avoid damaging the
unit or your floor.
. We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
. Parts of the assembly will be
easier with 2 people.
. Dispose of all packaging
carefully and responsibly.
This product contain
Natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
.
Care and maintenance
.
. Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
. From time to time check
that there are no loose
screws on this unit.
. This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
2
02 Leg x 4 (76,2 x 6cm)
01 Top panel (150 x 80cm)

Soft close hinge X 06
3
2m
Components - Fittings
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
If you have damaged or missing components,
call the Customer Helpline: 03456 400 800
AA
A
D
H
Top panel clip X 4
ABC
3,5 x 16mm Screw X 24
EF
G
Top panel hinge X 4
Allen key X 1 1/4x40mmBolt X8 Foot pad 4 X
3,0 x 16mm Screw X 16

Assembly InstructionsAssembly Instructions
Step 2
Step 1
Assembly Instructions
4
Fix legs to the table top
using bolts and
allen key .
With the help of a hammer,
fix foot pads as shown.
Turn the table upright.
B
A
C
01
02
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
01
02
C
CC
C
02
02
02
Caution!
Carefully place the
top panel sideway
on a soft and clean surface
to avoid damaging the
01
With help, insert legs
into top panel through
02
joints, as shown.
B
B
AA
C
4x
02
4x
product.

Assembly InstructionsAssembly Instructions
Step 4
Step 3
Assembly Instructions
5
Fix four top panel hinges
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Assemble is complete
Caution!
Two people are
required for Steps
and .
03
With help, open the
compartment and fix soft
closing hinges using
F
D
D
D
D
6x
E
H
4x
E
E
G
4x
E
04
F
D
screws into pre drilled
G
into pre drilled holes using
screws as shown. Make
E
sure they are positioned
correctly.
Fix four top panel clips H
using screws into pre
drilled holes as shown.
E
holes as shown.
First, fix hinges at the
interior of table (number 1),
then, force the other side of
hinge down in order to fix
numbers 2 and 3 in the pre-
drilled holes.
Make sure to fix screws
folowing the order as
shown in the picture (1-2-3).
1-
2-
3-
1-
Before closing the top, make
H
sure clips are centralized
in hinges . If not, unscrew
G
screws and move clip
left or right.
H
E