Argos Montana 397/6571 User manual

MADE IN
BRITAIN
Dimensions
Width - 120cm
Depth - 40cm
Height - 58cm
Montana - 2 Door Large TV Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 13/04/15
Important - Please read these instructions fully before starting assembly
ALR3150
397/6571
391/0441

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 30kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
12 3
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
5
Left End (DF3502)
(522 x 378mm)
Right End (DF3503)
(522 x 378mm)
Top (DF3493)
(1200 x 396mm)
Base (DF3494)
(1200 x 396mm)
End Shelf (DF3497)
(368 x 370mm) x 2
Middle Shelf (DF3501)
(400 x 370mm) x 2
Left Door (DF3506)
(516 x 396mm)
Right Divider (DF3505)
(522 x 378mm)
Left Divider (DF3504)
(522 x 378mm)
4
Right Door (DF3883)
(516 x 396mm)
Small Back (X548-293)
(548 x 293mm)
Large Back (X548-393)
(548 x 393mm) x 2
7
6
8
9 10
11
12

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Rule
Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A B
D E F
G H I
L
C
40mm Screw (F910) x 8
KJ
Large locking
nut (F900) x 8
Metal dowel (F901) x 8
Shelf stud (F110) x 16
19mm Screw (F461) x 2
38mm Screw (F81) x 10
Square
Bradawl
Spirit
level
13mm Screw (F63) x 8 Handle (F341) x 2
Foot
(F233) x 5
Hinge (F518) x 4
Hinge plate
(F523) x 4
Nail (F51) x 33
MStrap Screw Washer x 2
Overbalance protector kit (F269) x 1

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
Prepare the left end
Insert 2 large locking
nuts into the left end
. .
Fit 2 hinge plates onto
the left end , making
sure that the slot is
facing towards the front
edge.
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
J
B
1
1
J
Step 2
J
Prepare the right end
Insert 2 large locking
nuts into the right end
. .
Fit 2 hinge plates onto
the right end , making
sure that the slot is
facing towards the front
edge.
B
2
2
J
J
J
B
B
Finished
front edge
J
Finished
front edge
Step 3A
Prepare the top
Screw 8 metal dowels
into the top .
Note: Tighten the metal
dowels up fully against
the panels.
5
A
A
A
A
A
A
A
A
5
Finished
front edge
1
2
A
B
B
J

Finished
front edge
Finished
front edge
Polystyrene
block
Polystyrene
block
Finished
front edge
Assembly Instructions
5
Step 4
Step 5
Fit the sides to the top
Push the left side
and right side onto
the top .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left side and right
side .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Note: Place polystyrene
blocks from the
packaging underneath
the end panels to raise
the assembly. This will
make it easier when it
comes to fit the base.
2
5
1
B
B
1
2
Finished
front edge
B
B
Prepare the left
divider
Insert 2 large locking
nuts into the left
divider .
B
3
Step 6
Prepare the right
divider
Insert 2 large locking
nuts into the right
divider .
B
4
3
4
B
B
B
A
2
5
1

Polystyrene
block
Polystyrene
block
Assembly Instructions
6
Step 7
Left End (DF3502)
(522 x 378mm)
Fit the dividers
Push the left divider
and right divider onto
the top .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left divider and
right divider .
Note: Place polystyrene
blocks from the
packaging underneath
the divider panels to
raise the assembly. This
will make it easier when
it comes to fit the base.
4
5
3
B
3
4
4
3
5
Fit the base
Fit the base onto the
assembly using 8 screws
. .
7
E
E
E
E
E
E
E
E
E
7
Finished
front edge
Step 8

Assembly Instructions
7
Step 9
Step 10
Fit the feet
Fit the feet to the
base using screws .
L
7F
FF
L
FF
L
FF
L
FF
L
7
Fit the 2 large backs
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the 2 large
backs onto the unit.
Nail around the
outside edges of the 2
large backs .
Note: Make sure that
you have 6 nails left to fit
the small back in the
next step.
12
C
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
12
yy
yy
xx
b:
FF
L
C
xx
12
12

Fit the middle shelves
For each of the 2 middle
shelves , insert 4 shelf
studs at the required
height.
Lower the 2 middle
shelves down onto
the shelf studs .
Assembly Instructions
8
Step 11
Left End (DF3502)
(522 x 378mm)
Fit the small back
Place the small back
onto the unit.
Nail along the top and
bottom edge of the small
back .
Carefully stand the
unit up for the next
step.
These gaps are for
cable management
11
C
11
C
Warning: The
unit is heavy.
Lift with care.
11
Dx 4
Dx 4
Step 12
D
D
8
8
8
8Finished
front edge

Assembly Instructions
9
Step 13
Fit the end shelves
For each of the 2 end
shelves , insert 4 shelf
studs at the required
height.
Lower the end shelves
down onto the shelf
studs .
Dx 4
Dx 4
D
D
6
6
6
6
Step 14
90
K
Prepare the 2 doors
Push fit 2 hinges into
the left door and the
right door .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
H
K
9
10 K
H
H
K
H
H
K
H
H
K
H
H
9
10
Finished
front edge
Finished
front edge