Argos PENTON 490/9475 User manual

PENTON - Storage Coffee Table
490/9475
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
Important –Please read these instructions fully before starting assembly
Dimensions
Width - 90cm
Depth - 50cm
Height - 46cm
Issue 1 - 15/09/15

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

view from behind
view from behind
1Top panel (90 x 50cm)
2Front frame (88 x 44cm)
3Back panel (88 x 44cm)
4Side panel x 2 (44 x 46cm)
5Smaller drawer front x 3
(18.4 x 12.6cm)
6Larger drawer front x 2
(31 x 12.6cm)
7Drawer side x 10 (35.6 x 12.6cm)
8Smaller drawer back x 3
(16 x 12.6cm)
9Larger drawer back x 2
(28.6 x 12.6cm)
10 Side drawer runner x 4
(44 x 8cm)
11 Middle drawer runner x 3
(44 x 8cm)
12 Smaller drawer bottom x 3
(17.1 x 33.7cm)
13 Larger drawer bottom x 2
(29.7 x 33.7cm)
Components - Panels
Please check you have all the panels listed below
2

3
Components - Fittings
Please check you have all the fittings listed below
If you have damaged or missing components,
call the Customer Helpline: 03456 400 800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(small & medium)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
2m
A CB
Wooden dowel x 52 30mm Screw x 40 35mm Screw x 24
22mm Bolt x 10 Drawer
handle x 5
D E

Step 2
Step 1
Assembly Instructions
4
A
A
A
A
A
4
11
2x
4x 3x
Insert dowels into the
indicated parts.
A
Fixing side drawer
runners.
Fit side drawer runners
to the back panel
then fix using screws .
Attention:
Make sure the
holes in the middle of the
side drawer runners are
correctly positioned as
shown in the drawing
prior to fixing.
3
10 3
C
Attention! Attention!
10
10
10
10
10
C
C
C
C
C
10

Assembly Instructions
5
Step 4
Step 3
Fixing middle drawer
runners.
Fit middle drawer runners
to the back panel
then fix using screws .
11 3
4
4
Inserting side panels.
Insert side panels to
the back panel into
the grooves.
Attention!
Side panels must
be in the grooves and
aligned with the edges.
4
3
Attention!
4
3
11
11
3
3
C
11
CC
C
11

Assembly Instructions
6
Step 6
Step 5
Fixing front frame.
Place front frame
properly ensuring dowels
and side panels are
all fit into their holes at
the same time.
Attention!
Side panels must
be in the grooves and
aligned with the edges.
a: Fix drawer runners
and to the front frame
using screws .
4
2
C
10
10
2
4
Fixing top panel.
Two people are required
for an easier assembly.
Caution:
Carefully lay the
top panel on a soft and
clean surface to avoid
damaging the product.
Attach cabinet to the top
panel using screws .
1C
2
11
11
C
C
C
C
C
C
1
C
C
C
C
C
C

Assembly Instructions
7
Step 8
Step 7
a: Fix side drawer
runners to the side
panels using screws .
10
A
11
E
D
7
5B
8
B
a: b:
c: d:
B
B
7
5
7
8
12
B
B
E
D
b: Slide drawer bottom
into slots on drawer
sides and position drawer
back in place.
8
12
c: Holding the drawer
back , press the
drawer sides and fix them
using screws .
d: Using bolts attach
drawer handle to
drawer front.
Repeat step 8 for the
other smaller drawers.
Smaller drawer
assembly.
a: Attach drawer sides
to the drawer front
using screws .
3x
C
A
Only in the back of
the drawer runners.
a:
b:
10 11
10
10
11
10
C
C
A
A
A
A
b: Insert dowels only
into the back of the
drawer runners and
as shown.
Important:
After dowels
insertion, with
help, carefully stand the
product upright.
C
10

Step 9
9
Step 10
A
a: b:
c: d:
B
B
7
B
B
E
D
7
6
9
13
E
D
7
B
B
b: Slide drawer bottom
into slots on drawer
sides and position drawer
back in place.
c: Holding the drawer
back , press the
drawer sides and fix them
using screws .
d: Using bolts attach
drawer handle to
drawer front.
Repeat step 9 for the
other larger drawer.
Larger drawer
assembly.
a: Attach drawer sides
to the drawer front
using screws .
6
13
9
2x
Insert drawers into unit.
With the back of the
drawers past the front
frames, use a hammer to
tap dowels in flush to
drawer sides. This is a
safety catch to stop
drawer falling out.
Assembly is complete. A A
Assembly Instructions
14
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800